User's Manual
Table Of Contents
- Product Manual RFID Reader UF80
- 1 Identification
- 2 Declaration of Conformity
- 3 General Instructions
- 4 Safety Instructions
- 5 Product Specifications
- 6 Installation
- 7 Operation
- 7.1 Operating personnel
- 7.2 Communication protocol ASC-I1
- 7.2.1 Structure of the communication protocol
- 7.2.2 Package contents
- 7.2.3 Commands of protocol
- URY - Read data range (defined EPC code)
- M - Scan EPCs
- W - Write EPC code
- UWZ - Write data range of all EPC transponders (defined EPC code)
- ULZ - Locking all EPC transponders (defined EPC code)
- F - Query parameters
- P - Set parameter
- N - Reset
- O - Set output
- E - Error message
- H - Heartbeat
- V - Query software version
- K - Polling
- UFD - Query DHCP Enabled
- UPD - Set DHCP Enabled
- UFI - Query network settings
- UPI - Set network settings
- UFN - Query host name
- UPN - Set host name
- 7.2.4 Parameter
- Parameter 4 (0x04)
- Parameter 6 (0x06)
- Parameter 11 (0x0B)
- Parameter 12 (0x0C)
- Parameter 16 (0x10)
- Parameter 39 (0x27)
- Parameter 43 (0x2B)
- Parameter 47 (0x2F)
- Parameter 48 (0x30)
- Parameter 50 (0x32)
- Parameter 64 (0x40)
- Parameter 65 (0x41)
- Parameter 66 (0x42)
- Parameter 98 (0x62)
- Parameter 99 (0x63)
- Parameter 118 (0x76)
- Parameter 123 (0x7B)
- Parameter 158 (0x9E)
- Parameter 162 (0x02)
- Parameter 163 (0x00)
- Parameter 176 (0xB0)
- 7.3 Additional information
- 8 Service and Troubleshooting
- 9 Dismantling and Storage
- 10 Transport and Disposal
- 11 Accessories
- Index
Product Manual - RFID Reader UF80 67
Chapter 7
Operation
Parameter 64
(0x40)
Support configuration transponder
When the reader is started, a configuration transponder can be read and the
reader can then be configured correspondingly.
0x00 … Just like conventional transponders, configuration transponders are
displayed at the host during read operations and not analyzed when the
reader is started.
0x01 … The configuration transponder is filtered out during read operations and
not reported to the superordinate host. The configuration transponder
is not analyzed when the reader is started.
0x02 … The configuration transponder is not filtered out during read operations
and is reported to the superordinate host. The configuration
transponder is analyzed when the reader is started.
0x03 … The configuration transponder is filtered out during read operations and
not reported to the superordinate host. The configuration transponder
is analyzed when the reader is started.
Default: 0x00
Parameter 65
(0x41)
Result code start procedure (read only)
The parameter 0x41 can only be read out and provides information as to how the
start procedure went with regard to the configuration transponder.
0x00 … The start procedure of the reader has not been completed yet.
0x01 … The configuration transponder was not analyzed when the reader was
started
0x02 … No configuration transponder could be read.
0x03 … Several configuration transponders could be read.
0x04 … A data range of the configuration transponder could not be read.
0x05 … The configuration transponder could be read and the device settings
were up to date.
0x06 … The configuration transponder could be read and the device settings
were adapted.
0x07 … Due to invalid configuration data, the configuration transponder with the
up-to-date device setting was successfully written on.
0x08 … Due to invalid configuration data, it was attempted to adapt the
configuration transponder with the up-to-date device settings, which
failed.
Default: -