User's Manual
Table Of Contents
- Product Manual RFID Reader UF80
- 1 Identification
- 2 Declaration of Conformity
- 3 General Instructions
- 4 Safety Instructions
- 5 Product Specifications
- 6 Installation
- 7 Operation
- 7.1 Operating personnel
- 7.2 Communication protocol ASC-I1
- 7.2.1 Structure of the communication protocol
- 7.2.2 Package contents
- 7.2.3 Commands of protocol
- URY - Read data range (defined EPC code)
- M - Scan EPCs
- W - Write EPC code
- UWZ - Write data range of all EPC transponders (defined EPC code)
- ULZ - Locking all EPC transponders (defined EPC code)
- F - Query parameters
- P - Set parameter
- N - Reset
- O - Set output
- E - Error message
- H - Heartbeat
- V - Query software version
- K - Polling
- UFD - Query DHCP Enabled
- UPD - Set DHCP Enabled
- UFI - Query network settings
- UPI - Set network settings
- UFN - Query host name
- UPN - Set host name
- 7.2.4 Parameter
- Parameter 4 (0x04)
- Parameter 6 (0x06)
- Parameter 11 (0x0B)
- Parameter 12 (0x0C)
- Parameter 16 (0x10)
- Parameter 39 (0x27)
- Parameter 43 (0x2B)
- Parameter 47 (0x2F)
- Parameter 48 (0x30)
- Parameter 50 (0x32)
- Parameter 64 (0x40)
- Parameter 65 (0x41)
- Parameter 66 (0x42)
- Parameter 98 (0x62)
- Parameter 99 (0x63)
- Parameter 118 (0x76)
- Parameter 123 (0x7B)
- Parameter 158 (0x9E)
- Parameter 162 (0x02)
- Parameter 163 (0x00)
- Parameter 176 (0xB0)
- 7.3 Additional information
- 8 Service and Troubleshooting
- 9 Dismantling and Storage
- 10 Transport and Disposal
- 11 Accessories
- Index
Product Manual - RFID Reader UF80 76
Chapter 8
Service and Troubleshooting
Flashing pattern
parameter 0x41
0x01 … The configuration transponder was not analyzed when the reader
was started.
LED pattern: yellow LED flashes with 5 Hz
0x02 … No configuration transponder could be read.
LED pattern: red LED flashes with 1 Hz
0x03 … Several configuration transponders could be read.
LED pattern: red LED flashes with 1 Hz
0x04 … A data range of the configuration transponder could not be read.
LED pattern: red LED flashes with 1 Hz
0x05 … The configuration transponder could be read and the device settings
were up to date.
LED pattern: green LED flashes with 5 Hz
0x06 … The configuration transponder could be read and the device settings
were adapted.
LED pattern: green LED on permanently and yellow LED flashes with 1 Hz
0x07 … Due to invalid configuration data, the configuration transponder with the
up-to-date device setting was successfully written on.
LED pattern: green LED on permanently and yellow LED flashes with 5 Hz
0x08 … Due to invalid configuration data, it was attempted to
adapt the configuration transponder with the up-to-date device setting,
which failed.
LED pattern: red LED flashes with 5 Hz
At the present time, only the stationary configuration transponder V0 is
supported, which contains the following settings:
IP address, subnet address, gateway address, DHCP and buzzer volume
8.10 Software releases
ETSI
Release
date
Version Description
May 2011
UF80V1.0
First version
August 2011
UF80V1.1
Additional commands implemented
Support configuration transponder