INSTALLATION AND OPERATION INSTRUCTIONS FOR: SUPREMA RANGE STYLE WOOD BURNING COOKER Tested to EN12815 PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING, OPERATING OR SERVICING THIS APPLIANCE. Compliments for buying a Broseley Fires appliance.
INTRODUCTION Please read the following instructions carefully to get the best from your new purchase. The keys to safe, successful and efficient wood burning are good planning, correct installation and proper operation. Modern homes have better levels of insulation and are more energy efficient, with more effective and better seals on doors and windows.
INDEX 1. 1A. 2. 3. 4. 4A. 4B. 4C. 4D. 5.0 5A 6.0 6A 7.0 8.0 9.0 10.0 11.0 12.0 13.0 13A 13B 13C 13D 14.0 14A 14B TECHNICAL DATA HEATABLE AREA (VOLUME) KEY ENVIRONMENTAL CONSIDERATIONS TECHNICAL DESCRIPTION THE AIR CONTROLS THE PRIMARY AIR CONTROL (turning valve) SECONDARY AIR CONTROL (slider) FLUE DAMPER CONTROL BAR (pull push lever) OVER-FIRING WARNING FUEL ADVICE BURNING WOOD INITIAL BURNING & CURING OF THE STOVE.
1. TECHNICAL DATA PLEASE REFER TO ATTACHED TECHNICAL DRAWING FOR OTHER DIMENSIONS NOT LISTED HERE TOTAL POWER OUTPUT OUTPUT TO WATER OUTPUT TO AIR / THE ROOM WOOD CONSUMPTION / HR ( wood with MAX 20% humidity ) MINIMUM FLUE PIPE DIAMETER (adaptor for spigot reqd. 137mm to 150mm) BOILER CAPACITY OVEN SIZE W-D-H FIREBOX SIZE W-D-H FLUE DRAW (HOT) (Tested after one hour) MUST NOT EXCEED 25 PASCAL.
3. TECHNICAL DESCRIPTION These continuous fire cookers are suitable for cooking on the hob and in the oven. They will also heat living spaces or support a central heating system. They are ideal for holiday apartments and weekend houses or as a heating / cooking system during the whole year. The cooker is designed to burn wood as it’s primary fuel source. The cooker is made of galvanized metal sheet and enameled cast iron. Inside the fire chamber, there is a flat, cast iron grate.
4A THE PRIMARY AIR CONTROL (slider) The primary air control is found on the front left hand door, it is in the style of a slider. See fig 1. This will be used mainly when first lighting and establishing a new fire. This control allows combustion air to enter the appliance from below the grate. When the slider is moved to the left, it is letting less combustion air in. When slid to the right, the regulator is opening, letting more combustion air in.
5.0 FUEL ADVICE These appliances have been developed to burn wood. The results quoted in our literature are from test firings carried out using beech logs with a moisture content of less than 20%. 5A BURNING WOOD Hardwoods and Softwoods both have exactly the same calorific value pound for pound, however softwoods will burn nearly twice as fast as hardwoods meaning re-fuelling intervals will be shorter. Most firewood you purchase will be green and have a fair amount of water content.
7.0 OVEN OPERATION (only once fire is well established) Don’t pull out the damper control for the oven until the fire is established and creating a high heat output. • If you wish to use the oven, open the damper control by pulling the control rod. Once the fuel is burning intensely, the hot smoke can be sent round the oven to heat it.
.0 ASH REMOVAL • The removal of the ashes should be done when the appliance is cold. Ash must be removed periodically for the correct and efficient operation of your appliance. Don’t wait till the ash pan's completely full. The frequency of this ash removal will depend on the type of wood being burned as Softwoods and hardwoods create differing amounts of ash.
12.0 MAINTENANCE - CLEANING THE APPLIANCE Take great care choosing the products you use to clean your appliance. A major amount of cleaning can be carried out using hot soapy water and a soft cloth. Using the wrong products will cause damage to its surfaces. Never use bleach or chlorine based products, caustic cleaners, paint solvents, biological powders, coarse abrasives or salt.
13D GLASS CLEANING: There are various glass cleaners you can buy at stove shops that are specially designed to remove hydrocarbon (soot) and fly ash (mineral) deposits from the glass. Follow the manufacturer’s instructions. Typically, just spray a small amount of cleaner on the glass and use a paper towel or rag to wipe it clean. If you only burn logs in your appliance, then you can dip a damp cloth in the ash and use this to scrub the glass clean. 14.
INSTALLATION OF THE APPLIANCE 15.0 FLUE REQUIREMENTS The chimney is possibly the most important part to your installation; great care should be given to its design. An older chimney, in need of repair, is a fire hazard in any installation. The chimney must be thoroughly swept, checked for soundness and suitability, before any connection is made to the appliance. This must be carried out by a qualified person. This appliance must be installed into a ‘Class 1 Chimney’.
17.0 SITING THE APPLIANCE This appliance must not be fitted into a location where it will be impossible to service. The location must comply with the requirements laid down in the building regulations. 17A HEARTH REQUIREMENTS It is essential that the hearth / base on which the appliance will stand is strong enough to support the weight of the appliance and the chimney / flue. If not, independently support. It must be level and made of a suitably robust, non combustible material.
19.0 ASSEMBLING THE HANDRAILS There are three handrails, one for each side and one for the front. The handrails are bolted to the sides and the front of the appliance using the bolts provided.
ANNUAL SERVICE RECORD INSTALLATION DATE OF APPLIANCE: INSTALLATION ENGINEER: COMPANY NAME: COMPANY ADDRESS: CONTACT NUMBER . . . REG. No. POSTCODE: 1ST YEAR SERVICE completion date: SERVICE ENGINEER: COMPANY NAME: COMPANY ADDRESS: . . REG. No. . . POSTCODE: 2ND YEAR SERVICE completion date: SERVICE ENGINEER: COMPANY NAME: COMPANY ADDRESS: . . REG. No. . . POSTCODE: 3RD YEAR SERVICE completion date: SERVICE ENGINEER: COMPANY NAME: COMPANY ADDRESS: . . REG. No. . .
POSTCODE: LIMITED WARRANTY You, as the end user, have a contract by law with the supplier / dealer from whom you purchased the product. That dealer then has the same contract with the manufacturer or wholesaler and these have a contract with their suppliers. ALL CLAIMS MUST FOLLOW THIS PROCEDURE. Thank you for choosing a Product from Broseley Fires Ltd. This warranty gives you specific legal rights.
** End-user means the natural or legal person who owns the product and who has not acquired it with a view to reselling or installing it in the course of business © 2007-2008 Broseley Fires Ltd