ALEDIN 2 USER MANUAL BROTHER, BROTHER & SONS ApS user manual revision 1.
ALEDIN 2 USER MANUAL INTRO Brother, Brother & Sons ApS The information in this manual is subject to change without notice. Go to www.brothers-sons.dk for the latest version. Brother, Brother & Sons ApS assumes no responsibility for any errors or inaccuracies that may appear in this manual. All information and graphics are the property of Brother, Brother & Sons ApS. User Manual Version: December 2011 Customer and Warranty service: Contact your regional dealer.
ALEDIN 2 USER MANUAL CONTENTS Intro.......................................................................................................................... Index.......................................................................................................................... Safety Information...................................................................................................... Maintenance............................................................................................
ALEDIN 2 USER MANUAL SAFETY Safety Notice: It is important to read ALL safety information and instructions in this manual before installing and operating the product described. Safety symbol used in this manual: WARNING: Potential injury or damage to persons or product. WARNING: It is important to read ALL safety and installation instructions to avoid any damage to the product and potential injury to yourself and others. This product is for professional use only and has been designed for indoor use.
ALEDIN 2 USER MANUAL PRODUCT OVERVIEW LED (Peel protective sticker off before use) Lamp Adjustment PEEL OF BEFORE INSTALLATION Ground connector DMX OUT DMX IN POWER IN WWW.BROTHERS-SONS.DK user manual revision 1.
ALEDIN 2 USER MANUAL REBUILD CAUTION !! To avoid damage to equipment take electrostatic precautions when performing the retrofitting. Disconnect fixture from power and allow it to cool for 10 min. Retrofitting should only be performed by qualified personel. Tools needed to perform the retrofitting: Slotted srewdriver, recommended size 6,5 A pair of hands. Not too big or too small. Rebuild has only been tested with a left and a right hand, but in theory two left hands could do the job.
ALEDIN 2 USER MANUAL 1 1 Untighten quater turn screw (1) and open lid. 3 2 2 Disconnect ground wire (2) from lamp section. Unscrew srews (3) and remove lamp section. 3 5 PEEL OF BEFORE INSTALLATION PEEL OF BEFORE INSTALLATION 4 Attach ground wire (4) to the ALEDIN Remove protective plastic from LED (5) WWW.BROTHERS-SONS.DK user manual revision 1.
ALEDIN 2 USER MANUAL 4 Before mounting the aledin position the LED tower part farthest away from the quater turn. 5 6 Insert ALEDIN into the lamp housing and tighten screws (6) 6 7 Tighten quater turn screw (7) WWW.BROTHERS-SONS.DK user manual revision 1.
ALEDIN 2 USER MANUAL INSTALLATION Do not operate the product if the ambient temperature exceeds 40° C / 104°F Provide a minimum clearance of 0,1m (4 in.) around fans and air vents. This fixture must be connected to ground. This fixture is for indoor use only. Read the “Safety” and “Specifications” chapters first. Applying power: Never connect to dimmer power. Make sure the local power voltage is within the range specified. If so; connect a power cable and turn the power on.
ALEDIN 2 USER MANUAL AC Power This fixture must be connected to ground. Electrical: AC Power: 100 – 240 V nominal, 50/60 Hz Powersupply: Electronic switchmode Max power consumption: 200 w DMX Data link This product uses a 5-pin XLR for dmx input and output. Use shielded data cables. Do not overload the daisy chain. Up to a maximum of 32 devices can be used on a single dmx chain. DMX Channels: 1 at 8bit: Dimmer 3 at 8bit: Dimmer w. strobe 2 at 16bit: Dimmer 4 at 16bit: Dimmer w.
ALEDIN 2 USER MANUAL Software vers. 1_3_00 Linear curve on Indicator Response fast indicator Strobe on Indicator 8 bit Indicator 888888 MENU ENTER UP DOWN DMX present indicator Open menu / Go back Select / Confirm Scrolling UP / Increase value Scrolling DOWN / Decrease value DMX Channels Mode Channel Parameter Value Percent Function 8 Bit 1 Dimmer 0 - 255 0 - 100 Coarse dimming 8 Bit w.
ALEDIN 2 USER MANUAL Software vers.
ALEDIN 2 USER MANUAL Software vers. 1_3_00 SOFTWARE MENU ....continued Default values indicated by bold font Log Max Fan Fan RPS EEProm LED U PSU U LED int Log C° on time on LED Demo DMX HZ DMX CH DMX br LED EE Manual 0 Maximum fan speed logged. (in RPS) - READOUT ONLY Current fan speed (in RPS) - READOUT ONLY Developer info LED voltage in Volts - READOUT ONLY PSU voltage in Volts - READOUT ONLY for troubleshooting - READOUT ONLY Minimum and maximum logged temperature in °C UP and DOWN scrolls min.
ALEDIN 2 USER MANUAL SPECIFICATIONS Physical (Additional - when mounted): Depth: 0 mm / 0” Width: 0 mm / 0” Height: 97 mm / 3,82” Weight: 2,3 kg / 5 lbs Data: DMX Channels: 1 ch. at 8bit / 2 ch. if strobe channel is enabled 2 ch. at 16bit / 3 ch. if strobe channel is enabled Protocol: USITT DMX512-A Data In/Out: 5 pin locking XLR Electrical: Never connect to dimmer power Neutric PowerCon AC Power: 100 – 240 V, 50/60 Hz Powersupply: Electronic switchmode Max. power consumption: 200 W. Max Amp.: 0.
