Operation Manual Sewing Machine Product Code: 888-F50/F52/F60/F62/F70/F72 Be sure to read this document before using the machine. We recommend that you keep this document nearby for future reference.
INTRODUCTION INTRODUCTION Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT SAFETY INSTRUCTIONS”, and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference. IMPORTANT SAFETY INSTRUCTIONS Please read these safety instructions before attempting to use the machine.
IMPORTANT SAFETY INSTRUCTIONS 5 Always keep your work area clear: • Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot control free from the build up of lint, dust, and loose cloth. • Do not store objects on the foot controller. • Do not use extension cords. Plug the machine directly into the electrical outlet. • Never drop or insert foreign objects in any opening.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This machine is intended for household use. FOR USERS IN COUNTRIES EXCEPT EUROPEAN COUNTRIES This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
ABOUT THIS MANUAL ABOUT THIS MANUAL This manual was written for several machine models. The machine models are categorized according to their specifications and referred to as “Model” followed by a number. Refer to the Quick Reference Guide for the model of your machine. The screen displays may differ from the ones displayed on your machine. Refer to the Quick Reference Guide for details on accessories, settings screen and pre-programmed stitch patterns.
CONTENTS CONTENTS INTRODUCTION.................................................. i IMPORTANT SAFETY INSTRUCTIONS ................. i ABOUT THIS MANUAL ...................................... iv WHAT YOU CAN DO WITH THIS MACHINE .... iv B Basic operations Chapter 1 GETTING READY 2 Sewing with free motion mode ............................................. 44 Hands-free raising and lifting of the presser foot ................... 45 Stitch Setting Chart ............................................
CONTENTS D Decorative sewing Chapter 1 CHARACTER / DECORATIVE STITCHES 2 Sewing the Various Built-in Decorative Patterns .... 2 Selecting stitch patterns .......................................................... 2 Deleting a pattern................................................................... 3 Sewing attractive finishes ....................................................... 3 Basic sewing .......................................................................... 4 Combining patterns ............
Basic operations This section provides details on the initial setup procedures as well as descriptions of this machine’s more useful functions. Page number starts with “B” in this section. Chapter1 GETTING READY....................................................B-2 Chapter2 STARTING TO SEW ..............................................
Names of Machine Parts and Their Functions 1 Chapter GETTING READY Names of Machine Parts and Their Functions The names of the various parts of the machine and their functions are described below. Before using the machine, carefully read these descriptions to learn the names of the machine parts and their locations. Machine ■ Front view a C Thread cutter Pass the threads through the thread cutter to cut them. b c d D Needle threader lever e Use the needle threader lever to thread the needle.
Names of Machine Parts and Their Functions Needle and presser foot section Operation buttons b i c B d e f a g b 1 “Start/Stop” button c g f e 1 Needle bar thread guide d Pass the upper thread through the needle bar thread guide. 2 Needle plate The needle plate is marked with guides for sewing straight seams. 3 Needle plate cover Remove the needle plate cover to clean the bobbin case and race.
Names of Machine Parts and Their Functions Press to apply the selection or perform the operation. Operation panel and operation keys F Numeric keys Use these keys to quickly select one of the ten most often used stitches. When selecting other stitches, use these keys to type in the number of the desired stitch. G Back key b c a v Press this key to cancel the operation and return to the previous screen.
Names of Machine Parts and Their Functions Using the flat bed attachment Pull the top of the flat bed attachment to open the accessory compartments. B GETTING READY A presser foot accessory tray is stored in the accessory compartment of the flat bed attachment.
Names of Machine Parts and Their Functions Included accessories Included accessories may differ from the table below depending on your model. For more details on included accessories and their part codes of your machine, refer to the Quick Reference Guide. 1. 2. J 3. N 4. 5. I G 6. M R Zigzag foot “J” (on machine) Monogramming foot “N” Overcasting foot “G” Zipper foot “I” Blind stitch foot “R” Button fitting foot “M” 7. 8. 9. 10. 11. 12.
Names of Machine Parts and Their Functions Optional accessories The following are available as optional accessories to be purchased separately. Optional accessories differ depending on your model. For more optional accessories and their part codes, refer to the Quick Reference Guide. 1. 2. 4. 5. 6. Free motion echo quilting foot Free motion quilting foot “C” “E” Quilting foot Walking foot 1/4" quilting foot 1/4" quilting foot with guide 7. 9. 10. 11. 12. 8.
Names of Machine Parts and Their Functions Model 1 Page Automatic fabric sensor system (setting) 9 N/A N/A B-43 Fine adjustment horizontal (setting) 9 9 N/A D-10 Free motion foot height (setting) 9 N/A N/A B-44 Free motion mode (setting) 9 N/A Pivoting 9 N/A Presser foot height (setting) 9 N/A Presser foot lifter button 9 N/A Size selection (setting) Stitch name *1 Stitch number Basting stitch *1 9 9 9 9 Thread tension dial N/A Thread tension key 9 Step stitch patter
Turning the Machine On/Off Turning the Machine On/Off WARNING CAUTION • Use only the power cord included with this machine. • Do not use extension cords or multi-plug adapters with any other appliances plugged into them. Fire or electric shock may result. • Do not touch the plug with wet hands. Electric shock may result. • When unplugging the machine, always turn the main power to OFF first. Always grasp the plug to remove it from the electrical outlet.
Turning the Machine On/Off Turning on the machine Turning off the machine Make sure that the machine is turned off (the main ”), and then plug the power cord into the power supply jack on the right side of the machine. a power switch is set to “ Insert the plug of the power cord into a household b electrical outlet. When you are finished using the machine, turn it off. In addition, before transporting the machine to another location, be sure to turn it off.
LCD LCD Viewing the LCD When the power is turned on, the LCD comes on, and the following screen is displayed. The screen will vary slightly depending on your machine model. GETTING READY The screen is changed using the keys below the LCD. 4 3 2 1 5 6 7 8 No. Display 1 2 - 3 9 4 3 2 1 5 6 7 0 Item Name 8 9 Explanation Page Presser foot Shows presser foot to be used. B-31 Stitch preview Shows a preview of the selected stitch.
LCD Settings screen Press to change various sewing machine operations and sewing settings. Press to move to previous/next pages. * You can also move to next pages by pressing Press . to select the next/previous items. * Press (Downward arrow) to select the next item. * Press (Upward arrow) to select the previous item. Press to change the value of the selected item. Note • The parameters and number of pages in the settings screens differ depending on the model of your machine.
LCD 9 B E 0 C F A D G B H K I L J M N H I J K Specifies whether or not a beep is sounded with each operation. For details, refer to “Operation beep” in the “Appendix” section. Switches the needle area and work area lights to remain “ON” or “OFF”. Adjusts the brightness of the LCD. When set “ON”, reinforcement stitches are sewn at the beginning and/or end of sewing for a reinforcement stitch pattern, even when the reverse button is pressed.
LCD Adjust the input sensitivity by pressing the “-” or “+” b key. Choosing the display language • The lower the setting, the less sensitive the keys will be; the higher the setting, the more sensitive the keys will be. The default setting is “3”. a Press . b Select c Use the “-” or “+” key to choose the desired language. (Language) display.
Winding/Installing the Bobbin Winding/Installing the Bobbin Place the bobbin on the bobbin winder shaft so that the CAUTION Press down on the bobbin until it snaps into place. 1 2 1 Notch 2 Bobbin winder shaft spring Slide the bobbin winder in the direction of the arrow c until it snaps into place. * Actual size 1 This model 2 Other models 3 11.5 mm (approx. 7/16 inch) • The “Start/Stop” button lights up in orange. Remove the spool cap that is inserted onto the spool d pin.
Winding/Installing the Bobbin f Slide the spool cap onto the spool pin. Slide the spool cap as far as possible to the right, as shown, with the rounded side on the left. Memo • When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the spool. b c CAUTION • If the spool or the spool cap is not installed correctly, the thread may become tangled around the spool pin, causing the needle to break.
Winding/Installing the Bobbin While holding the thread near the spool with your right g hand, as shown, pull the thread with your left hand, While holding the thread with your left hand, wind the j thread that was pulled out clockwise around the and then pass the thread behind the thread guide cover and to the front. bobbin five or six times with your right hand. B 1 • Make sure that the thread between the spool and the bobbin is pulled tight.
Winding/Installing the Bobbin Press the “Start/Stop” button once to start winding the n bobbin. When the foot controller is plugged in, press down on the foot controller. Installing the bobbin Install the bobbin wound with thread. You can begin sewing immediately without pulling up the bobbin thread by simply inserting the bobbin in the bobbin case and guiding the thread through the slit in the needle plate cover.
Winding/Installing the Bobbin e Remove the bobbin cover. Hold the bobbin with your right hand with the thread f unwinding to the left, and hold the end of the thread with your left hand. Then, with your right hand, place the bobbin in the bobbin case. While lightly holding down the bobbin with your right h hand (1), guide the thread through the slit in the needle plate cover (2) and lightly pull it with your left hand (3). • The thread enters the tension spring of the bobbin case.
Winding/Installing the Bobbin j Reattach the bobbin cover. Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right side. 2 1 → The bobbin threading is finished. Next, thread the upper thread. Continue with the procedure in “Upper Threading” on page B-21. Memo • You can begin sewing without pulling up the bobbin thread.
Upper Threading Upper Threading CAUTION Turn on the machine. b Raise the presser foot lever to raise the presser foot. 1 1 Presser foot lever → The upper thread shutter opens so the machine can be threaded. • When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break. • Never use a thread weight of 20 or lower. • Use the needle and the thread in the correct combination.
Upper Threading e Place the spool of thread onto the spool pin. Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom. While using your right hand to lightly hold the thread i passed under the thread guide plate, pass the thread through the guides in the order shown below. CAUTION Note • If the presser foot has been lowered and the shutter is closed, the machine cannot be threaded.
Upper Threading l Slide the thread behind the needle bar thread guide. The thread can easily be slid behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand, as shown. Cut the thread with the cutter on the left side of the b machine. B 1 m 1 Needle bar thread guide Note Raise the presser foot lever.
Upper Threading Lower the needle threader lever on the left side of the d machine until it clicks, and then slowly return the lever to its original position. Threading the needle manually (without using the needle threader) When using specialty thread, such as transparent nylon thread, a wing needle or a twin needle which cannot be used with the needle threader, thread the needle as described below. a Thread the machine to the needle bar thread guide. b Lower the presser foot lever.
Upper Threading While lightly holding the upper thread with your left (Needle position button) twice to raise the needle. d hand, press Using the twin needle With the twin needle, you can sew two parallel lines of the same stitch with two different threads. Both upper threads should have the same thickness and quality. Be sure to use the twin needle, the horizontal spool pin and the appropriate spool cap.
Upper Threading Insert the horizontal spool pin onto the bobbin winder d shaft. Without passing the thread through the needle bar h thread guide, manually thread the right needle. Insert the horizontal spool pin so that it is perpendicular to the bobbin winder shaft. Insert the thread through the eye of the needle from the front. 1 • The needle threader cannot be used with the twin needle. If the needle threader is used with the twin needle, the machine may be damaged.
Upper Threading n Start sewing. • For details on starting to sew, refer to “STARTING TO SEW” on page B-33. → Two lines of stitching are sewn parallel to each other. B GETTING READY Note • When changing the sewing direction, press (Needle position button) to raise the needle from the fabric, and then raise the presser foot lever and turn the fabric. CAUTION • Do not try turning the fabric while the twin needle is down in the fabric, otherwise the needle may break or the machine may be damaged.
Replacing the Needle Replacing the Needle Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these precautions is extremely dangerous, for example, if the needle breaks and fragments are dispersed. Be sure to read and carefully follow the instructions below. CAUTION • Only use recommended home machine needles. Use of any other needle may bend the needle or damage the machine. • Never use bent needles.
Replacing the Needle d Checking the needle Sewing with a bent needle is extremely dangerous since the needle may break while the machine is being operated. Before using the needle, place the flat side of the needle on a flat surface and check that the distance between the needle and the flat surface is even. Press . • If is pressed while the presser foot is raised, an error message appears. Lower the presser foot. → The screen changes, and all keys and operation buttons are locked (except ).
Replacing the Needle While holding the needle with your left hand, use the g screwdriver to tighten the needle clamp screw. Turn the screw toward the back of the machine (counterclockwise). CAUTION • Be sure to insert the needle until it touches the needle stopper and securely tighten the needle clamp screw with the screwdriver, otherwise the needle may break or damage may result. h Press B-30 to unlock all keys and buttons.
Replacing the Presser Foot Replacing the Presser Foot Place a different presser foot below the holder so that CAUTION f the presser foot pin is aligned with the notch in the holder. • Use the presser foot appropriate for the type of stitch that you wish to sew, otherwise the needle may hit the presser foot, causing the needle to bend or break. • Only use presser feet designed specifically for this machine. Use of any other presser foot may result in injuries or damage to the machine.
Replacing the Presser Foot ■ Attaching the presser foot holder Note • When a stitch is selected, the icon for the presser foot that should be used appears in the screen. Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the machine, attach the correct presser foot, turn machine back on and then select the desired stitch again. a Raise the presser foot lever. Align the presser foot holder with the lower-left side of b the presser bar.
Sewing Chapter 2 STARTING TO SEW B Sewing STARTING TO SEW CAUTION • While the machine is in operation, pay special attention to the needle location. In addition, keep your hands away from all moving parts such as the needle and handwheel, otherwise injuries may occur. • Do not pull or push the fabric too hard while sewing, otherwise injuries may occur or the needle may break. • Never use bent needles. Bent needles can easily break, possibly resulting in injuries.
Sewing Character stitches There are five character stitch modes: Gothic font mode , Handwriting font mode , Cyrillic font mode , Outline font mode ■ When selecting from the preset utility stitches Since various stitches have been assigned to the numeric keys, these stitches can be selected simply by pressing the designated numeric key. and Japanese font mode . For details, refer to “Selecting stitch patterns” in the “Decorative sewing” section. Check that a screen.
Sewing f Sewing a stitch Turn the main power to ON and push a position button) to raise the needle. (Needle Lower the presser foot. You do not have to pull up the bobbin thread. Adjust the sewing speed with the sewing speed g controller. You can use this controller to adjust sewing speed during sewing. Select the desired stitch following the procedure b described in “Selecting a stitch pattern” above.
Sewing Insert the foot controller plug into its jack on the CAUTION b machine. • Do not press (Thread cutter button) after the threads have been cut. Doing so could tangle the thread or break the needle and damage the machine. 1 • Do not press (Thread cutter button) when there is no fabric set in the machine or during machine operation. The thread may tangle, possibly resulting in damage.
Sewing Sewing reinforcement stitches Reverse/reinforcement stitches are generally necessary at the beginning and end of sewing. You can use (Reverse stitch button) to sew reverse/reinforcement stitches (Refer to “Stitch Setting Chart” under the column for “Reverse/ Reinforcement stitching” on page B-46.).
Sewing Press (Reverse stitch button) or d stitch button). (Reinforcement Reverse stitch button 1 Reverse stitches (or reinforcement stitches) → The machine will sew reverse stitches (or reinforcement stitches) and stop. When the automatic reinforcement stitching function is not active while selecting character/ decorative stitches Machine starts sewing and then sews reinforcement stitches while holding the Reverse stitch button.
Setting the Stitch Setting the Stitch Note • Stitch settings return to their defaults if they are changed, when the machine is turned off or a different stitch is selected before the stitch setting is saved, refer to “Saving stitch settings” on page B-41. CAUTION • After adjusting the stitch width, slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break.
Setting the Stitch Setting the thread tension 5 You may need to change the thread tension, depending on the fabric and thread being used. 1 ■ Correct thread tension 2 The upper thread and the bobbin thread should cross near the center of the fabric. Only the upper thread should be visible from the right side of the fabric, and only the bobbin thread should be visible from the wrong side of the fabric.
Setting the Stitch Pushing the thread tension dial toward the right makes the thread tension tighter. If you wish to save specific settings for a stitch so that they can be used later, press after changing the settings to save the new settings with the selected stitch. This feature can be used only with utility stitches. To use a stitch length of 2.0 mm for the straight stitch a Select a straight stitch. b Set the stitch length to 2.0 mm.
Useful Functions Useful Functions Automatically cutting the thread Memo • Programmed thread-cutting will not be performed if the “Start/Stop” button is pressed while sewing. The machine can be set to automatically cut the threads at the end of the stitching. This is called “programmed threadcutting”. If programmed thread-cutting is set, automatic reverse/reinforcement stitching is also set. a Turn on the machine. b Select a stitch.
Useful Functions Select (Automatic fabric sensor system) in the a settings screen. Memo • Depending on the selected stitch, mirroring may not be possible; for example, buttonhole stitch. • When the machine is turned off, the mirroring setting is cancelled. Set the sensor system to “ON” by pressing the “-” or b “+” key. STARTING TO SEW Adjusting the presser foot pressure You can adjust the presser foot pressure (the amount of pressure applied to the fabric by the presser foot) on the settings screen.
Useful Functions Press the “Start/Stop” button to stop the machine at d the point where the sewing direction changes. Note • (Needle position) in the settings screen, must be set to the down position for the pivot function to be used. When (Needle position) is set in the raised position, cannot be used. The pivot function can only be used with stitches where presser foot J or N is indicated on the screen. If any other stitch is selected, available.
Useful Functions CAUTION B STARTING TO SEW • With free motion quilting, control the feeding speed of the fabric to match the sewing speed. If the fabric is moved faster than the sewing speed, the needle may break or other damage may result. ■ Adjusting free motion presser foot height Select a screen. b (Free motion foot height) in the settings Adjust the height that the quilting foot is raised above the fabric by pressing the “-” or “+” key.
Stitch Setting Chart Stitch Setting Chart Applications, stitch lengths and widths and whether the twin needle can be used are listed for utility stitches in the following table. This table applies to several models (Model 3, 2 and 1). Refer to the Quick Reference Guide for the model of your machine. *1 Patterns printed on the numeric keys on the machine can be selected directly. For details, refer to “Preset utility stitches” on page B-52.
Stitch Setting Chart Model 1 Stitch Model 3, 2 Stitch width Stitch length [mm (inch)] [mm (inch)] Stitch name Presser foot Applications Auto. Manual 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 1.0 (1/16) 0.2 - 5.0 (1/64 - 3/16) 3.5 (1/8) 2.5 - 5.0 (3/32 - 3/16) 5.0 (3/16) 2.5 - 5.0 (3/32 - 3/16) 2.0 (1/16) 0.4 - 5.0 (1/64 - 3/16) 2.5 (3/32) 0.4 - 5.0 (1/64 - 3/16) 5.0 (3/16) 3.5 - 5.
Stitch Setting Chart Model 1 Stitch Model 3, 2 Stitch width Stitch length [mm (inch)] [mm (inch)] Stitch name Presser foot Applications Auto. Manual Auto. Manual 0.0 (0) 0.0 - 7.0 (0 - 1/4) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 1.5 (1/16) 0.0 - 7.0 (0 - 1/4) 7.0 (1/4) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.4 - 5.0 (1/64 - 3/16) 1.4 (1/16) 0.0 - 5.0 (0 - 3/16) 1.8 (1/16) 0.4 - 5.0 (1/64 - 3/16) 1.6 (1/16) 0.4 - 5.0 (1/64 - 3/16) 2.0 (1/16) 0.4 - 5.0 (1/64 - 3/16) 2.0 (1/16) 0.4 - 5.0 (1/64 - 3/16) 2.5 (3/32) 0.
Stitch Setting Chart Model 1 Stitch Model 3, 2 Stitch width Stitch length [mm (inch)] [mm (inch)] Stitch name Presser foot Applications Auto. Manual 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 6.0 (15/64) 0.0 - 7.0 (0 - 1/4) 7.0 (1/4) 0.0 - 7.0 (0 - 1/4) 1.0 (1/16) 0.0 - 7.0 (0 - 1/4) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 6.0 (15/64) 0.0 - 7.0 (0 - 1/4) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 3.0 (1/8) 0.0 - 7.0 (0 - 1/4) 6.0 (15/64) 0.0 - 7.0 (0 - 1/4) 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 5.0 (3/16) 0.
Stitch Setting Chart Model 1 Stitch Model 3, 2 Stitch width Stitch length [mm (inch)] [mm (inch)] Stitch name Presser foot Applications Auto. Manual Auto. Manual 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 6.0 (15/64) 0.0 - 7.0 (0 - 1/4) 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 6.0 (15/64) 0.0 - 7.0 (0 - 1/4) 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 2.0 (1/16) 0.4 - 5.0 (1/64 - 3/16) 2.0 (1/16) 0.4 - 5.0 (1/64 - 3/16) 3.0 (1/8) 0.4 - 5.0 (1/64 - 3/16) 1.6 (1/16) 0.4 - 5.0 (1/64 - 3/16) 1.6 (1/16) 0.4 - 5.0 (1/64 - 3/16) 5.
Stitch Setting Chart Model 1 Stitch Model 3, 2 Stitch width Stitch length [mm (inch)] [mm (inch)] Stitch name Presser foot Applications Auto. Manual Auto.
Stitch Setting Chart ■ P reset utility stitches Stitch name Model 1 Preset utility stitches Model 3, 2 The most frequently used utility stitches have been assigned to the numeric keys. These stitches can be selected simply by pressing the designated key while in the preset utility stitch mode.
Sewing This section describes procedures for using the various utility stitches as well as other functions. It provides details on basic sewing in addition to the more expressive features of the machine, such as sewing tubular pieces and buttonholes. Page number starts with “S” in this section. Chapter1 SEWING ATTRACTIVE FINISHES......................... S-2 Chapter2 UTILITY STITCHES...................................................
Sewing Tips Chapter 1 SEWING ATTRACTIVE FINISHES Sewing Tips Trial sewing After you have set up the machine with the thread and needle appropriate for the type of fabric being sewn, the machine automatically sets the stitch length and width for the stitch that is selected. However, a trial piece of fabric should be sewn since, depending on the type of fabric and stitching being sewn, the desired results may not be achieved.
Sewing Tips Sewing an even seam allowance To sew an even seam, start sewing so that the seam allowance is to the right of the presser foot, and the edge of the fabric is aligned with either the right edge of the presser foot or a marking on the needle plate. ■ Aligning the fabric with the presser foot Sew while keeping the right edge of the presser foot a fixed distance from the edge of the fabric.
Sewing Various Fabrics Sewing Various Fabrics d Sewing thick fabrics Release the presser foot locking pin (black button). → The presser foot remains level, allowing the fabric to be fed. ■ If the fabric does not fit under the presser foot If the fabric does not fit easily under the presser foot, raise the presser foot lever even higher to bring the presser foot to its highest position. → After the seam is sewn, the presser foot will return to its original angle.
Sewing Various Fabrics Sewing stretch fabrics Sewing hook-and-loop fastener tape First, baste the pieces of fabric together, and then sew without stretching the fabric. CAUTION • Use only the adhesive-free hook-and-loop fastener tape which is designed for sewing. When the glue adheres to the needle or the bobbin hook race, it may cause malfunction. • If the hook-and-loop fastener tape is sewn with the thin needle (65/9-75/11), the needle may bend or break.
Basic Stitching Chapter 2 UTILITY STITCHES Basic Stitching Straight stitches are used for sewing plain seams. Presser foot Model 1 Stitch Model 3, 2 Stitch name Model 4 • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. Basic stitching a Baste or pin together the fabric pieces. b Attach zigzag foot “J”.
Basic Stitching ■ Changing the needle position The needle position used as the baseline is different for the straight stitch (left needle position) and the straight stitch (center needle position). 1 2 S 1 Straight stitch (left needle position) 2 Straight stitch (center needle position) UTILITY STITCHES When the stitch width of the straight stitch (left needle position) is set to its standard setting (0.
Blind Hem Stitching Blind Hem Stitching Secure the bottoms of skirts and pants with a blind hem. • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. Use a chalk to mark on the fabric about 5 mm (3/16 c inch) from the edge of the fabric, and then baste it.
Blind Hem Stitching Slide the item that you wish to sew onto the free arm, i make sure that the fabric feeds correctly, and then start sewing. ■ If the needle catches too much of the hem fold The needle is too far to the left. Decrease the stitch width so that the needle slightly catches the fold of the hem. Example: Thick fabric S 1 Free arm Position the fabric with the edge of the folded hem the presser foot lever.
Blind Hem Stitching Sew with the fold of the hem against the presser foot l guide. Press the “Start/Stop” button to stop sewing when you m are finished, and raise the presser foot and needle to remove the fabric by pulling it back. Note • Be sure to pull the fabric backward after finished sewing. If you pull the fabric toward side or forward, the presser foot may be damaged. n Remove the basting stitching and reverse the fabric.
Overcasting Stitches Overcasting Stitches Sew overcasting stitches along the edges of cut fabric to prevent them from fraying. Sew with the edge of the fabric against the presser foot d guide. Sewing overcasting stitches using overcasting foot “G” 1 S Presser foot Model 1 Model 3, 2 Stitch Stitch number Overcasting stitch 1-15 15* 13* 1-16 16 14 1-17 17 15 G 1 Needle drop point CAUTION • After the stitch width is adjusted, rotate the handwheel toward you (counterclockwise).
Overcasting Stitches Sewing overcasting stitches using zigzag foot “J” 1 Presser foot Stitch number 08* Zigzag stitch (Right) 1-11 11 10 2 steps elastic zigzag stitch 1-13 13 11 3 steps elastic zigzag stitch 1-14 14* 12* 1-18 18 16 Using the side cutter, seam allowances can be finished while the edge of the fabric is cut off. Five utility stitches can be used to sew overcasting stitches with the side cutter.
Overcasting Stitches a Remove the presser foot. f Hook the connecting fork of the side cutter onto the g at the beginning of the stitching. b needle clamp screw. Select a stitch. Make a cut of about 2 cm (3/4 inch) long in the fabric a 1 b Position the fabric in the side cutter. The cut in the fabric should be positioned over the guide plate of the side cutter.
Buttonhole Stitching/Button Sewing Buttonhole Stitching/Button Sewing Presser foot Model 1 Stitch Model 3, 2 Stitch name Model 4 • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. Buttonhole sewing The maximum buttonhole length is about 28 mm (1-1/8 inches) (diameter + thickness of the button). Buttonholes are sewn from the front of the presser foot to the back, as shown below.
Buttonhole Stitching/Button Sewing Use chalk to mark on the fabric the position and length a of the buttonhole. 2 d Select a stitch. Position the fabric with the front end of the buttonhole e mark aligned with the red marks on the sides of the buttonhole foot, and then lower the presser foot lever. 1 1 S A 1 Marks on fabric 2 Buttonhole sewing 2 buttonhole. Pass the upper thread down through the hole in the presser foot.
Buttonhole Stitching/Button Sewing Gently hold the end of the upper thread in your left g hand, and then start sewing. For keyhole buttonholes, use the eyelet punch to make a hole in the rounded end of the buttonhole, and then use the seam ripper to cut open the buttonhole. 1 → Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. h Press (Thread cutter button) once. Raise the presser foot, and then remove the fabric.
Buttonhole Stitching/Button Sewing Hook the gimp thread onto the part of buttonhole foot a “A” shown in the illustration. Raise the presser foot lever, and then slide the feed dog b position switch, located at the rear of the machine on the base, to the machine). b (to the left as seen from the rear of S a It fits into the grooves, and then loosely tie it. c Attach buttonhole foot “A”. d Select stitch c Attach button fitting foot “M”. d Select stitch .
Buttonhole Stitching/Button Sewing Turn the handwheel toward you (counterclockwise) to g check that the needle correctly goes into the two holes of the button. If it seems as if the needle will hit the button, remeasure the distance between the holes in the button. Adjust the stitch width to the distance between the buttonholes. ■ Attaching a shank to a button To sew the button with a shank, attach the button with space between it and the fabric, and then wind the thread by hand.
Zipper Insertion Zipper Insertion Model 1 Presser foot Stitch 03* J Model 3, 2 Stitch name Model 4 • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. Press open the seam allowance from the wrong side of d the fabric.
Zipper Insertion h Select stitch . Inserting a side zipper CAUTION Stitching is visible on only one piece of fabric. Use this type of zipper application for side openings and back openings. • When using zipper foot “I”, be sure to select the straight stitch (center needle position), and slowly turn the handwheel toward you (counterclockwise) to check that the needle does not touch the presser foot. If a different stitch is selected or the needle hits the presser foot, the needle may bend or break.
Zipper Insertion Press the seam allowance so that the right side (the side e that will not be stitched) has an extra 3 mm (1/8 inch). Sew the zipper to the piece of fabric with the extra 3 i mm (1/8 inch), starting from the base of the zipper. 1 S 2 1 Wrong side of fabric 2 3 mm (1/8 inch) CAUTION or pin the zipper in place. • When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break.
Zipper Insertion n Topstitch around the zipper. Sew reverse stitches at the end of the zipper opening and align the zipper teeth with the side of the presser foot. 3 2 1 1 2 3 4 5 4 5 Right side of fabric End of zipper opening Reverse stitches Beginning of stitching Basting stitching CAUTION • When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break.
Zipper/piping Insertion Zipper/piping Insertion A zipper and piping can be sewn in place. Slide the presser foot over either the left or right feed Presser foot 01* ** S Stitch number Straight stitch (Left) 1-01 01* Left sewing position * Stitch patterns can be selected directly by pressing the numeric keys on the machine during preset utility stitch mode. Refer to “Basic operations” section.
Zipper/piping Insertion h Topstitch around the zipper. 1 d 3 2 4 1 2 3 4 Stitching Right side of fabric Basting stitching End of zipper opening CAUTION • When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break. i Remove the basting stitching. Inserting a piping Place the piping between two fabrics inside out, as a shown below.
Sewing Stretch Fabrics and Elastic Tape Sewing Stretch Fabrics and Elastic Tape a Pin the elastic tape to the wrong side of the fabric. Pin the elastic tape to the fabric at a few points to make sure that the tape is uniformly positioned on the fabric. Presser foot Model 1 Stitch Model 3, 2 Stitch name Model 4 • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section.
Appliqué, Patchwork and Quilt Stitching Appliqué, Patchwork and Quilt Stitching • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. Appliqué stitching Presser foot Model 1 Stitch Model 3, 2 Stitch name Model 4 Cut out the appliqué, leaving a seam allowance of a between 3 and 5 mm (1/8 and 3/16 inch).
Appliqué, Patchwork and Quilt Stitching Turn the handwheel toward you (counterclockwise), f and then begin sewing around the edge of the appliqué, making sure that the needle drops just outside of the appliqué. Piecing Sewing together two pieces of fabric is called “piecing”. The fabric pieces should be cut with a 6.5 mm (1/4 inch) seam allowance. Sew a piecing straight stitch 6.5 mm (1/4 inch) from either the right side or the left side of the presser foot.
Appliqué, Patchwork and Quilt Stitching ■ Piecing using the 1/4" quilting foot with guide (sold separately with some models) This quilting foot can sew an accurate 1/4 inch or 1/8 inch seam allowance. It can be used for piecing together a quilt or for topstitching. a Press Topstitching quilting, 1/8 inch Sew with the edge of the fabric aligned with the left side of the presser foot end. a , and then attach the 1/4” quilting foot with guide.
Appliqué, Patchwork and Quilt Stitching e Start sewing. a Baste the fabric to be quilted. When the end of the stitching is reached, stop the b Remove the presser foot and the presser foot holder. f machine. Sew until the mark at the lower edge of the 1/4" quilting foot aligns with the lower edge of the fabric. • For details, refer to “Removing and attaching the presser foot holder” in the “Basic operations” section. Hook the connecting fork of the walking foot onto the c needle clamp screw.
Appliqué, Patchwork and Quilt Stitching ■ Using the quilting guide (sold separately with some models) Use the quilting guide to sew parallel stitches that are equally spaced. Insert the stem of the quilting guide into the hole at the a rear of the walking foot or presser foot holder. ■ Using free motion open toe quilting foot “O”* or quilting foot* * Sold separately with some models.
Appliqué, Patchwork and Quilt Stitching Hold the quilting foot in place with your right hand, e and tighten the presser foot holder screw using the CAUTION screwdriver with your left hand. 1 Presser foot holder screw • When using free motion quilting foot “C”, be sure to use the straight stitch needle plate and sew with the needle in middle (center) needle position. If the needle is moved to any position other than the middle (center) needle position, the needle may break, which may result in injuries.
Appliqué, Patchwork and Quilt Stitching Attach free motion quilting foot “C” at the front with e the presser foot holder screw aligned with the notch in the quilting foot. After sewing is finished, slide the feed dog position (to the right as seen from the rear of the machine) and turn the handwheel to raise the feed dogs. h switch lever to Note a b 1 Presser foot holder screw 2 Notch • Free motion open toe quilting foot “O” can also be used with the straight stitch needle plate.
Appliqué, Patchwork and Quilt Stitching CAUTION e Tighten the screw with the included screwdriver. • With free motion quilting, control the feeding speed of the fabric to match the sewing speed. If the fabric is moved faster than the sewing speed, the needle may break or other damage may result. S Memo Slide the feed dog position switch, located at the rear (to the left as seen from the rear of the machine).
Appliqué, Patchwork and Quilt Stitching Finished project e Select stitch . While sewing, slide the sewing speed controller to f adjust the stitch width. Slide the controller to the left to make the width narrower. Slide the controller to the right to make the width wider. Narrower Wider After sewing is finished, slide the feed dog position g switch lever to (to the right as seen from the rear of the machine) and turn the handwheel to raise the feed dogs.
Reinforcement Stitching Reinforcement Stitching Reinforce points that will be subject to strain, such as sleeve holes, inseams and pocket corners. a • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. Determine the desired length of the bar tack. Set the button guide plate on buttonhole foot “A” to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).
Reinforcement Stitching e Pull down the buttonhole lever as far as possible. Darning a 1 Buttonhole lever The buttonhole lever is positioned behind the bracket on the buttonhole foot. 1 2 1 Buttonhole lever 2 Bracket Gently hold the end of the upper thread in your left f hand, and then start sewing. 1 Reinforcement stitching a Determine the desired length of the darning. Set the button guide plate on buttonhole foot “A” to the desired length.
Reinforcement Stitching Position the fabric so that the needle is 2 mm (1/16 d inch) in front of the area to be darned. Raise the presser foot lever, remove the fabric, and g then cut the threads. h 1 Raise the buttonhole lever to its original position. Memo • If the fabric does not feed, for example, because it is too thick, increase the stitch length. For details, refer to “Setting the stitch length” in the “Basic operations” section.
Eyelet Stitching Eyelet Stitching Eyelets, such as those on belts, can be sewn. Use the eyelet punch to cut a hole in the center of the Model 1 Presser foot Stitch Model 3, 2 Stitch name Model 4 • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. 71 N f eyelet. Stitch number Eyelet stitch a 4-15 91 Attach monogramming foot “N”.
Attaching Patches or Emblems to Shirt Sleeves Attaching Patches or Emblems to Shirt Sleeves Use these stitch patterns to attach patches or emblems to pant legs, shirt sleeves, etc. Lower the needle into the fabric at the beginning of the d stitching, and then start sewing. Lower the needle at the upper-right corner. Presser foot S → The fabric is fed toward the back of the machine, as usual.
Attaching Patches or Emblems to Shirt Sleeves k After you have sewn to the corner, stop the machine, and then select stitch again. After sewing 3 to 5 stitches at the beginning of the l stitching, stop the machine. Memo • The feeding direction of the fabric differs depending on the stitch that is selected. Be sure to guide the fabric while machine is sewing.
Decorative Stitching Decorative Stitching The utility stitches contain the following decorative stitches. Fagoting Presser foot Stitching across an open seam is called “fagoting”. It is used on blouses and children's clothing. This stitch is more decorative when thicker thread is used. Use an iron to fold the two pieces of fabric along their a seams. Baste the two pieces of fabric, separated by about 4 b mm (3/16 inch), onto thin paper or a sheet of water- soluble stabilizer.
Decorative Stitching c Scallop stitching Sew parallel stitching at intervals of 1 cm (3/8 inch). The wave-shaped repeated pattern that looks like shells is called “scalloping”. It is used on the collars of blouses and to decorate the edges of projects. a 1 Attach monogramming foot “N”. 1 1 cm (3/8 inch) b Select stitch . • Do not use reverse/reinforcement stitching or thread cutting.
Decorative Stitching Shell tuck stitching Joining The gathers that look like shells are called “shell tucks”. They are used to decorate trims, the front of blouses or cuffs made of thin fabrics. a Fold the fabric along the bias. Decorative bridging stitches can be sewn over the seam allowance of joined fabrics. This is used when making a crazy quilt. a Attach zigzag foot “J”. J S b 2 Attach zigzag foot “J”.
Decorative Stitching Partially removing threads is called “drawnwork”. This gives beautiful results with fabrics that have a loose weave. Heirloom stitching When sewing with the wing needle, the needle holes are enlarged, creating a lace-like decorative stitch. This is used to decorate hems and tablecloths on thin or mediumweight fabrics in addition to plain weave fabrics. a Two ways to create drawnwork are described below. ■ Drawnwork (Example 1) Install the wing needle.
Decorative Stitching ■ Drawnwork (Example 2) S Pull out several threads from two sections of the fabric, a separated by an unfrayed section of about 4 mm (3/16 inch). UTILITY STITCHES 1 1 4 mm (3/16 inch) b Attach monogramming foot “N”. c Select stitch d Sew along the center of the unfrayed section. .
Decorative Stitching S-46
Decorative sewing This section provides instructions on sewing character stitches and decorative stitches as well as on adjusting and editing them. In addition, it describes how to use MY CUSTOM STITCH, which allows you to create original stitch patterns. Page number starts with “D” in this section. The screen display and machine illustration may vary slightly, depending on the machine model. Chapter1 CHARACTER / DECORATIVE STITCHES................ D-2 Chapter2 MY CUSTOM STITCH.............................
Sewing the Various Built-in Decorative Patterns 1 Chapter CHARACTER / DECORATIVE STITCHES Sewing the Various Built-in Decorative Patterns Cross stitch stitches Selecting stitch patterns This machine is equipped with the following decorative stitches and character stitches. Character stitch patterns Operation key Font Icon Gothic Handwriting Outline Cyrillic Japanese Note • The stitch numbers vary depending on your sewing machine model. Refer to the Quick Reference Guide.
Sewing the Various Built-in Decorative Patterns ■ Character stitch patterns Each press of Æ Æ changes the font in the following order. Memo Æ • If a new pattern is selected without deleting the previously selected one, the first and second patterns are combined. (Refer to “Combining patterns” on page D-5.) • If two patterns or more have been already selected, the pattern that was selected last is removed. Æ Æ ... Select the desired font, and then specify the numbers of the desired characters.
Sewing the Various Built-in Decorative Patterns Basic sewing a Select a decorative/character stitch pattern. b Attach monogramming foot “N”. c Place the fabric under the presser foot, pull the upper thread out to the side, press (Needle position button) to lower needle into fabric and then lower the presser foot. Memo • When sewing character stitches, the machine automatically sews reinforcement stitches at the beginning and end of each character.
Sewing the Various Built-in Decorative Patterns Combining patterns a Select the first category and pattern. → The selected pattern appears on the screen. Repeating combined patterns When multiple stitches are combined, the sewing machine stops when the pattern displayed on the screen has been completed. Use the following operations to sew a combined pattern repeatedly. a After the patterns have been combined, press .
Sewing the Various Built-in Decorative Patterns Checking the selected pattern c Repeat steps a and b. When the specified pattern is not displayed on the screen, check the pattern using the following steps. a Select (Check) in the settings screen. Changing the stitch density b c Press the “-” or “+” key, and confirm the pattern. Press . If a satin stitch has been selected, the stitch density can be changed. a Select a satin stitch pattern.
Sewing the Various Built-in Decorative Patterns b Select (Elongation) in the settings screen, and select the desired length from among “1” to “5”. Creating step stitch patterns (For models equipped with step stitch patterns) Decorative stitches can be shifted to the left or right by half the width of the pattern, allowing you to create a step-shaped pattern. (Equipped on some models. Refer to page B-8.) This is called a “step stitch pattern”.
Sewing the Various Built-in Decorative Patterns d Press . Mirroring a pattern image a After a single pattern has been selected, press mirror the pattern image horizontally. to → The next pattern selected is moved half a width to the left. e Press to specify that the patterns will be sewn repeatedly. → • For details, refer to “Repeating combined patterns” on page D-5. ■ Examples of step stitch patterns D-8 appears on the screen and the selected stitch is mirrored.
Sewing the Various Built-in Decorative Patterns Returning to the beginning of the pattern You can return to the beginning of the pattern after trial sewing or when the stitching is sewn incorrectly. a Press the “Start/Stop” button to stop the machine, and then press . Saving a pattern Combined patterns can be stored for later use. Since stored patterns are not lost after the sewing machine is turned off, they can be recalled at any time. Up to 15 patterns can be stored.
Sewing the Various Built-in Decorative Patterns Retrieving a pattern a b a Attach monogramming foot “N”. b Select c Start sewing. Press once or twice until a list of saved patterns like the one shown below is displayed. Select the desired saved pattern using or or . → The sewing machine stops after it has finished sewing the pattern. . d Check the sewn pattern. If the part of the pattern indicated in the illustration is sewn uniformly, the pattern is correctly aligned.
Sewing the Various Built-in Decorative Patterns f Press the “-” or “+” key to adjust the vertical position. i Press j Select . or once again, start the sewing machine and check the stitching. Continue adjusting the pattern until it is sewn correctly. → Make the necessary adjustments according to how the pattern is sewn. D CHARACTER / DECORATIVE STITCHES Press “+” to increase the vertical space in the design. Press “-” to decrease the vertical space in the design.
Designing a Stitch Chapter 2 MY CUSTOM STITCH Designing a Stitch With the MY CUSTOM STITCH function, you can sew stitch patterns that you design yourself Drawing a sketch of the pattern c Mark the points in the pattern that are positioned at intersections in the grid, and then link those points with a continuous straight line. d Determine the sewing order. Prepare a grid sheet set. a Draw a sketch of the pattern on the grid sheet set.
Designing a Stitch b Press f on the operation panel as many times as necessary until is displayed, and press . Select whether to finish editing the pattern and return to the sewing screen or to continue editing. Select either of them using the “-” or “+” key, and then press . 1 2 1 Continue editing 2 Finish editing → The MY CUSTOM STITCH screen is displayed. c Check the grid sheet set, and specify the coordinates of the first point. Specify the coordinates using the “-” .
Designing a Stitch Examples of designs Enter each of the points indicated in the table to sew the sample stitch.
Appendix This section provides important information for operating this machine. Please read this section to find troubleshooting tips and pointers as well as how to keep your machine in the best working order. Page number starts with “A” in this section. Chapter1 MAINTENANCE AND TROUBLESHOOTING ........
Care and Maintenance Chapter 1 MAINTENANCE AND TROUBLESHOOTING Care and Maintenance Restrictions on oiling In order to prevent damaging this machine, it must not be oiled by the user. This machine was manufactured with the necessary amount of oil applied to ensure correct operation, making periodic oiling unnecessary.
Care and Maintenance ■ If there is a screw in the needle plate cover 1 Use the L-shaped (or disc-shaped) screwdriver to remove the screw in the needle plate cover. Insert the bobbin case so that the S mark on the z mark on the machine. i bobbin case aligns with the a b a b 2 Grasp both sides of the needle plate cover, and then slide it toward you. A • Align the S and z marks. a ■ If there is no screw in the needle plate cover a 1 Needle plate cover g Remove the bobbin case.
Troubleshooting Troubleshooting If the machine stops operating correctly, check the following possible problems before requesting service. You can solve most problems by yourself. If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at “ http://support.brother.com/ ”. If the problem persists, contact your authorized Brother dealer or the nearest Brother authorized service center.
Troubleshooting Pull the thread to pass it through the slit in the needle plate cover, then cut it with the cutter. ■ Remedy/check details Remove the tangled thread, and then correct the upper threading. Remove the tangled thread. If it cannot be removed, a cut the thread with scissors. • For details, refer to “Cleaning the race” on page A-2. b Remove the upper thread from the machine.
Troubleshooting Pass the thread under the thread guide plate, and then f pull it up. Incorrect thread tension ■ Symptoms • Symptom 1: The bobbin thread is visible from the right side of the fabric. (Refer to illustration below) • Symptom 2: The upper thread appears as a straight line on the right side of the fabric. • Symptom 3: The upper thread is visible from the wrong side of the fabric.
Troubleshooting Cause 2 A needle and thread appropriate for the fabric are not being used. The machine needle that should be used depends on the type of fabric sewn and the thread thickness. If a needle and thread appropriate for the fabric are not being used, the thread tension will not be adjusted correctly, causing wrinkles in the fabric or skipped stitches. • If the upper thread is visible from the wrong side of the fabric Using thread tension key (For models equipped with thread tension key.
Troubleshooting Fabric is caught in the machine and cannot be removed h Remove the bobbin case. If threads remain in the bobbin case, remove them. If the fabric is caught in the machine and cannot be removed, the thread may have become tangled under the needle plate. Follow the procedure described below to remove the fabric from the machine.
Troubleshooting Remove any threads in the race and around the feed l dogs. m Turn the handwheel to raise the feed dogs. Align the two screw holes in the needle plate with the n two holes at the needle plate mounting base, and then fit the needle plate onto the machine. Lightly finger-tighten the screw on the right side of the o needle plate. Then, use the L-shaped (or disc-shaped) 1 S mark 2 z mark 3 Bobbin case screwdriver to firmly tighten the screw on the left side.
Troubleshooting ■ Checking machine operations If the needle plate has been removed, check machine operations to confirm that installation has been completed correctly. a Turn on the machine. b Select stitch . Note • Do not yet install the presser foot and thread. Slowly turn the handwheel toward you c (counterclockwise), and look from all sides to check that the needle falls at the center of the opening in the needle plate.
Troubleshooting If the thread become tangled under the bobbin winder a seat, press the “Start/Stop” button once to stop the bobbin winding. When the foot controller is plugged in, remove your foot from the foot controller. Cut the thread with scissors beside the bobbin-winding b thread guide.
Troubleshooting List of symptoms ■ Getting ready Symptom Cannot thread the needle. Cannot lower the presser foot with the presser foot lever. (For models equipped with the presser foot lifter button) Bobbin thread does not wind neatly on the bobbin. While winding the bobbin, the bobbin thread was wound below the bobbin winder seat. The bobbin thread cannot be pulled up. Nothing appears in the LCD. The LCD screen is fogged up. The sewing light does not come on.
Troubleshooting ■ While sewing Symptom Machine does not operate. Probable Cause Reference “Start/Stop” button was not pressed. Press the “Start/Stop” button. B-35 The bobbin winder shaft is pushed to the right. Move the bobbin winder shaft to the left. B-15 There is no pattern selected. Select a pattern. B-34 Presser foot is not lowered. Lower the presser foot. B-35 “Start/Stop” button was pushed with the foot controller attached.
Troubleshooting Symptom Upper thread breaks. The thread is tangled on the wrong side of the fabric. The upper thread is too tight. Bobbin thread breaks. A-14 Probable Cause Remedy Reference Machine is not threaded correctly (used the wrong spool cap, spool cap is loose, the thread did not catch the needle bar threader, etc.) Rethread the machine correctly. B-21 Knotted or tangled thread is being used. Remove any knots or tangles.
Troubleshooting Symptom Fabric puckers. Skipped stitches High-pitched sound while sewing Fabric does not feed through the machine. Remedy Reference There is a mistake in the upper or bobbin threading. Check the steps for threading the machine and rethread it correctly. B-21 Spool cap is set incorrectly. Check the method for attaching the spool cap, then reattach the spool cap. B-21 Using improper needle or thread for the selected fabric. Check the “Fabric/Thread/Needle Combination” chart.
Troubleshooting Symptom The fabric feeds in the opposite direction. Probable Cause Remedy Reference The feed mechanism is damaged. Contact your authorized Brother dealer or the nearest Brother authorized service center. – The needle clamp screw is loose. Firmly tighten the needle clamp screw. If the needle is bent or blunt, replace it with a new one. B-29 Needle is turned, bent or the point is dull. Replace the needle. B-29 Thread is tangled below the needle plate.
Troubleshooting ■ After sewing Symptom Probable Cause Thread tension is incorrect. Pattern does not turn out. Reference Upper threading is incorrect. Check the steps for threading the machine and rethread the machine. B-21 Bobbin is set incorrectly. Reset the bobbin. (If needle plate was removed, reinstall needle plate and tighten screws prior to installing bobbin case. Check to make sure needle enter through the center of needle plate opening.
Troubleshooting Error Messages Cause/Solution 3 This message is displayed when the “Start/Stop” button was pressed while the foot controller was connected. 4 This message is displayed when the buttonhole lever is down, a stitch other than a buttonhole is selected, and a button, such as the “Start/Stop” button, is pressed. 5 This message is displayed when the buttonhole lever is up, a buttonhole stitch is selected, and a button, such as the “Start/Stop” button, is pressed.
Troubleshooting Error Messages Cause/Solution 12 This message is displayed when the motor locks due to tangled thread or for other reasons related to thread delivery. 13 This message is displayed when you try to sew with a stitch other than a middle needle position stitch while the straight stitch needle plate is installed. This message is displayed when the needle plate is removed with the machine on.
Specifications Operation beep Nothing appears in the LCD Each time a key is pressed you will hear one beep. If an incorrect operation is performed you will hear two or four beeps. If nothing appears in the LCD when the machine is turned on, the brightness of the LCD is either too light or too dark. If this is the case, perform the following operation. ■ If a key is pressed (correct operation) a One beep sounds. ■ If an incorrect operation is performed Two or four beeps sound.
Index Index Numerics D 1/4" quilting foot ....................................................................... S-28 1/4" quilting foot with guide ..................................................... S-28 7 mm satin stitches .................................................................... D-2 Darning .................................................................................... S-36 Darning stitch ...........................................................................
Index Manual needle threading ......................................................... B-24 Mirroring ........................................................................ B-42, D-8 Mirroring stitches ..................................................................... B-42 MY CUSTOM STITCH ............................................................. D-12 N Needle condition ............................................................................. B-29 position ....................................
Index Utility stitches ................................................................ B-34, B-46 W Winding bobbin ....................................................................... B-15 Wing needle ............................................................................. S-44 Z Zigzag stitches ............................................................... S-12, Zigzag width adjustment .......................................................... Zipper insertion centered .........................
Please visit us at http://support.brother.com/ where you can get product support and answers to frequently asked questions (FAQs).
