GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Operation Manual Computerized Sewing Machine Product Code: 888-V11
IMPORTANT SAFETY INSTRUCTIONS Please read these safety instructions before attempting to use the machine. DANGER - To reduce the risk of electric shock: 1 Always unplug the machine from the electrical outlet immediately after using, when cleaning, when making any user servicing adjustments mentioned in this manual, or if you are leaving the machine unattended. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons.
Always keep your work area clear: • Never operate the machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot control free from the build up of lint, dust, and loose cloth. • Do not store objects on the foot controller. • Do not use extension cords. Plug the machine directly into the electrical outlet. • Never drop or insert any object into any opening. • Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8 For repair or adjustment: • If the Light unit (light-emitting diode) is damaged, it must be replaced by authorized dealer. • In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. Use this machine only for its intended use as described in this manual.
FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY IMPORTANT • In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug. • Always replace the fuse cover. Never use plugs with the fuse cover omitted. • If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead.
5
—————————————————————————————————————————————————————————— Contents IMPORTANT SAFETY INSTRUCTIONS ............................................................................... 1 Introduction ........................................................................................................................ 8 Names of Machine Parts and Their Functions ..................................................................... 8 Machine ........................................................................
Changing the sewing direction ....................................................................................................................... 48 Sewing curves ................................................................................................................................................ 48 Sewing thick fabrics ....................................................................................................................................... 48 Sewing thin fabrics .................
Introduction Thank you for choosing this product. Before using this sewing machine, carefully read “Important Safety Instructions”, and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference. Names of Machine Parts and Their Functions Machine a Bobbin winder (page 15) Use the bobbin winder when winding the bobbin.
Needle and presser foot section a Needle threader lever Use the needle threader to thread the needle. b Buttonhole lever Lower the buttonhole lever when sewing buttonholes and bar tacks. c Presser foot holder The presser foot is attached to the presser foot holder. d Presser foot holder screw Use the presser foot holder screw to hold the presser foot holder in place. e Presser foot The presser foot applies pressure to the fabric during sewing. Attach the appropriate presser foot for the selected stitch.
Operation panel The operation panel, located on the front of the sewing machine, allows you to select a stitch and specify how the stitch will be sewn. a LCD (liquid crystal display) Error messages (1), the stitch length (mm) (2), and the stitch width (mm) (3) are displayed here. b Stitch length key (page 40) Use to adjust the length of the stitch. (Press the “–” side for a shorter stitch length, or press the “+” side for a longer stitch length.
Accessories After opening the box, check that the following accessories are included. If any item is missing or damaged, contact your dealer. Included accessories The following items should also be included in the box. Note ● The screw for the presser foot holder is available through your authorized dealer. (Part code: XA4813-051) 1. 10. 2. 11. 18. 3. 4. 5. 6. 7. 8. 12. 13. 14. 15. 16. 17. 19. 20. 21. 22. 23. 9.* * 75/11 1 needle 90/14 1 needle 100/16 1 needle No.
Optional accessories The following are available as optional accessories to be purchased separately. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. No. 1 2 3 4 5 6 Part Code Americas Others F054 Side cutter SA177 (XC3879-152) Quilting guide SA132 F016N (XC2215-052) Wide table SA552 WT8 (XE2472-001) F033N Walking foot SA140 (XC2214-052) F005N Quilting foot SA129 (XC1948-052) F036N Adjustable zipper/piping foot SA161 (XC1970-052) Part Name No.
1 GETTING READY 1 Turning the Machine On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure to observe the following precautions concerning the power supply. WARNING ● Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine. ● Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power supply jack on the machine.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Turning on the machine Prepare the included power cord. Make sure that the sewing machine is turned ”), and then plug the power cord into the power supply jack on the right side of the machine. a off (the main power switch is set to “ Insert the plug of the power cord into a b household electrical outlet.
Preparing for Upper and Lower Threading Winding the bobbin 1 Wind the thread onto the bobbin. a b c d a Hook of the bobbin-winding thread guide b Pretention disk c Bobbin winder shaft d Bobbin CAUTION ● Only use the bobbin (part code: SA156, SFB(XA5539-151)) designed specifically for this sewing machine. Use of any other bobbin may result in injuries or damage to the machine. ● The included bobbin was designed specifically for this sewing machine.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Slide the spool cap onto the spool pin. f With the slightly rounded side of the spool cap positioned toward the left, slide the spool cap onto the spool pin as far as possible to the right so that the spool is moved to the right end of the spool pin.
While using your left hand to hold the thread j that was passed through the bobbin-winding thread guide, use your right hand to wind the end of the thread clockwise around the bobbin five or six times. m Press (start/stop button) once. When the foot controller is plugged in, press down on the foot controller. X The bobbin starts spinning and the thread is wound around the bobbin.
GETTING READY——————— — — —— — —— — —— — — —— — —— — —— — — —— — —— — —— ————————————————————————————————————————————————————————————————— — b Installing the bobbin Turn off the sewing machine (set it to “ ”). Install the bobbin wound with thread. CAUTION ● Use a bobbin that has been correctly wound, otherwise the needle may break or the thread tension will be incorrect. Slide the latch on the right side of the bobbin c cover to the right, and then remove the bobbin cover.
While lightly holding down bobbin with your e right hand as shown, guide the thread through the slit a and b). • At this time, check that the bobbin easily rotates counterclockwise. Reattach the bobbin cover. f Insert the tab in the lower-left corner of the bobbin cover (A), and then press down on the right side (B). 1 B Then, pull the thread toward you to cut it with the cutter (c). A Memo ● You can begin sewing without pulling up the bobbin thread.
GETTING READY——————— — — —— — —— — —— — — —— — —— — —— — — —— — —— — —— ————————————————————————————————————————————————————————————————— — Threading the upper thread In this section, the procedures for installing the spool for the upper thread and threading the needle are described. b a a Spool pin b Mark on handwheel CAUTION ● When threading the machine, carefully follow the instructions.
Press (needle position button) once or c twice to raise the needle. Fully insert the spool for the upper thread e onto the spool pin Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom. a Needle position button • If the needle is not correctly raised, the sewing machine cannot be threaded. Check that the mark on the handwheel points up as shown in the illustration below.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — f Slide the spool cap onto the spool pin. While holding the spool with your right hand, g pull the thread with your left hand, and then pass the thread under the thread guide. Memo ● When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the spool.
Slide the thread into the thread take-up lever j from the right to the left. While lowering the needle threader lever, m hook the thread onto the guide. a 1 a Thread take-up lever Memo ● If the needle is not raised, the thread takeup lever cannot be threaded. Be sure to press the needle position button to raise the needle before threading the thread take-up lever. a Needle threader b Thread c Guide k guide.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Raise the presser foot lever, pass the end of p the thread through the presser foot, and then d Raise the presser foot lever. pull out about 5 cm (2 inches) of thread toward the rear of the machine.
Manually thread the left needle with the c upper thread. Using the twin needle With the twin needle, you can sew two parallel lines of the same stitch with two different threads. Both upper threads should have the same thickness and quality. Be sure to use the twin needle and the extra spool pin. For details on the stitches that can be sewn with the twin needle, refer to “Stitch Settings” (page 79). Pass the thread through the eye of the needle from the front to the back.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Without passing the thread through the g needle bar thread guide, manually thread the right needle. Pass the thread through the eye of the needle from the front to the back. Start sewing. k • For details on starting to sew, refer to “Starting to sew” (page 42). X Two lines of stitching are sewn parallel to each other.
Replacing the Needle This section provides information on sewing machine needles. 1 Needle precautions Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these precautions is extremely dangerous, for example, if the needle breaks and fragments are dispersed. Be sure to read and carefully follow the instructions below. CAUTION ● Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Needle types and their uses The sewing machine needle that should be used depends on the fabric and thread thickness. Refer to the following table when choosing the thread and needle appropriate for the fabric that you wish to sew.
Checking the needle Sewing with a bent needle is extremely dangerous since the needle may break while the machine is being operated. Before using the needle, place the flat side of the needle on a flat surface and check that the distance between the needle and the flat surface is even. Replacing the needle Replace the needle as described below. Use the screwdriver and a correct needle, as described in “Checking the needle”. 1 a twice to raise the needle.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Loosen the needle clamp screw and remove d the needle. Hold the needle with your left hand, and then turn the screwdriver counterclockwise with your right hand. a While holding the needle with your left hand, f tighten the needle clamp screw. Turn the screwdriver clockwise. b Install the twin needle in the same way.
Replacing the Presser Foot Presser foot precautions 1 Be sure to observe the following precautions concerning the presser feet. CAUTION ● Use the presser foot appropriate for the type of stitch that you wish to sew, otherwise the needle may hit the presser foot, causing the needle to bend or break. ● Only use presser feet designed specifically for this sewing machine. Use of any other presser foot may result in injuries or damage to the machine.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Place the presser foot to be installed below the e holder so that the presser foot pin is aligned Raise the presser foot lever to check that the g presser foot is securely attached. with the notch in the holder. Position the presser foot so the letter indicating the presser foot type (J, A, etc.) is positioned to be read.
■ Attaching the presser foot holder Align the presser foot holder with the presser a bar. a Using the optional walking foot With the optional walking foot, both pieces of fabric are fed evenly by the feed dogs and the teeth on the presser foot. This is useful when sewing fabrics that are hard to feed such as vinyl and leather and when sewing fabrics that easily slip such as velvets or when quilting. Use the screwdriver to attach the walking foot.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Lower the presser foot lever, insert the presser c foot holder screw, and then tighten the screw c Raise the presser foot lever. with the screwdriver. a a a Presser foot lever a Presser foot holder screw X The presser foot is raised.
Useful Functions Functions useful in improving sewing efficiency are described below. ■ When the needle stops in the raised position The needle stops in the raised position when sewing ends. Changing the needle stop position Normally, the sewing machine is set to leave the needle in the fabric when sewing is stopped. Instead, the machine can be set to leave the needle raised when sewing is stopped. a Turn off the sewing machine. Memo ● After sewing is finished, the fabric can be pulled out.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Sewing Cylindrical or Large Pieces When sewing cylindrical or large pieces of fabric, remove the flat bed attachment. Stitching cylindrical pieces Removing the flat bed attachment makes it easier to sew cylindrical pieces such as cuffs and pant legs. a Sewing large pieces of fabric The optional wide table makes sewing large pieces of fabric easier.
Install the wide table. c Keeping the wide table level, fully slide it into Install the flat bed attachment back in its f original position. place. The lower right corner section of the wide table extends over the front section of the sewing machine bed. 1 2 1 a Lower right corner b Sewing machine bed Note ● The optional wide table is available through your Brother dealer. Turn the screw at the bottom of each leg to d adjust their height so the wide table will be level with the sewing machine bed.
GETTING READY————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — 38
2 SEWING BASICS Starting to Sew Basic sewing operations are described below. Before operating the sewing machine, read the following precautions. 2 CAUTION ● While the machine is in operation, pay special attention to the needle. In addition, keep your hands away from all moving parts such as the needle, handwheel, and thread take-up lever, otherwise injuries may occur. ● Do not pull or push the fabric too hard while sewing, otherwise injuries may occur or the needle may break. ● Never use bent needles.
SEWING BASICS ————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Selecting a stitch Select each stitch by using the pattern selection dial. a Turn on the sewing machine. Adjusting the stitch length and width ■ Example: To select stitch Turn the pattern selection dial until “4” a appears in the pattern display window. Press “+” or “–” side of (stitch length b key) to adjust the stitch length.
Press “+” or “–” side of (stitch width c key) to adjust the stitch width. b a b c d a Positioning the fabric – + c d Stitch width key Stitch width Narrow Wide Be sure that the fabric pieces are sewn in the correct order and that the right and wrong sides of the fabric are aligned correctly. a Turn on the sewing machine. The straight stitch (left needle position) is automatically selected.
SEWING BASICS ————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — While holding the end of the thread and the d fabric with your left hand, turn the handwheel toward you (counterclockwise) with your right hand to lower the needle to the starting point of the stitching. Starting to sew Once you are ready to start sewing, you can start the sewing machine.
b Press (start/stop button) once. Insert the foot controller plug into its jack on b the side of the sewing machine. a Start/stop button The machine starts sewing. 2 a Foot controller jack c Turn on the sewing machine. • If you continue pressing the (start/stop button) immediately after the sewing starts, the machine will sew at a slow speed. When the end of the stitching is reached, (start/stop button) once. c press X The machine stops sewing with the needle down (in the fabric).
SEWING BASICS ————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Once you are ready to start sewing, slowly e press down on the foot controller. Pressing down on the foot controller increases the sewing speed; releasing the pressure on the foot controller decreases the sewing speed.
After sewing 3 to 5 stitches, press c (reverse/reinforcement stitch button). Keep (reverse/reinforcement stitch button) held down until you reach the beginning of the stitching. After 3 to 5 reverse stitches have been sewn, (reverse/reinforcement stitch button). g release X The machine stops sewing. Press (start/stop button), or press down on h the foot controller. At this time, if (start/stop button) is held down, the machine sews at a slow speed.
SEWING BASICS ————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Cutting the thread a sewing machine is stopped, press When you wish to finish the stitching and the (needle position button) once to raise the needle. Automatically sewing reverse/ reinforcement stitches The sewing machine can be set to automatically sew reverse or reinforcement stitches at the beginning and end of the stitching.
After reaching the end of the stitching, press e the reverse/reinforcement stitch button once. ■ Correct thread tension The upper thread and the bobbin thread should cross near the center of the fabric. Only the upper thread should be visible from the right side of the fabric, and only the bobbin thread should be visible from the wrong side of the fabric.
SEWING BASICS ————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Useful Sewing Tips Various ways to achieve better sewing results are described below. Refer to these tips when sewing. Trial sewing After a stitch is selected, the machine automatically sets the stitch width and length for the stitch that was selected.
■ If thick seams are being sewn and the fabric does not feed at the beginning of stitching The fabric may not feed when thick seams are being sewn and the presser foot is not level, as shown below. In this case, use the presser foot locking pin (black button on the left side of zigzag foot “J”) so that the presser foot remains level while sewing, allowing the fabric to be fed smoothly. • After the seam is sewn, the presser foot will return to its normal operation.
SEWING BASICS ————— ——— ——— ——— ——— ———— ———— ——— ———— ——— —— —— —— ——— ——— —— —— — —— — ——— ———— ——— — —— — —— — ——— — —— ———— ——— ——— ——— ——— —— —— ———— — Sewing hook-and-loop fastener b Lightly hold the end of the upper thread. a CAUTION ● Use only the ungummed hook-and-loop fastener which is for sewing. If the glue is attached to the needle or the bobbin hook race, it may cause malfunction. ● If the hook-and-loop fastener is sewn with the thin needle (65/9-75/11), the needle may bend or break.
3 UTILITY STITCHES Overcasting Zigzag stitch 3-point zigzag stitch Overcasting stitch Application J Overcasting and attaching appliqués Stitch Length [mm (inch)] Twin Needle Stitch Width [mm (inch)] Presser Foot Stitch Name Pattern Sew overcasting along the edges of cut fabric to prevent them from fraying. Four stitches are available for overcasting. Walking Foot Reverse/ Reinforcement Stitching Auto Manual Auto Manual 3.5 (1/8) 0.0–7.0 (0–1/4) 1.4 (1/16) 0.0–4.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Sewing overcasting stitches using zigzag foot “J” Sewing overcasting stitches using overcasting foot “G” a Turn on the machine. a Turn on the machine. b With the pattern selection dial, b With the pattern selection dial, select or . select Attach zigzag foot “J”. or . Attach overcasting foot “G”.
Basic Stitching Straight stitch Stitch Width [mm (inch)] Application Basic stitching, J sewing gathers or pintucks, etc. Left Attaching zippers, basic stitching, and J sewing gathers or pintucks, etc. Attaching sleeves, sewing inseams, J sewing stretch fabrics and decorative stitching Center Triple stretch stitch Stitch Length [mm (inch)] Auto Manual Twin Needle Presser Foot Stitch Name Pattern Straight stitches are used for sewing plain seams. Three stitches are available for basic stitching.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Blind Hem Stitching Stitch Width [mm (inch)] Twin Needle Stitch Name Presser Foot Pattern The bottoms of skirts and pants are hemmed. Two stitches are available for blind hem stitching. Stitch Length [mm (inch)] Application Manual Walking Foot Reverse/ Reinforcement Stitching Auto Manual Auto Blind hem stitching R on medium weight fabrics 0 (0) –3 – 3 2.0 (1/16) 1.0–3.
Position the fabric with the edge of the folded e hem against the guide of the presser foot, and Memo then lower the presser foot lever. If the needle is incorrectly positioned, the stitching results will be as shown below. Correct each result as described below. 4 a b ● If the needle catches too much of the hem fold The needle is positioned too far to the left. Press the “+” side of the stitch width key to adjust the needle position so that the needle slightly catches the fold of the hem.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Buttonhole Stitching Buttonhole stitch Stitch Width [mm (inch)] Stitch Length [mm (inch)] Application Auto Manual Twin Needle Presser Foot Stitch Name Pattern Buttonholes can be sewn. Three stitches are available for sewing buttonholes. Walking Foot Reverse/ Reinforcement Stitching Auto Manual Secured buttonA holes for fabrics that have backings 5.0 (3/16) 3.0–5.0 (1/8-3/16) 0.5 0.2–1.
Use chalk to mark on the fabric the position a and length of the buttonhole. 2 c Turn on the machine. d With the pattern selection dial, select 1 , or . Attach buttonhole foot “A”. e • For details, refer to “Replacing the presser foot” (page 31). Pass the upper thread down through the hole f in the presser foot, and then pull it under the a Marks on fabric b Button hole sewing presser foot, as shown.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Pull down the buttonhole lever as far as h possible. Use the enclosed seam ripper to cut towards m the pin and open the buttonhole. a a a Buttonhole lever The buttonhole lever should be positioned behind the metal bracket on the buttonhole foot.
■ Changing the stitch width Press the “+” or “–” side of the stitch width key to adjust the stitch width. – + Button sewing Buttons can be sewn on with the sewing machine. Buttons with 2 or with 4 holes can be attached. Measure the distance between the holes in the a button to be attached.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— g Place the button into button fitting foot “M”. Start sewing. i Set the sewing speed controller to the left (so that the speed will be slow). a a Button X The button is held in place. • When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the button so that the needle goes into the two holes toward the rear of the sewing machine, and then sew them in the same way.
■ Attaching a shank to a button To sew the button with a shank, attach the button with space between it and the fabric, and then wind the thread by hand. This attaches the button securely. Place the button into button-sewing foot “M”, a and then pull the shank lever toward you. 1 3 a Shank lever After sewing is finished, cut the upper thread b with plenty of excess, wind it around the thread between the button and the fabric, and then tie it to the upper thread at the beginning of the stitching.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Zipper Insertion Stitch Width [mm (inch)] Application Attaching zippers, basic stitching, and J sewing gathers or pintucks, etc. Straight Center stitch Stitch Length [mm (inch)] Auto Manual – – Auto Manual Twin Needle Presser Foot Stitch Name Pattern A zipper can be sewn in place. Walking Foot 2.5 0.2–5.
Align the seam with the center of the zipper, e and then baste the zipper in place. h Topstitch around the zipper. a b c b a d c a Wrong side of fabric b Basting stitching c Zipper f With the pattern selection dial, select stitch 3 a b c d . Attach the presser foot holder to the right side g of the pin of zipper foot “I”.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— a Turn on the machine. Align the zipper teeth with the pressed edge of f the fabric having the extra 3 mm (1/8 inch), b stitches up to the zipper opening. Attach zigzag foot “J” and sew straight and then baste or pin the zipper in place. • With the right sides of the fabric facing each other, sew reverse stitches after reaching the zipper opening.
Sew the zipper to the piece of fabric with the i extra 3 mm (1/8 inch), starting from the base of the zipper. Attach the presser foot holder to the other side l of the pin of zipper foot “I”. If the presser foot holder was attached to the right side of the pin in step h, change it to the left side of the pin. a I b CAUTION ● When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Sewing Stretch Fabrics and Elastic Tape Stitch Width [mm (inch)] Stitch Length [mm (inch)] Application Auto Manual Auto Manual Twin Needle Presser Foot Stitch Name Pattern Stretch fabrics can be sewn and elastic tape can be attached. Walking Foot Reverse/ Reinforcement Stitching Stretch stitch Sewing stretch fab1.0 J rics and decorative (1/16) stitching 1.0–3.0 (1/16–1/8) 2.5 1.0–4.
c With the pattern selection dial, select stitch . Attach zigzag foot “J”. d • For details, refer to “Replacing the presser foot” (page 31). Sew the elastic tape to the fabric while e stretching the tape so that it is the same length as the fabric. While pulling the fabric behind the presser foot with your left hand, pull the fabric at the pin nearest the front of the presser foot with your right hand.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Appliqué, Patchwork and Quilt Stitching Zigzag stitch Application J Overcasting and attaching appliqués Stitch Length [mm (inch)] Auto Manual Auto Manual 3.5 (1/8) 0.0–7.0 (0–1/4) 1.4 (1/16) 0.0–4.0 (0–3/16) Appliqué stitch J Appliqué stitching 3.5 (1/8) Fagoting stitch Fagoting, smockJ ing and decorative stitching 5.
d Turn on the machine. e With the pattern selection dial, select stitch or . f • For details, refer to “Replacing the presser Attach zigzag foot “J”. foot” (page 31). Patchwork (crazy quilt) stitching Fold the edge of the top piece of fabric and a place it over the lower piece. b pattern spans over both pieces.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Sew with the center of the presser foot g aligned along the center of the two pieces of fabric. Attach the quilting foot to the presser foot c holder screw. The pin on the quilting foot should be positioned over the needle clamp screw.
f Turn on the machine. g With the pattern selection dial, select stitch or . h then move the fabric to follow the pattern. Use both hands to stretch the fabric taut, and Reinforcement stitches are sewn at the beginning and end of stitching. a 3 a Pattern • Reverse stitches cannot be sewn when the feed dogs are lowered. After sewing is finished, slide the feed dog i position switch to its original position and turn the handwheel to raise the feed dogs. • The feed dogs are normally left raised.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Reinforcement Stitching Triple stretch stitch Bar tack stitch Stitch Width [mm (inch)] Stitch Length [mm (inch)] Application Attaching sleeves, sewing inseams, J sewing stretch fabrics and decorative stitching Reinforce openings and areas A where the seam easily comes loose Auto Manual Twin Needle Presser Foot Stitch Name Pattern Reinforce points that will be subject to strain, such as sleeve holes, inseams a
c Bar tack stitching With the pattern selection dial, select stitch Bar tacks are one type of reinforcement stitching used to strengthen points subject to strain, such as pocket corners and openings. As an example, the procedure for sewing bar tacks at pocket corners is described below. . Attach buttonhole foot “A”. d • For details, refer to “Replacing the presser foot” (page 31). Pass the upper thread down through the hole e in the presser foot, and then pull it under the presser foot, as shown.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Pull down the buttonhole lever as far as g possible. a a Buttonhole lever The buttonhole lever should be positioned behind the metal bracket on the buttonhole foot. a b a Buttonhole lever b Bracket Gently hold the end of the upper thread in h your left hand, and then start sewing. X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops.
Using the side cutter (optional) Overcasting stitch Presser Foot Stitch Name Pattern By using the optional side cutter, overcasting stitching can be sewn while the edge of the fabric is cut off. Stitch Width [mm (inch)] Stitch Length [mm (inch)] Reverse/ Reinforcement Stitching Application Auto Manual Auto Manual Basic stitching, S sewing gathers or pintucks, etc. 0.0 (0) 0.0–2.5 (0–3/32) 2.5 (3/32) 0.2–5.0 (1/64–3/16) Reverse Overcasting on S thin or medium weight fabrics 3.5 (1/8) 2.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— Position the side cutter so that the side cutter f pin is aligned with the notch in the presser foot holder, and then slowly lower the presser foot lever. Position the fabric. j Position the fabric so that the right side of the cut is on top of the guide plate and the left side of the cut is underneath the presser foot. b a a a Notch in presser foot holder b Pin a Guide plate X The side cutter is attached.
Lower the presser foot lever, and then start k sewing. X A seam allowance is cut while the stitching is sewn. If stitch is sewn, the seam allowance will be 3 about 5 mm (3/16 inch). a a 5 mm (3/16 inch) Note ● The side cutter can cut as much as one layer of 13-oz. denim. ● After using the side cutter, clean it by removing any lint or dust. ● If the side cutter can no longer cut fabric, use a rag to apply a small amount of oil to the cutting edge of the cutter.
UTILITY STITCHES ———————————————————————————————————————————————————————————————————— 78
4 APPENDIX Stitch Settings Applications, stitch lengths and widths and whether the twin needle can be used are listed for utility stitches in the following table. CAUTION ● When using the twin needle, be sure to attach zigzag foot “J”, otherwise the needle may break or the machine may be damaged. Straight stitch Left Center Stitch Width [mm (inch)] Application Basic stitching, J sewing gathers or pintucks, etc. Attaching zippers, basic stitching, and J sewing gathers or pintucks, etc. 0.0 (0) 0.0–7.
Stitch Width [mm (inch)] Stitch Length [mm (inch)] Application Manual Twin Needle Presser Foot Stitch Name Pattern APPENDIX —— — ——— — —— ———— ——— ——— ————— ——— ——————— ———————— ————— ——— ——— — ——— ——— — —— — —— ——— —— ——— ——— —— —— —— — —— ——— —— —— — —— — —— — — —— — ——— — Walking Foot Reverse/ Reinforcement Stitching Auto Manual Auto Blind hem stitching R on medium weight fabrics 0 (0) –3 – 3 2.0 (1/16) 1.0–3.
Maintenance Simple sewing machine maintenance operations are described below. Restrictions on oiling In order to prevent damaging this machine, it must not be oiled by the user. This machine was manufactured with the necessary amount of oil applied to ensure correct operation, making periodic oiling unnecessary. b Raise the needle and presser foot lever. c Pull the flat bed attachment off to the left.
APPENDIX ———————————— — — —— — —— — —— — — —— — —— — —— — — —— — —— — —— —————————————————————————————————————————————————————————— ——————— — Use the enclosed cleaning brush or a vacuum g cleaner to remove any lint and dust from the Insert the tabs on the needle plate cover into i the needle plate, and then slide the cover back race and its surrounding area. into position. a b a Cleaning brush b Race • Do not apply oil to the race or bobbin case.
Troubleshooting If the machine stops operating correctly, check the following possible problems before requesting service. You can solve most problems by yourself. If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at “ http://solutions.brother.com ” . If the problem persists, contact your dealer or the nearest authorized service center.
APPENDIX ———————————— — — —— — —— — —— — — —— — —— — —— — — —— — —— — —— —————————————————————————————————————————————————————————— ——————— — While holding the bobbin in place with your d finger, pass the thread through the slit in the needle plate. • Hold down the bobbin with your right hand, and then pull the end of the thread around the tab with your left hand. Tangled thread on wrong side of fabric ■ Symptom • The thread becomes tangled on the lower side of the fabric.
Raise the presser foot using the presser foot d lever. Pass the thread under the thread guide cover g from the back to the front. Hold the thread with your right hand so that there is no slack in the thread that is pulled out, and then pass the thread under the thread guide cover with your left hand. a Presser foot lever • If the presser foot is not raised, the sewing machine cannot be threaded correctly. a Press (needle position button) once or e twice to raise the needle.
APPENDIX —— — ——— — —— ———— ——— ——— ————— ——— ——————— ———————— ————— ——— ——— — ——— ——— — —— — —— ——— —— ——— ——— —— —— —— — —— ——— —— —— — —— — —— — — —— — ——— — Incorrect thread tension ■ Symptoms • Symptom 1: The lower thread is visible from the upper side of the fabric. • Symptom 2: The upper thread appears as a straight line on the upper side of the fabric. • Symptom 3: The upper thread is visible from the lower side of the fabric.
Cut out the tangled threads, and then remove g the bobbin. Fabric is caught in the machine and cannot be removed If the fabric is caught in the sewing machine and cannot be removed, the thread may have become tangled under the needle plate. Follow the procedure described below to remove the fabric from the machine. If the operation could not be completed according to the procedure, instead of attempting to complete it forcefully, contact your nearest authorized service center.
APPENDIX ———————————— — — —— — —— — —— — — —— — —— — —— — — —— — —— — —— —————————————————————————————————————————————————————————— ——————— — Use the enclosed disc-shaped screwdriver to j loosen the two screws on the needle plate. Note ● Be careful not to drop the removed screws in the machine. Turn the handwheel to check that the feed dogs move smoothly and do not contact the edges of the slots in the needle plate.
CAUTION ● Never use a bobbin case that is scratched, otherwise the upper thread may become tangled, the needle may break or sewing performance may suffer. For a new bobbin case (part code: XE7560-001), contact your nearest authorized service center. ● Make sure that you fit the bobbin case properly, otherwise the needle may break. ■ Checking machine operations If the needle plate has been removed, check machine operations to confirm that installation has been completed correctly. a Turn on the machine.
APPENDIX ———————————— — — —— — —— — —— — — —— — —— — —— — — —— — —— — —— —————————————————————————————————————————————————————————— ——————— — Correctly thread the machine. g • For details on threading the machine, refer to “Threading the upper thread” (page 20). Note ● The thread may have become tangled as a result of incorrect upper threading. Make sure that the machine is correctly threaded.
Slide the bobbin winder shaft to the left, and c then remove the bobbin from the shaft. Hold the thread end with your left hand, and d wind off the thread clockwise near the bobbin with your right hand as shown below. 4 e Wind the bobbin again. Note ● Make sure that the thread passes under the pretension disk of the bobbin-winding thread guide correctly (page 16).
APPENDIX ———————————— — — —— — —— — —— — — —— — —— — —— — — —— — —— — —— —————————————————————————————————————————————————————————— ——————— — List of symptoms Symptom The sewing machine does not operate. Probable Cause Remedy Insert the plug of the power cord into page 14 a household electrical outlet. The machine is not turned on. Turn on the machine. page 14 The bobbin winder shaft is moved to the right. Slide the bobbin winder shaft to the left. page 17 The presser foot lever is raised.
Symptom Probable Cause Remedy Reference The upper thread was incorrectly threaded (for example, the spool is incorrectly installed or the thread has Correct the upper threading. come out of the needle bar thread guide). page 20 There are knots or tangles in the thread. – Remove any knots or tangles. The selected needle is not Select a needle that is appropriate for page 28 appropriate for the thread being used. the type of stitch being used. The upper thread tension is too tight.
APPENDIX ———————————— — — —— — —— — —— — — —— — —— — —— — — —— — —— — —— —————————————————————————————————————————————————————————— ——————— — Symptom The thread tension is incorrect. The fabric is puckered. Stitches are skipped. Probable Cause Reference The upper thread is incorrectly installed. Correct the upper threading. page 20 The bobbin thread is incorrectly installed. Correct the bobbin threading. page 18 The bobbin thread is incorrectly wound. Correctly wind the bobbin.
Symptom The thread does not pass through the eye of the needle. The stitch is not sewn correctly. The fabric does not feed. Probable Cause Remedy Reference Press (needle position button) once or twice to raise the needle. page 21 The needle is incorrectly installed. Correctly install the needle. page 29 The presser foot appropriate for the type of stitch that you wish to sew is not used. Attach the presser foot that is appropriate for the type of stitch that you wish to sew.
APPENDIX —— — ——— — —— ———— ——— ——— ————— ——— ——————— ———————— ————— ——— ——— — ——— ——— — —— — —— ——— —— ——— ——— —— —— —— — —— ——— —— —— — —— — —— — — —— — ——— — Error Messages If the sewing machine is incorrectly operated or if the sewing machine malfunctions, an error message appears in the LCD. The message can be cleared by pressing any key in the operation panel, turning any dial, or performing the operation correctly. Error Code No.
Operation Beep Each time a key is pressed or an incorrect operation is performed, a beep is sounded. ■ For a correct operation One beep is sounded. ■ If an incorrect operation is performed Two or four beeps are sounded. ■ If the machine locks up, for example, because the thread is tangled The sewing machine continues to beep for three seconds, and then the machine automatically stops. Be sure to check for the cause of the error, and correct it before continuing to sew.
Index Numerics N 1/4 inch quilting foot......................................................12 1/4 inch quilting foot with guide ....................................12 needle ............................................................................ 27 needle plate cover.......................................................... 81 needle position............................................................... 53 needle position button....................................................18 needle set...
stretch stitching ..............................................................66 T thread guide ...................................................................20 thread tension ................................................................47 thread tension dial..........................................................47 triple stretch stitching .....................................................72 twin needle .............................................................11, 25 U upper thread.....
Please visit us at http://solutions.brother.com where you can get product support and answers to frequently asked questions (FAQs).
