IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic safety precautions should always be taken, including the following: Read all instructions before using. DANGER - To reduce the risk of electric shock: 1. The machine should never be left unattended while plugged in. Always unplug the machine from the electrical outlet immediately after using and before cleaning. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: 1.
FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY IMPORTANT • In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug. • Always replace the fuse cover. Never use plugs with the fuse cover omitted. • If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead.
Federal Communications Commission (FCC) Declaration of Conformity (For USA Only) Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA TEL : (908) 704-1700 declares that the product Product Name: Model Number: Brother Sewing Machine NX-2000 This device complies with Part 15 of the FCC Rules.
CONGRATULATIONS ON CHOOSING OUR MACHINE Your machine is the most advanced computerized household sewing machine. To fully enjoy all the features incorporated, we suggest that you study the manual. PLEASE READ BEFORE USING THIS MACHINE For safe operation 1. Be sure to keep your eye on the needle while sewing. Do not touch the handwheel, thread take-up lever, needle, or other moving parts. 2.
HOW TO USE THIS MANUAL Chapters 1 and 2 describe to the first-time user the initial operations for using this machine and the basic sewing operations. To sew utility stitches Continue with chapter 3 to learn how to select a stitch and sew using the various stitches.
CONTENTS NAMES OF MACHINE PARTS AND THEIR FUNCTIONS..........................................................9 Machine ..................................................................... 9 Needle and Presser Foot Section ............................... 10 Operation Buttons .................................................... 11 Included Accessories ................................................ 11 Options ....................................................................
Chapter 6 Appendix 137 CARE AND MAINTENANCE ..............................138 Cleaning the LCD .................................................... Cleaning the Machine Casing .................................. Cleaning the Race ................................................... Cleaning the Bobbin Case ....................................... 138 138 138 139 ADJUSTING THE SCREEN .................................140 1 Screen Visibility Is Low............................................
8
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Machine ■ Front View ■ Right-side/Rear View a Top cover a Handle Open the top cover to thread the machine and wind the bobbin. b Thread guide plate Pass the thread around the thread guide plate when threading the upper thread. c Thread take-up lever check window Look through the window to check the position of the take-up lever.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Needle and Presser Foot Section a Buttonhole lever Lower the buttonhole lever when sewing buttonholes and bar tacks. b Presser foot holder The presser foot is attached to the presser foot holder. c Presser foot holder screw Use the presser foot holder screw to hold the presser foot holder in place. d Presser foot The presser foot consistently applies pressure to the fabric as it is sewn. Attach the appropriate presser foot for the selected stitch.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Operation Buttons Included Accessories The accessories are stored in the flat bed attachment. Open the flat bed attachment as shown below. a “Start/Stop” button When this button is pressed, the machine sews a few stitches at a low speed, then begins sewing at the speed set by the sewing speed controller. Press this button again to stop sewing. This button lights up in a different color depending on the machine’s operating condition.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS 1 8 9 16 17*1 22 23 2 3 4 5 6 7 10 11 12 13 14 15 18 19 20 21 24 25 26 27 75/11 2 needles 90/14 2 needles 90/14 2 needles: Ball point needle (gold colored) 2.0/11 needle 28 29 30 31 32 33 34 35 36 37 38*2 39 40 41 42 43 44 *1 See Circular Attachment Instruction Manual for detailed instruction. *2 See Bobbin Work Instruction Manual for detailed instruction.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Part Code No. Part Name U.S.A./ Canada Memo Others 1 Buttonhole foot “A” X57789-151 2 Overcasting foot “G” XC3098-051 (For U.S.A. only) Foot controller: Model T This foot controller can be used with this machine model NX-2000.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Options 1 2 3 4 Part Code No. Part Name U.S.A./ Canada Others 1 Quilting foot SA129 F005N 2 1/4” quilting foot SA125 F001N 3 Side cutter foot SA177 F054 4 Spool stand SA542 TS3 Memo • All specifications are correct at the time of printing. • Please be aware that some specifications may change without notice. Note Visit your authorized dealer for complete listing of optional accessories available for your machine.
1 Chapter 1 Getting Ready TURNING THE MACHINE ON/OFF....................................................16 LCD SCREEN........................................................................................17 ■ Display Precautions.........................................................................................................17 ■ Key Functions ..................................................................................................................18 Using the Machine Setting Mode Key...
TURNING THE MACHINE ON/OFF TURNING THE MACHINE ON/OFF WARNING • Use only regular household electricity as the power source. Using other power sources may result in fire, electric shock, or damage to the machine. • Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power supply jack on the machine. • Do not insert the plug on the power cord into an electrical outlet that is in poor condition.
LCD SCREEN LCD SCREEN ■ Display Precautions 1 Getting Ready • Only touch the display with your finger or the touch pen included with the machine. Do not use a mechanical pencil, screwdriver or any other hard or sharp objects. In addition, do not press the display with extreme pressure, otherwise damage to the display may result. • All or part of the display may sometimes become darker or lighter due to fluctuations in the surrounding temperature or other changes in the environment.
LCD SCREEN ■ Key Functions With your finger or the touch pen, press a key at the top of the display ( screen that is displayed. 1 2 ) to change the 3 5 4 h g f i j k l q m n o r p s Operation panel No. 18 Key Name Function Page 1 Machine setting mode key Press this key to change the needle stop position, turn the buzzer on/off, adjust the pattern or screen, and change other machine settings.
LCD SCREEN Screen No. f Key Name Drop feed key Function Page For free-motion sewing, press this key to lower the feed dogs (free-motion sewing 75, 94 mode). In addition, the key automatically appears as and the feed dogs are lowered when button sewing is selected. Screen lock key Press this key to lock the screen. When the screen is locked, the various settings, such as the stitch width and stitch length, are locked and cannot be changed. Press this key again to unlock the settings.
LCD SCREEN Using the Machine Setting Mode Key Press to change the needle stop position, turn the buzzer on/off, adjust the pattern or screen, and change other basic machine settings. The settings specified here are the default settings. Press to display the previous or next page. a Select whether the needle stops in the raised or lowered position when the machine is stopped. b Select whether to use the sewing speed controller or to adjust the zigzag width (see page 74).
LCD SCREEN Using the Machine Operation Mode Key Basic machine operations and other information based on the contents of this Operation Manual are stored in this machine. Press to open the screen shown below. Six categories are displayed at the top of the screen. Press a key to see more information about that category.
LCD SCREEN Example: a Displaying information about upper threading Press Using the Pattern Explanation Key . Press b . → A list of basic operations appears in the lower half of the screen. To learn more about the uses for a stitch, select the stitch, and then press selected stitch. Example: c Press to see a description of the Displaying information on the use for (upper threading). . a Select , and then press . → The instructions for threading the machine appear.
LOWER/UPPER THREADING LOWER/UPPER THREADING c Winding the Bobbin Set the supplemental spool pin in the “up” position. a CAUTION • The included bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB: XA5539-051). Actual size 11.5 mm (approx. 7/16 inch) 1 Getting Ready This section describes how to wind thread onto a bobbin.
LOWER/UPPER THREADING e While holding the thread from the spool in your right hand, hold the end of the thread with your left hand, and then pass the thread through the thread guide. i Slide the bobbin holder to the left until it snaps into place. * When the bobbin holder is set to the left, it works as a switch to make the bobbin wind automatically. a a a Bobbin holder (switch) → The bobbin stops spinning automatically when it is full, and the bobbin holder returns to its original position.
LOWER/UPPER THREADING ■ Winding the Bobbin Using the Spool Pin The main spool pin cannot be used to wind the bobbin while sewing. For details, see “Using the Supplemental Spool Pin” on page 23. 2 8 Slide the spool cap as far as possible onto the spool pin, and then return the spool pin to its original position. f While holding the thread from the spool with both hands, pull the thread through the lower notch in the thread guide plate, then through the upper notch.
LOWER/UPPER THREADING Setting the Bobbin e Lightly hold down the bobbin with your right hand, and then, while slightly pulling the thread with your left hand, guide it through the groove. f After guiding the thread completely through the groove, pull it toward you to cut it with the cutter. This section describes how to set a bobbin wound with thread into the machine. You can begin sewing without pulling up the bobbin thread.
LOWER/UPPER THREADING b Guide the bobbin thread through the groove, following the arrow in the illustration. Note • Do not cut the thread with the cutter. • Do not attach the bobbin cover. Upper Threading This section describes how to thread the machine and the needle. The machine is marked with numbers that indicate the threading order. c While lightly holding the upper thread, press the “Needle Position” button twice to lower, then raise the needle. • Be sure to thread the machine properly.
LOWER/UPPER THREADING c Press the “Needle Position” button to raise the needle. g While holding the thread from the spool in your right hand, hold the end of the thread with your left hand, and then guide the thread through the groove, following the arrows in the illustration. h Guide the thread down, up, then down through the groove, as shown in the illustration. Note If you try to thread the needle with the needle threader lever without raising it, damage to the machine may result.
LOWER/UPPER THREADING j Pass the thread through the thread guide disks (marked “7”). * Make sure that the thread passes through the groove in the thread guide. * Make sure that the thread securely enters the thread guide disks, otherwise the needle may not be threaded. m n Release the needle threader lever. → The thread passes through the eye of the needle. Carefully pull the end of thread that was passed through the eye of the needle. Do not pull the thread strongly.
LOWER/UPPER THREADING Using the Twin Needle c Using the twin needle, you can sew two parallel lines of the same stitch. Although the same bobbin thread is used, interesting patterns can be sewn by threading each needle with a different color of thread. Both upper threads should have the same thickness and quality. The twin needle can only be used with patterns where Pass the thread through the needle bar thread guide, and then manually thread the needle on the left side.
LOWER/UPPER THREADING g While holding the thread from the spool with both hands, pull the thread through the lower notch in the thread guide plate, then through the upper notch. Hold the end of the thread with your left hand, and then guide the thread through the groove, following the arrows in the illustration. k Press to select the setting for twin needle sewing. * The stitch width becomes narrower than with single needle sewing. a 1 Getting Ready a a Single needle/twin needle setting → appears.
CHANGING THE PRESSER FOOT CHANGING THE PRESSER FOOT CAUTION • Always press in the operation panel before changing the presser foot. If is not pressed and the “Start/Stop” button or another button is pressed, the machine will start and may cause injury. • Always use the correct presser foot for the selected stitch. If the wrong presser foot is used, the needle may strike the presser foot and bend or break, and may cause injury. • Only use presser feet made for this machine.
CHANGING THE NEEDLE CHANGING THE NEEDLE CAUTION in the operation panel before changing the needle. If is not pressed and the “Start/ Stop” button or another operation button is pressed accidentally, the machine will start and injury may result. • Use only sewing machine needles made for home use. Other needles may bend or break and may cause injury. • Never sew with a bent needle. A bent needle will easily break and may cause injury.
CHANGING THE NEEDLE c Use the included screwdriver to turn the needle clamp screw toward the front of the machine to loosen it, and then remove the needle. Note Do not apply extreme force when loosening or tightening the needle clamp screw, otherwise damage to the machine may result. d With the flat side of the needle facing the back, insert the new needle until it touches the needle stopper. Use the screwdriver to securely tighten the needle clamp screw.
CHANGING THE NEEDLE ■ About the Needle ■ Fabric/Thread/Needle Combinations 1 Getting Ready The sewing machine needle is probably the most important part of the sewing machine. Choosing the proper needle for your sewing project will result in a beautiful finish and fewer problems. Below are some things to keep in mind about needles. • The smaller the needle number, the finer the needle. As the numbers increase, the needles get thicker.
SEWING LARGE PIECES OF FABRIC SEWING LARGE PIECES OF FABRIC The wide table makes sewing large pieces of fabric easier. d When you are finished using the wide table, remove it. While slightly lifting up the wide table, pull it off to the left. CAUTION • Do not move the sewing machine while the wide table is attached, otherwise damage or injuries may occur. • Do not use the wide table for other purposes such as an ironing board. This can cause damage and injury.
2 Chapter 2 Sewing Basics SEWING ..............................................................................................38 Sewing a Stitch........................................................................................................38 ■ Using the Foot Controller................................................................................................39 ■ Using the Knee Lifter.......................................................................................................
SEWING SEWING CAUTION • To avoid injury, pay special attention to the needle while the machine is in operation. Keep your hands away from moving parts while the machine is in operation. • Do not stretch or pull the fabric during sewing. Doing so may lead to injury. • Do not use bent or broken needles. Doing so may lead to injury. • Take care that the needle does not strike basting pins or other objects during sewing. Otherwise, the needle may break and cause injury.
SEWING h To stop sewing, press the “Start/Stop” button again. ■ Using the Foot Controller You can also use the foot controller to start and stop sewing. CAUTION • Do not allow fabric pieces and dust to collect in the foot controller. Doing so could cause a fire or an electric shock. i Press the “Thread Cutter” button to trim the threads. Insert the foot controller plug into its jack on the machine. Sewing Basics When the foot controller is being used, the “Start/Stop” button has no effect on sewing.
SEWING ■ Using the Knee Lifter Using the knee lifter, you can raise and lower the presser foot with your knee, leaving both hands free to handle the fabric. a Align the tabs on the knee lifter with the notches in the jack, and then insert the knee lifter as far as possible. Sewing Reinforcement Stitches Generally stitching must be secured at the beginning and end with reverse/reinforcement stitches. Press the “Reverse/Reinforcement Stitch” button to sew reverse/ reinforcement stitches.
SEWING Changing Sewing Direction Stop the machine with the needle in the fabric at the point where you want to change the sewing direction, and then raise the presser foot lever. Using the needle as a pivot, turn the fabric, lower the presser foot lever, and then continue sewing. a Raise the presser foot lever. b While keeping the black button on the left side of presser foot “J” pressed in, lower the presser foot lever. 2 The pivot setting is useful when changing the sewing direction.
ADJUSTING STITCH SETTINGS ADJUSTING STITCH SETTINGS When a stitch is selected, the most appropriate stitch width, stitch length, and upper thread tension are automatically set. However, if needed, you can change any of the settings as described in this section. Note • Settings for some stitches cannot be changed (See “STITCH SETTING CHART” at the end of this manual).
USEFUL FUNCTIONS Adjusting the Thread Tension The default thread tension, which is automatically set, can normally be used regardless of the type of thread or fabric being sewn. However, with some fabric and thread combinations, the thread tension may need to be adjusted. ■ Upper Thread Is Too Tight If the bobbin thread can be seen on the surface of the fabric, press . Each press of the key reduces the setting and decreases the upper thread tension.
USEFUL FUNCTIONS c Place the fabric under the presser foot with the needle at the starting point of the stitching, and then press the “Start/Stop” button. The machine will automatically sew reverse stitches (or reinforcement stitches), and then begin sewing. b Press to select the automatic thread cutting setting.
USEFUL FUNCTIONS d If the “Reverse/Reinforcement Stitch” button is pressed, the machine automatically sews reverse stitches (or reinforcement stitches), cuts the thread, then stops. Pivoting If the pivot setting is selected, the machine stops with the needle lowered (in the fabric) and the presser foot is automatically raised to an appropriate height when the “Start/Stop” button is pressed. When the “Start/Stop” button is pressed again, the presser foot is automatically lowered and sewing continues.
USEFUL FUNCTIONS a Select a stitch. b Press e to select the pivot setting. Rotate the fabric, and then press the “Start/ Stop” button. → The presser foot is automatically lowered, and sewing continues. Automatic Fabric Sensor System → The key appears as c . Place the fabric under the presser foot with the needle at the starting point of the stitching, and then press the “Start/Stop” button. The machine will begin sewing.
USEFUL FUNCTIONS b Press to display P. 2, and then set the “AUTOMATIC FABRIC SENSOR SYSTEM” to “ON”. Locking the Screen If the screen is locked before starting to sew, the various settings, such as the stitch width and stitch length, are locked and cannot be changed. This prevents screen settings from accidentally being changed or the machine from being stopped while large pieces of fabric or other projects are being sewn.
USEFUL FUNCTIONS 48
3 Chapter 3 Utility Stitches SELECTING A UTILITY STITCH ...........50 Blind Hem Stitches ...........................................79 ■ Stitch Selection Screens ....................................... 50 ■ If the Needle Does Not Catch the Fold.................80 ■ If the Needle Catches Too Much of the Fold ........80 Selecting a Stitch .............................................. 51 Appliqués..........................................................80 ■ Using the Mirror Image Key ..............
SELECTING A UTILITY STITCH SELECTING A UTILITY STITCH ■ Stitch Selection Screens Press to display the previous or next page.
SELECTING A UTILITY STITCH Selecting a Stitch a Saving Stitch Settings Turn on the machine, and then lightly press the display. → Depending on the setting, either “Q-01 Piecing stitch (Middle)”, “1-01 Straight stitch (Left)” or “1-03 Straight stitch (Middle)” is automatically selected. This machine is preset with the default settings for the stitch width (zigzag width), stitch length, thread tension, automatic thread cutting, automatic reverse/ reinforcement stitching, etc.
SELECTING A UTILITY STITCH Using the Sewing Type Selection Key Memo • The next time that the same straight stitch is selected, the stitch length is set to 2.0 mm. • All stitch settings (stitch width, stitch length, thread tension, automatic thread cutting, automatic reverse/reinforcement stitching, mirror image, and twin needle settings) are saved, not just the setting that was changed. When the same stitch is selected, the last settings saved are displayed even if the machine was turned off.
SELECTING A UTILITY STITCH Example: a Press Displaying information about piecing. c Select a stitch. * Press . to return to the previous screen. 3 b Press . d Utility Stitches → Directions for sewing the selected stitch are displayed. → The sewing type selection screen is displayed. Follow the directions to sew the stitch. * Press or to scroll the page. * Press to display the next page. * Press to return to the previous screen. → The stitch selection screen for piecing is displayed.
SEWING THE STITCHES SEWING THE STITCHES Straight Stitches Note When using the twin needle (see page 30), be sure to attach presser foot “J”. Stitch Key Stitch Name Presser Foot Stitch width [mm (inch)] Applications Stitch length [mm (inch)] Twin Needle Auto Manual Auto Manual General sewing, gather, pintuck, etc. Reverse stitch is sewn while pressing “Reverse/ Reinforcement Stitch” button. 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.
SEWING THE STITCHES a Select a stitch. c Hold the thread ends and the fabric with your left hand, and turn the handwheel toward you with your right hand to insert the needle into the fabric at the starting point of the stitching. At the end of the stitching, hold the “Reverse/ Reinforcement Stitch” button pressed to sew reverse stitches (or reinforcement stitches). g Press the “Thread Cutter” button to trim the threads.
SEWING THE STITCHES ■ Changing the Needle Position (Left or Middle Needle Position Stitches Only) ■ Basting When you select left or middle (center) needle position stitches, you can use and in the stitch width display to change the position of the needle. Match the distance from the right edge of the presser foot to the needle with the stitch width, then align the edge of the presser foot with the edge of the fabric during sewing for an attractive finish.
SEWING THE STITCHES ■ Aligning the fabric with the seam guide This adjustable screw-on seam guide helps you to sew an accurate 6.5mm,13mm or 16 mm (approx. 1/4,1/2 or 5/8 inch) seam from the edge of the fabric. a d Guide the right edge of a fabric lightly against the seam guide with your hands while sewing. Select a straight stitch with the middle (center) needle position (Ex. , ). Note Select the straight stitch with the middle needle position.
SEWING THE STITCHES d Grasp the bobbin case, and then pull it out. g Insert the bobbin case so that the ▲ mark aligns with the ● mark as shown below, and then attach the needle plate cover. a a Bobbin case b Use the disc-shaped screwdriver included e with the machine to unscrew and remove the regular needle plate. a b a ▲ mark b ● mark * Align the ▲ and ● marks. h f Set the straight stitch needle plate in place and use the screwdriver to tighten the plate.
SEWING THE STITCHES j Start sewing. Darts Seams * After sewing, make sure to remove the straight stitch needle plate and the straight stitch foot, and reinstall the regular needle plate, the needle plate cover and the presser foot “J”. a Press Memo b Press the “Reverse/Reinforcement Stitch” button to sew reverse stitches at the beginning of the stitching, and then sew from the wide end to the narrow end without stretching the fabric.
SEWING THE STITCHES Gathering e Pull the bobbin threads to create the desired amount of gathering, and then tie the threads. f Smooth the gathers by ironing them. g Sew along the seam line, and then remove the basting stitch. Sew gathers on sleeves, the waist of a gathered skirt, etc. a b Select a straight stitch, and then attach presser foot “J”. Set the stitch length to 4.0 mm (approx. 3/16 inch) and the thread tension to 2.0 (weaker tension).
SEWING THE STITCHES d Lay both seam allowances on the side of the shorter one (cut seam allowance) and iron them flat. Pintucks Use pin tucks to decorate blouses. a a Mark the positions of the folds on the wrong side of the fabric. a Wrong side of fabric e a Fold the longer seam allowance around the shorter one, and then sew along the edge of the fold. a Wrong side of fabric b a Turn the fabric over, and then iron only the folds with the tip of the iron.
SEWING THE STITCHES Zigzag Stitches Zigzag stitches are useful for a variety of applications, including overcasting and sewing appliqués and patchwork. Note When using the twin needle (see page 30), be sure to attach presser foot “J”. Stitch Key Stitch Name Zigzag stitch (Middle) Zigzag stitch (Middle) a Presser Foot Stitch width [mm (inch)] Applications Stitch length [mm (inch)] Twin Needle Auto Manual Auto Manual For overcasting, mending.
SEWING THE STITCHES ■ Patchwork (Crazy Quilts) Turn back the desired width of seam allowance, place it over a different piece of fabric, and then sew the two fabric pieces together so the stitching bridges both pieces. ■ Sewing Curves 3 Utility Stitches Shorten the stitch length setting to obtain a fine stitch. Sew slowly, keeping the seams parallel with the fabric edge as you guide the fabric around the curve.
SEWING THE STITCHES Elastic Zigzag Stitches Use elastic zigzag stitches for a wide variety of applications, including overcasting, tape attaching, and darning. Stitch Key a Stitch Name Presser Foot Applications Stitch width [mm (inch)] Auto Stitch length [mm (inch)] Twin Needle Manual Auto Manual 2 step elastic zigzag For overcasting (medium weight 5.0 and stretch fabrics), attaching (3/16) tape and elastic 1.5 - 7.0 (1/16 - 1/4) 1.0 (1/16) 0.2 - 4.
SEWING THE STITCHES Overcasting Sew overcasting at the beginning and end of seams for skirts or pants, and at the beginning and end of all cuttings. Depending on the selected stitch, use presser foot “G” or “J” or the optional side cutter attachment.
SEWING THE STITCHES ■ Overcasting Using Presser Foot “J” Stitch Key Stitch Name Presser Foot Overcasting stitch Reinforced seaming of stretch fabric Overcasting stitch Reinforcing of medium stretch fabric and heavyweight fabric, decorative stitching Overcasting stitch Reinforcement of stretch fabric or decorative stitching Overcasting stitch Stretch knit seam Stitch length [mm (inch)] Twin Needle Auto Manual Auto Manual 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.5 - 4.
SEWING THE STITCHES ■ Overcasting Using the Optional Side Cutter By using the side cutter, you can do overcasting while cutting the fabric. CAUTION • Make sure to only select one of the stitches listed below. Using another stitch may cause the needle to hit the presser foot and break, possibly causing injury. Memo Thread the needle manually when using the side cutter, or only attach the side cutter after threading the needle using the needle threader.
SEWING THE STITCHES d h Select a stitch. Start sewing. → A seam allowance is cut while the stitching is sewn. Note e Make a cut of approximately 20 mm (approx. 3/4 inch) in the fabric. If the width has been adjusted, turn the handwheel by hand to check that the needle does not touch the side cutter. If the needle touches the side cutter, it might cause the needle to break. ■ When Sewing Straight Stitches While Using the Optional Side Cutter The seam margin should be approximately 5 mm (approx.
SEWING THE STITCHES Quilting You can make beautiful quilts quickly and easily with this machine. When making a quilt, you will find it convenient to use the knee lifter and foot controller to free your hands for other tasks (see “Using the Foot Controller” on page 39 and/or see “Using the Knee Lifter” on page 40). The 30 quilting stitches Q-01 through Q-30 and the utility stitches with “P” or “Q” indicated on their key are useful for quilting.
SEWING THE STITCHES Stitch Key Stitch Name Stitch width [mm (inch)] Applications Stitch length [mm (inch)] Twin Needle Auto Manual Auto Manual 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 4.0 (3/16) 1.0 - 4.0 (1/16 - 3/16) NO 5.5 (7/32) 0.0 - 7.0 (0 - 1/4) 1.4 (1/16) 0.2 - 4.0 (1/61 - 3/16) NO 5.0 (3/16) 1.5 - 7.0 (1/16 - 1/4) 2.0 (1/16) 0.2 - 4.0 (1/64 - 3/16) NO 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 1.0 - 4.0 (1/16 - 3/16) NO 5.0 (3/16) 2.5 - 7.0 (3/32 - 1/4) 2.5 (3/32) 1.0 - 4.
SEWING THE STITCHES Stitch Key Presser Foot Stitch Name Hand-look quilting Stitch width [mm (inch)] Applications Quilting stitch made to look like hand quilting stitch Quilting appliqué zigzag stitch Zigzag stitch for quilting and sewing on appliqué quilt pieces Quilting appliqué stitch Quilting stitch for invisible appliqué or attaching binding Quilting stippling Background quilting Stitch length [mm (inch)] Twin Needle Auto Manual Auto Manual 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.
SEWING THE STITCHES b Use the guide and marks on the presser foot to sew accurate seam allowances. Topstitching quilting, 1/8 inch Sew with the edge of the fabric aligned with the left side of the presser foot end. Piecing a 1/4 inch seam allowance Sew keeping the edge of the fabrics against the guide. a b b c a Surface of fabric b Seam c 1/8 inch a a Guide b 1/4 inch ■ Quilting Using Walking Foot Memo For accurate fabric placement, refer to “Needle Plate and Needle Plate Cover Marks” on page 56.
SEWING THE STITCHES d Lower the presser foot lever. Tighten the screw securely with the screwdriver. Presser foot holder b e Adjust the stem of the quilting guide so that the guide aligns with the seam that has already been sewn. Place one hand on each side of the walking foot to hold the fabric secure while sewing. Note 3 ■ Appliqués The seam will blend in if transparent nylon thread is used for the upper thread. a Trace the pattern onto the appliqué fabric, and then cut around it.
SEWING THE STITCHES e Check the needle drop point, and then sew along the edge of the appliqué while making sure that the needle drops slightly off the edge of the fabric. e Set “WIDTH CONTROL” to “ON”. The sewing speed will be adjusted using the foot controller. f Press g While sewing, slide the sewing speed controller to adjust the stitch width. a a Needle drop point CAUTION • Be careful that the needle does not strike a basting pin during sewing.
SEWING THE STITCHES ■ Free-motion Quilting For free-motion quilting, use free-motion quilting foot “C” and free-motion open toe quilting foot “O” depending on the stitch that is selected, and set the machine to free-motion sewing mode. In this mode, the feed dogs are automatically lowered so the fabric can be moved freely, and the presser foot is raised to the necessary height for free-motion sewing. a Press to lower the feed dogs and to set the machine to free-motion sewing mode.
SEWING THE STITCHES f Use both hands to stretch the fabric taut, and then move the fabric at a regular pace in order to sew uniform stitches roughly 2.0-2.5 mm (approx. 1/16 - 3/32 inch) in length. a Press to lower the feed dogs and to set the machine to free-motion sewing mode. a a Stitch Note Before beginning to do free-motion embroidery, follow the directions on page 27 for pulling up the bobbin thread. Grasp the upper and lower threads and sew a few stitches to lock threads.
SEWING THE STITCHES e Hold the quilting foot in place with your right hand, and then tighten the presser foot holder screw using the screwdriver in your left hand. a Presser foot holder screw ■ Echo Quilting Sewing quilting lines at equal distances around a motif is called echo quilting. The quilting lines, which appear as ripples echoing off the motif, are the distinguishing characteristic of this quilting style. Use the free-motion echo quilting foot “E” for echo quilting.
SEWING THE STITCHES a b Press to lower the feed dogs and to set the machine to free-motion sewing mode. f Tighten the screw. g Using the measurement on the quilting foot as a guide, sew around the motif. Select a straight stitch with the middle (center) needle position or . c Follow the steps on page 32 “Removing the Presser Foot” to remove the presser foot. d Loosen the presser foot holder screw, and then remove the screw and the presser foot holder. a 6.4 mm (approx.
SEWING THE STITCHES Blind Hem Stitches Select a blind hem stitch to sew the hems or cuffs of dresses, blouses, pants, or skirts. Stitch Key Presser Foot Stitch Name Blind hem stitch c Twin Needle Manual Auto Manual 00 3← − →3 2.0 (1/16) 1.0 - 3.5 (1/16 - 1/8) NO 00 3← − →3 2.0 (1/16) 1.0 - 3.5 (1/16 - 1/8) NO Hemming stretch fabric Select a stitch.
SEWING THE STITCHES f Remove the basting, and then turn over the fabric. Appliqués a a b Use a temporary spray adhesive or basting to attach the appliqué to the fabric. a a Wrong side of fabric b Surface of fabric b Memo Blind hem stitches cannot be sewn if the needle does not catch the fold on the left side. However, if the needle catches too much of the fold, the fabric cannot be unfolded and too much of the seam will appear on the surface of the fabric, leaving an unattractive finish.
SEWING THE STITCHES ■ Sewing Sharp Curves Stop the machine with the needle in the fabric outside the appliqué. Raise the presser foot and turn the fabric a little bit at a time while sewing for an attractive finish to the seam. The pivot setting is useful when changing the sewing direction. When the machine is stopped at the corner of the fabric, the machine stops with the needle in the fabric and the presser foot is automatically raised so the fabric can easily be rotated (see “Pivoting” on page 45).
SEWING THE STITCHES b Leave a seam when sewing the scallop stitches so that the pattern is not sewn directly on the edge of the fabric. c Turn the fabric over so the right side faces up, and then sew over the seam with the center of the presser foot aligned with the seam. * Select one of the following stitches. Note Sew test stitches on the fabric before sewing on your project. a a Surface of fabric c Trim along the seam, making sure not to cut the stitches.
SEWING THE STITCHES e Pull the bobbin threads to create the desired amount of gather, and then smooth the gathers by ironing them. Fagoting Stitching across an open seam is called fagoting. It is used on blouses and children’s clothing. a Separate the two pieces of fabric by about 4 mm (approx. 3/16 inch), and baste them onto thin paper. a f Press or b . c Memo 3 For details on the stitches, refer to the “STITCH SETTING CHART” at the end of this manual. Sew between the straight stitches.
SEWING THE STITCHES Tape or Elastic Attaching f Press or . Elastic tape is sewn onto the fabric unstretched. Memo Select a straight stitch, and then attach a presser foot “J”. For details on the stitches, refer to “Stitch Setting Chart” at the end of this manual. g Note Make sure that the automatic reverse/reinforcement stitching and automatic thread cutting settings are not selected. b Set the stitch length to 4.0 mm (approx. 3/16 inch) and the thread tension to 2.0 (weaker tension).
SEWING THE STITCHES Heirloom Stitching By sewing with a wing needle sold separately, the needle holes are enlarged, creating a lace-like decorative stitch. This stitching is used to decorate tablecloths, hems, and shirt fronts. b Select a stitch, attach presser foot “N”, and then start sewing. * Select a stitch between 3-01 and 3-22. Drawn Work (1 ■ Hemstitching (1) (Daisy Stitch) 3 For best results, use lightweight to medium weight homespun fabrics with a slight stretch.
SEWING THE STITCHES a Pull out several threads from the fabric to leave a 3 mm (approx. 1/8 inch) area open. ■ Hemstitching (3) (Drawn Work (2)) Memo For best result, use loosely woven fabrics. Memo Drawn work can also be sewn using the wing needle (sold separately). a b Press , and then attach presser foot “N”. Pull out several threads from both sides of a 4 mm (approx. 3/16 inch) area left unopened, as shown in the illustration.
SEWING THE STITCHES Buttonhole Stitches Select the desired buttonhole stitch according to your application and the size of the button. Stitch Key Stitch Name Presser Foot Stitch width [mm (inch)] Applications Stitch length [mm (inch)] Twin Needle Manual Auto Manual 5.0 (3/16) 3.0 - 5.0 (1/8 - 3/16) 0.4 (1/64) 0.2 - 1.0 (1/64 - 1/16) NO 5.5 (7/32) 3.5 - 5.5 (1/8 - 7/32) 0.4 (1/64) 0.2 - 1.0 (1/64 - 1/16) NO 5.0 (3/16) 3.0 - 5.0 (1/8 - 3/16) 0.4 (1/64) 0.2 - 1.0 (1/64 - 1/16) NO 5.
SEWING THE STITCHES a Select a stitch, and then attach presser foot “A”. b Mark the position and length of the buttonhole on the fabric. d Hold the outside frame of the buttonhole foot toward the back with your finger, and then lower the presser foot so that the mark on the fabric aligns with the marks on the buttonhole foot. Memo a The maximum buttonhole length is 28 mm (approx. 11/6 inches) (diameter + thickness of the button).
SEWING THE STITCHES f Gently hold the end of the upper thread, and then start sewing. * Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. * If the automatic thread cutting setting is selected before sewing, the machine will automatically cut the thread at the end of stitching. g Insert a pin along the inside of a bar tack at the end of the buttonhole, and then insert the seam ripper into the center of the buttonhole and cut towards the pin.
SEWING THE STITCHES ■ Sewing Stretch Fabrics When sewing a buttonhole on stretch fabrics, press or a , and use a gimp thread. Hook the gimp thread onto the back of buttonhole foot “A”, and then pull the ends of the gimp thread under the presser foot. Pass the thread ends through the grooves at the front of the presser foot, and then temporarily tie them. ■ Buttons That Do Not Fit into the Button Holder Plate Use the markings on the presser foot scale to set the size of the buttonhole.
SEWING THE STITCHES ■ Darning Use darning stitches for mending and other applications. Stitch Key Presser Foot Stitch Name Stitch width [mm (inch)] Applications Darning of medium weight fabric Darning Darning Darning of heavyweight fabric Stitch length [mm (inch)] Twin Needle Auto Manual Auto Manual 7.0 (1/4) 2.5 - 7.0 (3/32 - 1/4) 2.0 (1/16) 0.4 - 2.5 (1/64 - 1/16) NO 7.0 (1/4) 2.5 - 7.0 (3/32 - 1/4) 2.0 (1/16) 0.4 - 2.
SEWING THE STITCHES d e Pull down the buttonhole lever. * The buttonhole lever should be positioned behind the metal bracket on the buttonhole foot, as shown in the illustration. a Gently hold the end of the upper thread, and then start sewing. * Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. * If the automatic thread cutting setting is selected before sewing, the machine will automatically cut the thread at the end of stitching.
SEWING THE STITCHES c Position the fabric so that the opening of the pocket moves toward you during sewing. Hold the outside frame of the buttonhole foot toward the back with your finger, check the first needle drop point, and then lower the presser foot. e Gently hold the end of the upper thread, and then start sewing. * Once sewing is completed, the machine automatically sews reinforcement stitches, then stops.
SEWING THE STITCHES Button Sewing Buttons with 2 or 4 holes can be sewn on. Note Make sure that the automatic thread cutting setting is not selected when sewing on buttons. Stitch Key Presser Foot Stitch Name Button sewing a Press → Stitch width [mm (inch)] Applications Attaching buttons e . automatically changes to dogs are lowered. Stitch length [mm (inch)] Auto Manual Auto Manual 3.5 (1/8) 2.5 - 4.
SEWING THE STITCHES ■ Attaching a 4-Hole Button Sew the two holes toward the front. Then, raise the presser foot, move the fabric so that the needle goes into the back two holes, and then sew them in the same way. b When sewing is finished, pull the two ends of the upper thread between the button and the fabric, wind them around the shank, and then tie them together.
SEWING THE STITCHES d Use the eyelet punch to cut a hole in the center of the stitching. c Press , and then attach presser foot “N”. Multi-Directional Sewing (Straight Stitch and Zigzag Stitch) Memo Use these stitches to attach patches or emblems to pant legs, shirt sleeves, etc. Memo Pass the free-arm through the tubular piece of fabric, and then sew in the order shown in the illustration. For details on the stitches, refer to the “STITCH SETTING CHART” at the end of this manual.
SEWING THE STITCHES g Press , and then sew seam 4. c * The fabric will move sideways, so guide the fabric with your hands to sew straight. Press open the seam allowance, align the seam with the center of the zipper, and then baste the zipper in place. b a a c a Wrong side of fabric b Basting c Zipper teeth Memo Zigzag stitches can also be used with multi-directional sewing.
SEWING THE STITCHES ■ Side Zipper Use for side zippers on skirts or dresses. a Press d . Remove presser foot “J”, and then attach the presser foot holder to the pin on the right side of zipper foot “I”. a * Be sure to select the straight stitch with the middle (center) needle position. c b a Right side b Left side c Needle drop point CAUTION b Attach presser foot “J”, sew straight stitches to the zipper opening, and then sew basting stitches to the edge of the fabric.
SEWING THE STITCHES h Close the zipper, turn the fabric over so that the surface faces up, and then baste the other side of the zipper to the fabric. c a b d a b c d i Front of garment (wrong side of fabric) Back of garment (surface of fabric) Basting Front of garment (surface of fabric) a c 3 Utility Stitches Remove the presser foot, and then attach the pin on the left side of the zipper foot to the presser foot holder.
SEWING THE STITCHES 100
4 Chapter 4 Character/ Decorative Stitches SELECTING STITCH PATTERNS.........................................................102 ■ Stitch Selection Screens ........................................................................................................ 102 Selecting Decorative Stitch Patterns/7 mm Decorative Stitch Patterns/Satin Stitch Patterns/ 7 mm Satin Stitch Patterns/Cross Stitch Patterns/Utility Decorative Stitch Patterns ............103 Alphabet Patterns.................................
SELECTING STITCH PATTERNS SELECTING STITCH PATTERNS ■ Stitch Selection Screens Press b e h to display the screen shown below.
SELECTING STITCH PATTERNS Selecting Decorative Stitch Patterns/ 7 mm Decorative Stitch Patterns/ Satin Stitch Patterns/ 7 mm Satin Stitch Patterns/Cross Stitch Patterns/Utility Decorative Stitch Patterns a Press c To combine patterns, select the next pattern. * Press to check the selected pattern combination. * If the wrong pattern was selected, press to erase the pattern, and then select the new stitch pattern. , and then press the key for the category containing the pattern that you want to sew.
SELECTING STITCH PATTERNS b Press to display a selection b Press . c Press . d Press , then screen of characters, and then select a character. Repeat this step until you have selected all of the characters. * If a wrong character was selected, press to erase the character, and then select the new character. * To select a different character style, press , and then select the new character style. * Press to check the selected characters.
SEWING STITCH PATTERNS SEWING STITCH PATTERNS Sewing Attractive Finishes Note • To achieve the best results when sewing character/decorative stitches, check the table below for the proper fabric/ needle/thread combinations. • Other factors, such as the type or thickness of the fabric being sewn or the type of stabilizer material used, also affect the stitching. Therefore, be sure to sew a few trial stitches before sewing your project.
SEWING STITCH PATTERNS e Press the “Start/Stop” button to stop the machine, and then press the “Reverse/ Reinforcement Stitch” button to sew reinforcement stitches. Adjusting Patterns Depending on the type and thickness of the fabric being sewn, the sewing speed, whether or not stabilizer material is used, etc., the desired result may not be achieved. If this occurs, sew , and then perform the following adjustment using the same sewing conditions as those used for your project.
SEWING STITCH PATTERNS d Press . e Sew the pattern again. If the pattern still is not sewn correctly, adjust it again. Continue making adjustments until the pattern is sewn correctly. Memo You can sew with the settings screen on the display. f After the pattern is sewn correctly, quit making adjustments. Press to return to the previous screen. Note The adjustment made will remain until changed again. If the pattern is bunched together: If the pattern is stretched: Press in the FINE ADJUST VERTI.
EDITING STITCH PATTERNS EDITING STITCH PATTERNS Using the editing functions, you can change the patterns in a variety of ways, such as resizing them or flipping them to create a mirror image. Memo Depending on the pattern that is selected, some editing functions may not be available. a b g f e c d j n o h i m k l ■ Key Functions No. 108 Key Name Function Page 47 a Screen lock key Press this key to lock the screen.
EDITING STITCH PATTERNS Changing the Pattern Size After selecting a stitch pattern, press desired size is selected. Creating a Vertical Mirror Image until the After selecting a stitch pattern, press pattern vertically. to flip the Memo • Stitch patterns entered after the pattern size was changed are added at the selected size until it is changed again. • You cannot change the size of stitch patterns once they have been combined.
EDITING STITCH PATTERNS Selecting a Single/Repeating Pattern Press to select whether the pattern is sewn repeatedly or once. Changing the Thread Density (Satin Stitch Patterns Only) After selecting a stitch pattern, press desired stitching density is selected. Memo If you press until the CAUTION while sewing, the key changes to and the machine will sew one copy of the pattern, then automatically stop. • If the stitches bunch when thread density is changed to , return the thread density to .
EDITING STITCH PATTERNS Returning to the Beginning of the Pattern When sewing character/decorative stitches, you can return to the beginning of the pattern after trial sewing or when the stitching is sewn incorrectly. Memo This function is not available for the stitches in the category. a Press the “Start/Stop” button to stop the machine, and then press . 4 Character/Decorative Stitches → Sewing returns to the beginning of the selected pattern (“W”) from the point where sewing was stopped.
COMBINING STITCH PATTERNS COMBINING STITCH PATTERNS You can combine many varieties of stitch patterns, such as character stitches, cross stitches, satin stitches, or stitches you design with MY CUSTOM STITCH function (see chapter 7 for information about MY CUSTOM STITCH). You can also combine stitch patterns of different sizes, mirror image stitch patterns, and others. Before Combining Patterns Note • When stitch patterns are combined, the machine is automatically set to sew the pattern once.
COMBINING STITCH PATTERNS d Press . Memo • Press to erase the last pattern entered. Patterns are erased one at a time. • If the entire combined pattern cannot be displayed, press to view an image of the pattern. Press to return to the previous screen. e Press . 4 f Character/Decorative Stitches → The image of the pattern appears. To repeatedly sew the pattern combination, press so that it appears as .
COMBINING STITCH PATTERNS Combining Stitch Patterns of Different Sizes c Press again, and then press appears as so that it . Example: a Press . → The second pattern is displayed in the smaller size. d To repeatedly sew the pattern combination, press b Press . . → The larger size pattern appears. 114 so that it appears as → The combination appears as a repeating pattern.
COMBINING STITCH PATTERNS Combining Stitch Patterns of Different Orientations c Press again, and then press appears as so that it . Example: a Press . → The second pattern is flipped horizontally. press b Press so that it appears as . 4 Character/Decorative Stitches d To repeatedly sew the pattern combination, . → The combination appears as a repeating pattern.
COMBINING STITCH PATTERNS Combining Stitch Patterns of Different Lengths a Press c Press again, and then press times so that it appears as three . . → The second pattern is displayed with a length of 2. d To repeatedly sew the pattern combination, press b Press , and then press it appears as so that it appears as . once so that . → The combination appears as a repeating pattern. → The pattern is displayed with a length of 4.
COMBINING STITCH PATTERNS b Creating Step Patterns (7 mm Satin Stitch Patterns Only) Press , and then press . Stitch patterns that are shifted to create a step-shaped pattern are called step patterns. Step patterns can be created by using shift 7 mm satin stitch patterns. and to Press once to move the stitch pattern to the left by half the width of the stitch pattern. Press once to move the stitch pattern to the right by half the width of the stitch pattern.
COMBINING STITCH PATTERNS ■ Examples of Pattern Combinations 118 → → → → → → → → → → → → → → → → → → → → → → →
USING THE MEMORY FUNCTION USING THE MEMORY FUNCTION Stitch Data Precautions Observe the following precautions when using stitch data other than that created and saved in this machine. ■ Types of Stitch Data That Can Be Used • Only .pmu stitch data files can be used with this machine. Using data other than that created using this machine may cause the machine to malfunction. Saving Stitch Patterns in the Machine’s Memory You can save often-used stitch patterns in the machine’s memory.
USING THE MEMORY FUNCTION b Press * Press b . Select a stitch pattern to be deleted. * Press to return to the previous screen without saving the stitch pattern. to display the next page. * Only the first entry of each stitch pattern is displayed in the memory. Press to view the entire stitch pattern. * Press if you do not want to delete the stitch pattern. a → The “Saving” screen appears. When the pattern is saved, the previous screen appears automatically.
USING THE MEMORY FUNCTION d Press . * If you decide not to delete the stitch pattern, press a . Plug the USB cable connectors into the corresponding USB ports on the computer and on the machine. * The USB cable can be plugged into the USB ports on the computer and machine whether or not they are turned on. a b b → The old stitch pattern is deleted, and the new stitch pattern is automatically saved.
USING THE MEMORY FUNCTION c Press * Press . to return to the previous screen without saving the stitch pattern. Retrieving Stitch Patterns from the Machine’s Memory a Press . → The stitch pattern is temporarily saved to “Removable Disk” under “My Computer”. Select the stitch pattern’s .pmu file in d “Removable Disk”, and copy the file to the computer. → The pocket selection screen appears. b Select a stitch pattern to be retrieved. * Press * Press * Press to display the next page.
USING THE MEMORY FUNCTION c Press * Press c . Move/copy the pattern data to “Removable Disk”. to delete the stitch pattern. Memo A maximum of 24 stitch patterns or 476 KB can be moved or copied to “Removable Disk”. → The selected stitch pattern is retrieved and the sewing screen appears. → Stitch pattern data in “Removable Disk” is written to the machine. 4 a Plug the USB cable connectors into the corresponding USB ports on the computer and on the machine (see page 121).
USING THE MEMORY FUNCTION e Select a stitch pattern to be retrieved. * Press to view the entire stitch pattern. * Press to return to the previous screen without retrieving the stitch pattern. a CAUTION • When disconnecting the USB cable: Before disconnecting the USB cable, click the “Unplug or Eject Hardware” icon in the taskbar of Windows Me/2000 or the “Safely Remove Hardware” icon in the taskbar of Windows XP/ Vista/7.
7 Chapter 5 MY CUSTOM STITCH DESIGNING A STITCH......................................................................126 ■ Examples of Custom Stitches .........................................................................................127 ENTERING STITCH DATA .................................................................128 ■ Key Functions ................................................................................................................128 ■ Moving a Point ........................
DESIGNING A STITCH DESIGNING A STITCH By using the MY CUSTOM STITCH™ function, you can register stitches you have created yourself. b Decide the spacing of the stitch. c Place points where the pattern intersects with the grid, and connect all the points with a line. d Determine the x and y coordinates of each of the marked points. * By adjusting the spacing of a stitch, you can create various patterns with one stitch.
DESIGNING A STITCH ■ Examples of Custom Stitches Stitch Stitch Stitch Stitch Stitch Stitch 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 12 18 22 23 21 17 14 12 9 6 3 1 3 6 0 0 3 6 10 13 14 13 11 13 14 13 10 6 3 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 12 41 43 40 41 38 35 32 30 32 35 41 45 47 44 0 0 4 7 11 13 14 13 10 6 3 0 0 4 7 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 45 47 50 54 56 55 51
ENTERING STITCH DATA ENTERING STITCH DATA ■ Key Functions d c b a f e h g k i j m l No. a This area displays the stitch being created. b Displays the number of the present set point over the total number of points in the stitch. c Displays the y-coordinate of Display over the x-coordinate of . Key Name Explanation Page d Grid direction key e Single/triple stitching key Press this key to select whether one or three stitches will be sewn between two points.
ENTERING STITCH DATA a Press b Press . d Press e Select whether one stitch or three stitches will be sewn between the first two points. to add the point indicated by . . * To sew three stitches, press the key so that it appears as c Use to move of the first point on the grid sheet. → Press sheet. . to the coordinates f Use to move to the second point to change the direction of the grid and press .
ENTERING STITCH DATA h Press . ■ Moving a Point a Press or to move that you want to move. * To move to the first point, press . * To move to the last point, press . * You can also move by using the touch pen. Memo • If you have entered points that are too close together, the fabric may not feed properly. Edit the stitch data to leave a larger space between points.
ENTERING STITCH DATA ■ Moving Part or All of the Design a Press or to move Press d Press or to move the section. to the first point of the section that you want to move. * To move to the first point, press . * To move to the last point, press . * You can also move b c Press by using the touch pen. . . 5 MY CUSTOM STITCH → The section will be moved. → The selected point and all points that were entered after it are selected.
ENTERING STITCH DATA ■ Inserting New Points a Press or to move to a place on the design where you want to add a new point. * To move to the first point, press . * To move to the last point, press . * You can also move b Press by using the touch pen. . → A new point is entered and 132 moves to it. c Use to move the point.
USING STORED CUSTOM STITCHES USING STORED CUSTOM STITCHES Saving Custom Stitches in the Machine’s Memory b Press . * Press to return to the previous screen without saving the custom stitch. Stitch patterns created using the MY CUSTOM STITCH™ function can be saved for later use. The machine’s memory can hold up to 15 custom stitches. Note Do not turn off the machine while the “Saving” screen is displayed, otherwise you may lose the custom stitches that you are saving.
USING STORED CUSTOM STITCHES b d Select a custom stitch to be deleted. * Press to view the entire custom stitch. Press . * If you decide not to delete the custom stitch, press . * Press if you do not want to delete the custom stitch. a → The old custom stitch is deleted, and the new custom stitch is automatically saved. a Saved custom stitches c Press .
USING STORED CUSTOM STITCHES Retrieving Custom Stitches from the Machine’s Memory a Press c Press * Press . to delete the custom stitch. . → The selected custom stitch is retrieved and the sewing screen appears. → The pocket selection screen appears. b Retrieving Custom Stitches from the Computer Select a custom stitch to be retrieved. * Press * Press to view the entire custom stitch. to return to the previous screen without saving the custom stitch.
USING STORED CUSTOM STITCHES 136
9 Chapter 6 Appendix CARE AND MAINTENANCE ..............................................................138 Cleaning the LCD ..................................................................................................138 Cleaning the Machine Casing ................................................................................138 Cleaning the Race .................................................................................................138 Cleaning the Bobbin Case .........................
CARE AND MAINTENANCE CARE AND MAINTENANCE CAUTION • Be sure to unplug the machine before cleaning it. Otherwise, electric shock or injury may result. g Cleaning the LCD Grasp the bobbin case, and then pull it out. If the surface of the LCD is dirty, lightly wipe it with a soft dry cloth. Do not use organic solvents or detergents. Cleaning the Machine Casing If the surface of the machine is dirty, dampen a cloth with a neutral detergent, wring it out firmly, and then wipe the surface.
CARE AND MAINTENANCE i Insert the bobbin case so that the ▲ mark aligns with the ● mark as shown below. Thread wax and dust easily collect around the notch in the tension spring on the bobbin case, resulting in an incorrect thread tension. Therefore, the bobbin case should be cleaned as necessary should tension problems arise.
ADJUSTING THE SCREEN ADJUSTING THE SCREEN Screen Visibility Is Low If the screen is difficult to read when the machine is turned on, follow the procedure described below. a Turn off the machine, hold your finger anywhere on the screen, and then turn the machine on. Touch Panel Is Malfunctioning If the screen does not respond correctly when a key is pressed (the machine does not perform the operation or performs a different operation), follow the procedure described below to make the proper adjustments.
ADJUSTING THE SCREEN c Using the included touch pen, lightly touch the center of each ×, in order from 1 to 5. * If the buzzer sounds one time after you press number 5, the operation is finished, and “SUCCESS” appears on the screen. If the buzzer sounds twice, there was an error. In this case, repeat the steps above. Note Only use the included touch pen to touch the screen. Do not use a mechanical pencil, screwdriver or any other hard or sharp object.
TROUBLESHOOTING TROUBLESHOOTING If you have a minor problem with your sewing machine, check the following solutions. If the solutions suggested do not correct the problem, contact your authorized dealer. Memo This machine is equipped with a simple troubleshooting feature that can be used in case minor problems occur during sewing. Press , and then press to display a list of problems. Press the key for the appropriate problem, and then check for the causes that are displayed.
TROUBLESHOOTING Problem High-pitched sound while sewing Cannot thread the needle Cause Remove the dust or lint. 138 Pieces of thread are caught in the race (bobbin case). Clean the race (bobbin case). 138 The upper threading is incorrect. Check the procedure for threading the machine and rethread it correctly. 27 There are scratches on the race (bobbin case). Replace the race (bobbin case), or consult your authorized dealer. − The needle is not in the correct position.
TROUBLESHOOTING CAUTION • This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the upper threading is done, the machine will not operate properly. Also, depending on the pattern selected, the machine may feed the fabric even if the needle is raised. This is due to the needle bar release mechanism. At these times, the machine will make a sound different from that made during normal sewing. This is not the sign of a malfunction.
ERROR MESSAGES ERROR MESSAGES If the “Start/Stop button” or the “Reverse/Reinforcement Stitch” button is pressed before the machine is correctly set up or if an incorrect operation is performed, the machine stops and informs you of the error with an alarm and an error message. If an error message appears, correct the problem according to the instructions in the message. (The message that is displayed can be cancelled either by pressing or performing the operation correctly.
ERROR MESSAGES This message is displayed when This message is displayed when the bobbin thread is running out. is pressed while the presser foot is raised. This message is displayed when or This message is displayed when the bobbin is being wound, and the motor locks because the thread is tangled, etc. is pressed after a pattern is selected. This message is displayed when is pressed while a utility This message is displayed when the needle is in the down position and the needle threader is lowered.
ERROR MESSAGES This message is displayed when the machine is set for twin needle sewing and a pattern that cannot be sewn with the twin needle is selected. This message is displayed when you try to sew with a stitch other than a middle needle position stitch while the single-hole needle plate is installed. This message is displayed when the needle plate is removed with the machine on.
SPECIFICATIONS SPECIFICATIONS Item Sewing Machine 148 Specification Dimensions 51.1 cm (W) × 30.5 cm (H) × 25.8 cm (D) (approx. 20-1/8 inches (W) × 12 inches (H) × 10-1/8 inches (D)) Case dimensions 58.2 cm (W) × 31.9 cm (H) × 28.4 cm (D) (approx. 22-7/8 inches (W) × 12-1/2 inches (H) × 11-1/8 inches (D)) Weight 11.3 kg (24.9 lb.
UPGRADING YOUR MACHINE’S SOFTWARE UPGRADING YOUR MACHINE’S SOFTWARE You can use a computer to download software upgrades for your sewing machine. When an upgrade program is available on “http://solutions.brother.com”, please download the files following the instructions on the web site and steps below. Note There are two upgrade files. Be sure to download both files successively. Memo • When the machine’s software is upgraded, saved combinations of character and decorative stitches are erased.
UPGRADING YOUR MACHINE’S SOFTWARE h When the following screen appears, upgrading is completed. Press LOAD after saving the upgrade file in the machine. Upgrade complete. Note If an error occurred, an error message appears. At this time, turn the machine off, and then start the procedure again from step a. i 150 Disconnect the USB cable, and turn the machine off, then on again.
STITCH SETTING CHART STITCH SETTING CHART Note When using the twin needle (see page 30), be sure to attach presser foot “J”. Stitch Key Stitch Name Presser Foot Stitch Width [mm (inch)] Applications Stitch Length [mm (inch)] Twin Needle Auto Manual Auto Manual General sewing, gather, pintuck, etc. Reverse stitch is sewn while pressing “Reverse/ Reinforcement Stitch” button. 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK (J) General sewing, gather, pintuck, etc.
STITCH SETTING CHART Stitch Key Stitch Name Stitch Length [mm (inch)] Twin Needle Auto Manual Auto Manual 5.0 (3/16) 1.5 - 7.0 (1/16 - 1/4) 1.0 (1/16) 0.2 - 4.0 (1/64 - 1/16) OK (J) 3.5 (1/8) 2.5 - 5.0 (3/32 - 3/16) 2.0 (1/16) 1.0 - 4.0 (1/16 - 3/16) NO 5.0 (3/16) 2.5 - 5.0 (3/32 - 3/16) 2.5 (3/32) 1.0 - 4.0 (1/16 - 3/16) NO Reinforcing of medium, 5.0 heavyweight and easily frayed (3/16) fabrics or decorative stitching 3.5 - 5.0 (1/8 - 3/16) 2.5 (3/32) 1.0 - 4.
STITCH SETTING CHART Stitch Key Stitch Name Piecing stitch (Right) Piecing stitch (Middle) Piecing stitch (Left) Hand-look quilting Presser Foot Twin Needle Auto Manual Auto Manual 0.0 - 7.0 (0 - 1/4) 2.0 (1/16) 0.2 - 5.0 (1/64 - 3/16) NO — — 2.0 (1/16) 0.2 - 5.0 (1/64 - 3/16) NO 1.5 (1/16) 0.0 - 7.0 (0 - 1/4) 2.0 (1/16) 0.2 - 5.0 (1/64 - 3/16) NO 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 1.0 - 4.0 (1/16 - 3/16) NO 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 1.4 (1/16) 0.0 - 4.
STITCH SETTING CHART Stitch Key Stitch Name Ladder stitch Applications Decorative stitching Rick-rack stitch Decorative top stitching Decorative stitch Decorative stitching Serpentine stitch Decorative stitching and attaching elastic Decorative stitch Decorative stitching and appliqué Decorative stippling stitch Decorative stitching Hemstitching Decorative hems, triple straight at left Hemstitching Hemstitching zigzag Hemstitching Hemstitching Hemstitching Hemstitching Hemstitching
STITCH SETTING CHART Stitch Key Stitch Name Honeycomb stitch Honeycomb stitch Hemstitching Hemstitching Hemstitching Hemstitching Hemstitching Hemstitching Hemstitching Hemstitching Hemstitching Presser Foot Applications Heirloom, decorative hems Heirloom, decorative hems Heirloom, decorative hems Heirloom, decorative hems Heirloom, decorative hems Heirloom, decorative hems Heirloom, decorative hems Decorative hems and bridging stitch Decorative hems.
STITCH SETTING CHART Stitch Key Stitch Name Stitch Width [mm (inch)] Applications Stitch Length [mm (inch)] Twin Needle Auto Manual Auto Manual 5.0 (3/16) 0.0 - 6.0 (0 - 15/64) 2.0 (1/16) 0.2 - 4.0 (1/64 - 3/16) NO Buttonholes in heavyweight or thick fabrics for larger flat buttons 7.0 (1/4) 3.0 - 7.0 (1/8 - 1/4) 0.5 (1/32) 0.3 - 1.0 (1/64 - 1/16) NO Tapered keyhole buttonhole Buttonholes in medium to heavy weight fabrics for larger flat buttons 7.0 (1/4) 3.0 - 7.0 (1/8 - 1/4) 0.
STITCH SETTING CHART Stitch Key Stitch Name Presser Foot Forward (Zigzag) Reverse (Zigzag) Stitch Key Stitch Name Piecing stitch (Middle) Piecing stitch (Right) Piecing stitch (Left) Manual Auto Manual — — — — NO For attaching appliqué on tubular pieces of fabric and mitering corners — — — — NO Presser Foot Auto Manual — — 2.0 (1/16) 0.2 - 5.0 (1/64 - 3/16) NO Piecework/patchwork 5.5 6.5 mm (approx. 1/4 inch) right (7/32) seam allowance 0.0 - 7.0 (0 - 1/4) 2.0 (1/16) 0.
STITCH SETTING CHART Stitch Key Stitch Name Applications Stitch Width [mm (inch)] Stitch Length [mm (inch)] Twin Needle Auto Manual Auto Manual 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 4.0 (3/16) 1.0 - 4.0 (1/16 - 3/16) NO 5.5 (7/32) 0.0 - 7.0 (0 - 1/4) 1.4 (1/16) 0.2 - 4.0 (1/61 - 3/16) NO 5.0 (3/16) 1.5 - 7.0 (1/16 - 1/4) 2.0 (1/16) 0.2 - 4.0 (1/64 - 3/16) NO 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 1.0 - 4.0 (1/16 - 3/16) NO 5.0 (3/16) 2.5 - 7.0 (3/32 - 1/4) 2.5 (3/32) 1.0 - 4.
INDEX INDEX Numerics 1/4" quilting foot with guide ..........................................................71 A accessories ....................................................................................11 air vent ...........................................................................................9 alarm ..........................................................................................147 alphabet patterns character/decorative stitches ...............................................
INDEX MY CUSTOM STITCH designing ................................................................................ 126 entering data ........................................................................... 128 key functions .......................................................................... 128 N needle changing the position ............................................................... 56 fabric/thread/needle combinations ............................................ 35 replacing ................
