Command Reference Guide for Software Developers
Table Of Contents
- Technical Reference Guide
- TABLE OF CONTENTS
- GLOSSARY
- CHAPTER 1 INTRODUCTION
- CHAPTER 2 PCL PRINTER CONTROL LANGUAGE
- 1. COMMAND LIST
- 2. INTRODUCTION
- 3. CONTROLLING THE PRINTER
- 4. JOB CONTROL
- 4.1 . Commands
- 4.1.1. Page size
- 4.1.2. Media type selection
- 4.1.3. Output tray
- 4.1.4. Paper source
- 4.1.5. Left long-edge offset registration
- 4.1.6. Top offset registration
- 4.1.7. Simplex/duplex printing
- 4.1.8. Paper side selection
- 4.1.9. Job separation command
- 4.1.10. Reset
- 4.1.11. Reset to factory default settings
- 4.1.12. Reset to user settings
- 4.1.13. Printer self test
- 4.1.14. Exit current emulation mode
- 4.1.15. Change emulation mode
- 4.2. The Page
- 4.2.1. Physical page
- 4.2.2. Printable area
- 4.2.3. Logical page
- 4.2.4. Text area
- 4.2.5. HP-GL/2 graphics window
- 4.2.6. Portrait page dimensions
- 4.2.7. Landscape page dimensions
- 4.2.8. Coordinates
- 4.2.9. Units
- 4.2.10. Unit of measure
- 4.2.11. Setting the left and right margins
- 4.2.12. Resetting the horizontal margins
- 4.2.13. Setting the top margin
- 4.2.14. Setting the vertical motion index (VMI)
- 4.2.15. Setting the horizontal motion index (HMI)
- 4.2.16. Setting line spacing
- 4.2.17. Text length
- 4.2.18. Page length
- 4.2.19. Perforation skip
- 4.2.20. Positioning the cursor
- 4.2.21. Vertical positioning
- 4.2.22. Horizontal position
- 4.2.23. Positioning the cursor using control codes
- 4.2.24. Using the cursor position stack
- 4.2.25. Half line feed
- 4.2.26. Logical page orientation
- 4.2.27. Text direction
- 4.1 . Commands
- 5. USING FONTS
- 5.1. Introduction
- 5.1.1. Font types
- 5.1.2. Bitmap fonts
- 5.1.3. Scalable fonts
- 5.1.4. Bound fonts
- 5.1.5. Unbound fonts
- 5.1.6. Font sources
- 5.1.7. Internal fonts
- 5.1.8. Card/cartridge fonts
- 5.1.9. Downloadable fonts
- 5.1.10. Primary and secondary fonts
- 5.1.11. Specifying the primary font
- 5.1.12. Specifying the secondary font
- 5.1.13. Selecting the default fonts
- 5.1.14. Switching between the primary and secondary fonts
- 5.1.15. Criteria for font selection
- 5.1.16. Symbol set
- 5.1.17. Symbol collections
- 5.1.18. Type of character spacing
- 5.1.19. Pitch
- 5.1.20. Height
- 5.1.21. Style
- 5.1.22. Stroke weight
- 5.1.23. Typeface
- 5.2. Font Selection Commands
- 5.2.1. User-defined symbol sets
- 5.2.2. Symbol set ID code command
- 5.2.3. Define symbol set
- 5.2.4. Symbol set control command
- 5.2.5. Selecting the symbol set
- 5.2.6. Selecting the type of character spacing
- 5.2.7. Selecting the pitch
- 5.2.8. Selecting the height
- 5.2.9. Scaling the scalable fonts vertically or horizontally
- 5.2.10. Selecting the style
- 5.2.11. Selecting the stroke weight
- 5.2.12. Selecting the typeface
- 5.2.13. Font orientation
- 5.2.14. Transparent print data
- 5.2.15. Esc&d#D (27)(38)(100)#(68) <1Bh><26h><64h>#<44h>
- 5.3. Downloadable font manipulation
- 5.4. Creating Downloadable Fonts
- 5.1. Introduction
- 6. USING GRAPHICS
- 6.1. Source, Pattern and Destination
- 6.2. Plotting Rectangles
- 6.3. Raster Graphics
- 6.3.1. Positioning the cursor
- 6.3.2. Set raster resolution
- 6.3.3. Set high resolution control
- 6.3.4. Set raster image orientation
- 6.3.5. Set raster area height
- 6.3.6. Set raster area width
- 6.3.7. Set raster y-offset
- 6.3.8. Set compression mode
- 6.3.9. Start raster transfer
- 6.3.10. Send raster data
- 6.3.11. Compress transfer graphics
- 6.3.12. End raster transfer
- 6.3.13. Horizontal 1200-dpi image format mode (Raster Graphic Mode 1027)
- 6.4. Vector Graphics
- 6.5. The Picture Frame
- 7. MACROS
- 7.1. The Purpose of a Macro
- 7.2. Defining a Macro
- 7.3. Running a Macro
- 7.4. Handling Macros
- 7.4.1. Delete all macros
- 7.4.2. Delete all temporary macros
- 7.4.3. Delete macro
- 7.4.4. Make macro temporary
- 7.4.5. Make macro permanent
- 7.4.6. Delete all macros from the storage device
- 7.4.7. Delete macro from the storage device
- 7.4.8. Save macro into the storage device
- 7.4.9. Execute data
- 7.4.10. AppleTalk configuration
- 7.4.11. MIO video I/O port control
- 8. STATUS READBACK
- 8.1. Introduction
- 8.2. Memory Status request
- 8.3. Entity Status
- 8.4. Status Response
- 8.5. Status Response Syntax
- 8.5.1. Set status readback location type
- 8.5.2. Set status readback location unit
- 8.5.3. Inquire status readback entity
- 8.5.4. Entity status response
- 8.5.5. Font response
- 8.5.6. Bitmap fonts
- 8.5.7. Bound scalable fonts
- 8.5.8. Unbound scalable fonts
- 8.5.9. Download fonts
- 8.5.10. Location type 1 (currently selected) font
- 8.5.11. Font extended response
- 8.5.12. Macro response
- 8.5.13. Use-defined pattern response
- 8.5.14. Symbol set response
- 8.5.15. Entity error codes
- 8.5.16. Free space command
- 8.5.17. Font cache
- 8.5.18. Memory status response
- 8.5.19. Memory error response
- 8.5.20. Flush all pages command
- 8.5.21. Echo command
- 9. INDEX
- CHAPTER 3 PCL5C
- CHAPTER 4 HP-GL/2 GRAPHICS LANGUAGE
- CHAPTER 5 PJL PRINTER JOB LANGUAGE
- 1. INTRODUCTION
- 2. HOW TO USE PJL
- 3. COMMAND GROUP
- 4. KERNEL COMMANDS
- 5. JOB SEPARATION COMMANDS
- 6. ENVIRONMENT COMMANDS
- 7. STATUS READBACK COMMANDS
- 8. DEVICE ATTENDANCE COMMANDS
- 9. INDEX
- CHAPTER 6 EPSON FX-850
- CHAPTER 7 IBM PROPRINTER XL
- CHAPTER 8 BAR CODE CONTROL
- 1. INTRODUCTION
- 2. PRINT BAR CODES OR EXPANDED CHARACTERS
- 3. DEFINITION OF PARAMETERS
- 3.1. Bar Code Mode
- 3.2. Bar Code Style, Expanded Character Shading, Line Block Drawing & Box Drawing Shading
- 3.3. Bar Code Scaling (Width only)
- 3.4. Bar Code Human Readable Line On or Off
- 3.5. Quiet Zone
- 3.6. Bar Code, Expanded Character Unit, Line Block Drawing & Box Drawing Units
- 3.7. Bar Code, Expanded Character, Line, Block Drawing & Box Drawing Offset in the X-axis
- 3.8. Bar Code & Expanded Character Offset in the Y-axis
- 3.9. Bar Code, Expanded Character, Line, Block Drawing & Box Drawing Height
- 3.10. Expanded Character, Line Block Drawing & Box Drawing Width
- 3.11. Expanded Character Rotation
- 3.12. Bar Code Data Start
- 3.13. Box Drawing
- 3.14. Line Block Drawing
- 3.15. Expanded Character Data Start
- 3.16. Table of Code(EAN) 128 set C
- 4. EXAMPLE PROGRAM LISTINGS
- CHAPTER 9 HP-GL GRAPHICS LANGUAGE
- CHAPTER 10 CARBON COPY FUNCTION
- APPENDIX A COMPARISON LIST
- APPENDIX B FLASH/PCMCIA CARD COMMANDS
- APPENDIX C HBP MODE COMMANDS
- APPENDIX D REFERENCE LIST OF MX-2000/4000/5000/7000 SERIES UNIQUE COMMANDS
- APPENDIX E REFERENCE LIST OF FS-5050 UNIQUE COMMANDS
- APPENDIX F REFERENCE LIST OF SF- 4000 SERIES UNIQUE COMMANDS
CHAPTER 2 PCL - 51
5.1.15. Criteria for font selection
The printer will try to match your stated font requirements as best it can with the fonts available to it in any of
the three possible font locations. In most cases you will be specifying a font you know to be present in one of
the locations and the resulting printed text will appear exactly as you envisaged. However, if you specify a
particular combination of font characteristics that is not possible, the printer will produce the closest possible
match that it can by satisfying the following specifications in the following order: symbol set / spacing type /
pitch (for monospaced fonts) / height / stroke weight / style.
The meanings of each of these are explained in the following sub-sections. Likewise, if you simply specify a
font attribute that is not available, for example if you request a Utah Light font when only Utah Medium and
Utah Bold are available in the font locations, the printer will simply ignore the requirement (light stroke weight,
in this case) that it cannot fulfill.
5.1.16. Symbol set
The symbol set is the list of symbols that constitute a particular font. Normally, symbol sets contain lower and
upper case letters, numbers, punctuation marks and a selection of other commonly used symbols. Some symbol
sets are designed for specific needs, for example, for generating text with mathematical expressions. The symbol
set has the highest priority of all the characteristics you specify when you designate the font you require. If the
symbol set you choose is available, but not in conjunction with any of the other characteristics you specify, the
printer will satisfy your symbol set request at the expense of the rest of your designation and the text printed out
may well look completely different from what you expected to see.
5.1.17. Symbol collections
The symbol collections contain many symbols and a symbol set is made from symbol collections by selecting
the required symbols for unbound fonts. As symbol collections have more symbols than symbol sets, unbound
fonts can have more symbols than bound fonts. Due to the compatibility between symbol sets and symbol
collections, the printer searches the designated MSL or Unicode number by using a symbol set mapping table.
5.1.18. Type of character spacing
Character spacing is either fixed (monospacing), in which every printed character is allocated the same amount
of space on the line, or proportional, where characters are spaced according to their shape and size. For any
serious typographic work proportional spacing is essential since fixed spacing is unattractive and hard to read.
In general, monospacing is used with bitmap fonts and proportional spacing is used with scalable fonts.
However, proportionally spaced bitmap fonts do exist.
5.1.19. Pitch
Pitch is the number of characters that are printed per inch and therefore only applies to monospaced fonts. If you
make a pitch selection while using a proportionally spaced font the command will have no immediate effect.
However, the new pitch will be stored as part of the primary (or secondary) font designation and applied the
next time a monospaced font is selected as the primary (or secondary) font.
The printer's in-built bitmap fonts all have a pitch of either 10, 12 or 16.66 characters per inch.
5.1.20. Height
Height refers to the height in points (1/72") of unaccented capital letters in a font. This is the generally accepted
method of defining the height of a font's characters. Scaled fonts can be specified to an accuracy of 0.25 points.
5.1.21. Style
A font's style is defined by its posture (upright or italic), width (condensed, normal or expanded) and structure
(solid, outline or shadow). Upright and italic bitmap fonts and scalable typefaces are available in the printer's
ROM. However, these are all normal and solid fonts. To print using any of the other styles (for example, using
Condensed Helsinki or Outline Tennessee) you would have to download the requisite font or install a font
card/cartridge containing it.