User's Guide
Table Of Contents
- SOMMARIO
- CAPITOLO 1 INTRODUZIONE
- INFORMAZIONI SU QUESTA GUIDA DELL'UTENTE
- INFORMAZIONI GENERALI SULLA STAMPANTE
- VERIFICA DEI COMPONENTI INCLUSI NELLA CONFEZIONE
- VISTA GENERALE
- FUNZIONALITÀ
- Risoluzione di classe 2400 DPI
- Alta velocità e stampa laser a colori
- Color Advanced PhotoScale Technology (APT)
- HRC (High Resolution Control)
- Cartuccia di toner economica a manutenzione zero
- Vassoio carta universale
- Tre interfacce
- Selezione automatica dell'interfaccia
- Cinque modi di emulazione
- Selezione automatica dell'emulazione
- Tecnologia di compressione dei dati
- Font
- Funzione di blocco del pannello
- Modo risparmio energia
- Modo risparmio toner
- Funzione di ristampa
- Calibrazione PANTONE ®
- Rete
- ACCESSORI OPZIONALI
- RAM
- AMBIENTE OPERATIVO E DI MAGAZZINO
- CAPITOLO 2 DRIVER E SOFTWARE
- DRIVER DELLA STAMPANTE
- IMPOSTAZIONI DELLA STAMPANTE
- CAPITOLO 3 PRIMA DI UTILIZZARE LA STAMPANTE
- CAPITOLO 4 FUNZIONAMENTO DEL PANNELLO DI CONTROLLO
- PANNELLO DI CONTROLLO
- TASTI
- LED
- DISPLAY LCD
- UTILIZZO DEL PANNELLO DI CONTROLLO
- MENU INSTALLAZIONE DEL PANNELLO
- CAPITOLO 5 MANUTENZIONE
- SOSTITUZIONE DEI MATERIALI DI CONSUMO
- PULIZIA DELLA STAMPANTE
- REIMBALLAGGIO E RIPOSIZIONAMENTO DELLA STAMPANTE
- OPZIONI
- CAPITOLO 6 RISOLUZIONE DEI PROBLEMI
- APPENDICE
- INDICE
NORMATIVE
xiv
Wiring Information (solo per il Regno Unito)
Important
If the mains plug supplied with this printer is not suitable for your socket outlet, remove the plug from the
mains cord and fit an appropriate three pin plug. If the replacement plug is intended to take a fuse then fit the
same rating fuse as the original.
If a moulded plug is severed from the mains cord then it should be destroyed because a plug with cut wires is
dangerous if engaged in a live socket outlet. Do not leave it where a child might find it!
In the event of replacing the plug fuse, fit a fuse approved by ASTA to BS1362 with the same rating as the
original fuse.
Always replace the fuse cover. Never use a plug with the cover omitted.
WARNING - THIS PRINTER MUST BE PROPERLY EARTHED.
The wires in the mains cord are colored in accordance with the following code:
Green and yellow: Earth
Blue: Neutral
Brown: Live
The colours of the wires in the main lead of this printer may not correspond with the colored markings
identifying the terminals in your plug.
If you need to fit a different plug, proceed as follows.
Remove a length of the cord outer sheath, taking care not to damage the colored insulation of the wires inside.
Cut each of the three wires to the appropriate length. If the construction of the plug permits, leave the green and
yellow wire longer than the others so that, in the event that the cord is pulled out of the plug, the green and
yellow wire will be the last to disconnect.
Remove a short section of the colored insulation to expose the wires.
The wire which is colored green and yellow must be connected to the terminal in the plug which is marked with
the letter "E" or by the safety earth symbol
or colored green or green and yellow.
The wire which is colored blue must be connected to the terminal which is marked with the letter "N" or
colored black or blue.
The wire which is colored brown must be connected to the terminal which is marked with the letter "L" or
colored red or brown.
The outer sheath of the cord must be secured inside the plug. The colored wires should not hang out of the
plug.