User Manual
Table Of Contents
- USER'S GUIDE HL-5340D / HL-5350DN / HL-5370DW
- Using this guide
- Safety precautions
- Trademarks
- Compilation and Publication Notice
- Shipment of the Printer
- Table of Contents
- 1 About this Printer
- 2 Printing Methods
- 3 Driver and Software
- Printer driver
- Features in the printer driver (for Windows®)
- Basic tab
- Paper Size
- Orientation
- Copies
- Media Type
- Resolution
- Print Setting
- Multiple Page
- Duplex / Booklet
- Paper Source
- Advanced tab
- Scaling
- Reverse Print
- Use Watermark
- Header-Footer Print
- Toner Save Mode
- Administrator
- Other Print Options...
- Use Reprint
- Sleep Time
- Macro
- Page Protection
- Density Adjustment
- Error Message Printout
- Improve Print Output
- Accessories tab
- Support
- Status Monitor
- Using the BR-Script3 printer driver (PostScript® 3™ language emulation for Windows®)
- Features in the printer driver (for Macintosh)
- Features in the printer driver (for Windows®)
- Using the BR-Script3 printer driver (Post Script® 3™ language emulation for Macintosh)
- Uninstalling the printer driver
- Software
- Printer driver
- 4 Control Panel
- 5 Options
- 6 Routine Maintenance
- 7 Troubleshooting
- Appendix A
- Printer specifications
- Symbol and character sets
- Quick reference for bar code control commands
- Print bar codes or expanded characters
- Definition of parameters
- Bar code mode
- Bar code, expanded character, line block drawing and box drawing
- Bar code
- Bar code human readable line ON or OFF
- Quiet zone
- Bar code, expanded character unit, line block drawing and box drawing
- Bar code, expanded character, line block drawing and box drawing offset in X-axis
- Bar code & expanded character offset in Y-axis
- Bar code, expanded character, line block drawing and box drawing height
- Expanded character width, line block drawing and box drawing
- Expanded character rotation
- Bar code data start
- Box drawing
- Line block drawing
- Expanded character data start
- Print bar codes or expanded characters
- Appendix B (for Europe and Other Countries)
- Appendix C (for USA and Canada)
- Index
Appendix
154
A
This parameter shows the height of bar codes or expanded characters as shown above. It can start with ‘h’,
‘H’, ‘d’, or ‘D’. The height of bar codes is shown in the ‘u’- or ‘U’-specified unit. The default setting of the bar
code height (12 mm, 18 mm or 22 mm) is determined by the bar code mode selected by ‘t’ or ‘T’.
Expanded character width, line block drawing and box drawing 0
n = ‘wnnn’ or ‘Wnnn’
Expanded character i 1.2 mm
Line block drawing and box drawing i 1 dot
This parameter shows the width of expanded characters as shown above.
Expanded character rotation 0
Bar code data start 0
n = ‘b’ or ‘B’
Data that follows ‘b’ or ‘B’ is read in as bar code data. Bar code data must end with the ‘ \ ’ code (5CH), which
also ends this command. The acceptable bar code data is determined by the bar code mode selected by ‘t’
or ‘T’.
When CODE 39 is chosen with the parameter ‘t0’ or ‘T0’
Forty three characters ‘0’ to ‘9’, ‘A’ to ‘Z’, ‘-’, ‘ . ’, ‘ (space)’, ‘$’, ‘ / ’, ‘+’, and ‘%’ can be accepted as bar code
data. Other characters will cause a data error. The number of characters for bar codes is not limited. The
bar code data automatically starts and ends with an asterisk ‘ * ’ (start character and stop character). If the
received data has an asterisk ‘ * ’ at the beginning or end, the asterisk is regarded as a start character or
stop character.
When Interleaved 2 of 5 is selected with the parameter ‘t1’ or ‘T1’:
Ten numerical characters ‘0’ to ‘9’ can be accepted as bar code data. Other characters cause a data error.
The number of characters for bar codes is not limited. This mode of bar codes needs even characters. If
the bar code data has odd characters, ‘0’ is automatically added to the end of the bar code data.
When FIM (US-Post Net) is selected with the parameter ‘t3’ or ‘T3’
Characters ‘A’ to ‘D’ are valid and one digit of data can be printed. Upper-case and lower-case alphabet
characters can be accepted.
When Post Net (US-Post Net) is selected with the parameter ‘t4’ or ‘T4’
Numbers ‘0’ to ‘9' can be data and it must end with a check digit. ‘?’ can be used instead of the check digit.
n = ‘a0’ or ‘A0’ ‘Upright (preset)
n = ‘a1’ or ‘A1’ ‘Rotated 90 degrees
n = ‘a2’ or ‘A2’ ‘Upside down, rotated 180 degrees
n = ‘a3’ or ‘A3’ ‘Rotated 270 degrees