Command Reference Guide for Software Developers
Table Of Contents
- Technical Reference Guide
- TABLE OF CONTENTS
- GLOSSARY
- CHAPTER 1 INTRODUCTION
- CHAPTER 2 PCL PRINTER CONTROL LANGUAGE
- 1. COMMAND LIST
- 2. INTRODUCTION
- 3. CONTROLLING THE PRINTER
- 4. JOB CONTROL
- 4.1 . Commands
- 4.1.1. Page size
- 4.1.2. Media type selection
- 4.1.3. Output tray
- 4.1.4. Paper source
- 4.1.5. Left long-edge offset registration
- 4.1.6. Top offset registration
- 4.1.7. Simplex/duplex printing
- 4.1.8. Paper side selection
- 4.1.9. Job separation command
- 4.1.10. Reset
- 4.1.11. Reset to factory default settings
- 4.1.12. Reset to user settings
- 4.1.13. Printer self test
- 4.1.14. Exit current emulation mode
- 4.1.15. Change emulation mode
- 4.2. The Page
- 4.2.1. Physical page
- 4.2.2. Printable area
- 4.2.3. Logical page
- 4.2.4. Text area
- 4.2.5. HP-GL/2 graphics window
- 4.2.6. Portrait page dimensions
- 4.2.7. Landscape page dimensions
- 4.2.8. Coordinates
- 4.2.9. Units
- 4.2.10. Unit of measure
- 4.2.11. Setting the left and right margins
- 4.2.12. Resetting the horizontal margins
- 4.2.13. Setting the top margin
- 4.2.14. Setting the vertical motion index (VMI)
- 4.2.15. Setting the horizontal motion index (HMI)
- 4.2.16. Setting line spacing
- 4.2.17. Text length
- 4.2.18. Page length
- 4.2.19. Perforation skip
- 4.2.20. Positioning the cursor
- 4.2.21. Vertical positioning
- 4.2.22. Horizontal position
- 4.2.23. Positioning the cursor using control codes
- 4.2.24. Using the cursor position stack
- 4.2.25. Half line feed
- 4.2.26. Logical page orientation
- 4.2.27. Text direction
- 4.1 . Commands
- 5. USING FONTS
- 5.1. Introduction
- 5.1.1. Font types
- 5.1.2. Bitmap fonts
- 5.1.3. Scalable fonts
- 5.1.4. Bound fonts
- 5.1.5. Unbound fonts
- 5.1.6. Font sources
- 5.1.7. Internal fonts
- 5.1.8. Card/cartridge fonts
- 5.1.9. Downloadable fonts
- 5.1.10. Primary and secondary fonts
- 5.1.11. Specifying the primary font
- 5.1.12. Specifying the secondary font
- 5.1.13. Selecting the default fonts
- 5.1.14. Switching between the primary and secondary fonts
- 5.1.15. Criteria for font selection
- 5.1.16. Symbol set
- 5.1.17. Symbol collections
- 5.1.18. Type of character spacing
- 5.1.19. Pitch
- 5.1.20. Height
- 5.1.21. Style
- 5.1.22. Stroke weight
- 5.1.23. Typeface
- 5.2. Font Selection Commands
- 5.2.1. User-defined symbol sets
- 5.2.2. Symbol set ID code command
- 5.2.3. Define symbol set
- 5.2.4. Symbol set control command
- 5.2.5. Selecting the symbol set
- 5.2.6. Selecting the type of character spacing
- 5.2.7. Selecting the pitch
- 5.2.8. Selecting the height
- 5.2.9. Scaling the scalable fonts vertically or horizontally
- 5.2.10. Selecting the style
- 5.2.11. Selecting the stroke weight
- 5.2.12. Selecting the typeface
- 5.2.13. Font orientation
- 5.2.14. Transparent print data
- 5.2.15. Esc&d#D (27)(38)(100)#(68) <1Bh><26h><64h>#<44h>
- 5.3. Downloadable font manipulation
- 5.4. Creating Downloadable Fonts
- 5.1. Introduction
- 6. USING GRAPHICS
- 6.1. Source, Pattern and Destination
- 6.2. Plotting Rectangles
- 6.3. Raster Graphics
- 6.3.1. Positioning the cursor
- 6.3.2. Set raster resolution
- 6.3.3. Set high resolution control
- 6.3.4. Set raster image orientation
- 6.3.5. Set raster area height
- 6.3.6. Set raster area width
- 6.3.7. Set raster y-offset
- 6.3.8. Set compression mode
- 6.3.9. Start raster transfer
- 6.3.10. Send raster data
- 6.3.11. Compress transfer graphics
- 6.3.12. End raster transfer
- 6.3.13. Horizontal 1200-dpi image format mode (Raster Graphic Mode 1027)
- 6.4. Vector Graphics
- 6.5. The Picture Frame
- 7. MACROS
- 7.1. The Purpose of a Macro
- 7.2. Defining a Macro
- 7.3. Running a Macro
- 7.4. Handling Macros
- 7.4.1. Delete all macros
- 7.4.2. Delete all temporary macros
- 7.4.3. Delete macro
- 7.4.4. Make macro temporary
- 7.4.5. Make macro permanent
- 7.4.6. Delete all macros from the storage device
- 7.4.7. Delete macro from the storage device
- 7.4.8. Save macro into the storage device
- 7.4.9. Execute data
- 7.4.10. AppleTalk configuration
- 7.4.11. MIO video I/O port control
- 8. STATUS READBACK
- 8.1. Introduction
- 8.2. Memory Status request
- 8.3. Entity Status
- 8.4. Status Response
- 8.5. Status Response Syntax
- 8.5.1. Set status readback location type
- 8.5.2. Set status readback location unit
- 8.5.3. Inquire status readback entity
- 8.5.4. Entity status response
- 8.5.5. Font response
- 8.5.6. Bitmap fonts
- 8.5.7. Bound scalable fonts
- 8.5.8. Unbound scalable fonts
- 8.5.9. Download fonts
- 8.5.10. Location type 1 (currently selected) font
- 8.5.11. Font extended response
- 8.5.12. Macro response
- 8.5.13. Use-defined pattern response
- 8.5.14. Symbol set response
- 8.5.15. Entity error codes
- 8.5.16. Free space command
- 8.5.17. Font cache
- 8.5.18. Memory status response
- 8.5.19. Memory error response
- 8.5.20. Flush all pages command
- 8.5.21. Echo command
- 9. INDEX
- CHAPTER 3 PCL5C
- CHAPTER 4 HP-GL/2 GRAPHICS LANGUAGE
- CHAPTER 5 PJL PRINTER JOB LANGUAGE
- 1. INTRODUCTION
- 2. HOW TO USE PJL
- 3. COMMAND GROUP
- 4. KERNEL COMMANDS
- 5. JOB SEPARATION COMMANDS
- 6. ENVIRONMENT COMMANDS
- 7. STATUS READBACK COMMANDS
- 8. DEVICE ATTENDANCE COMMANDS
- 9. INDEX
- CHAPTER 6 EPSON FX-850
- CHAPTER 7 IBM PROPRINTER XL
- CHAPTER 8 BAR CODE CONTROL
- 1. INTRODUCTION
- 2. PRINT BAR CODES OR EXPANDED CHARACTERS
- 3. DEFINITION OF PARAMETERS
- 3.1. Bar Code Mode
- 3.2. Bar Code Style, Expanded Character Shading, Line Block Drawing & Box Drawing Shading
- 3.3. Bar Code Scaling (Width only)
- 3.4. Bar Code Human Readable Line On or Off
- 3.5. Quiet Zone
- 3.6. Bar Code, Expanded Character Unit, Line Block Drawing & Box Drawing Units
- 3.7. Bar Code, Expanded Character, Line, Block Drawing & Box Drawing Offset in the X-axis
- 3.8. Bar Code & Expanded Character Offset in the Y-axis
- 3.9. Bar Code, Expanded Character, Line, Block Drawing & Box Drawing Height
- 3.10. Expanded Character, Line Block Drawing & Box Drawing Width
- 3.11. Expanded Character Rotation
- 3.12. Bar Code Data Start
- 3.13. Box Drawing
- 3.14. Line Block Drawing
- 3.15. Expanded Character Data Start
- 3.16. Table of Code(EAN) 128 set C
- 4. EXAMPLE PROGRAM LISTINGS
- CHAPTER 9 HP-GL GRAPHICS LANGUAGE
- CHAPTER 10 CARBON COPY FUNCTION
- APPENDIX A COMPARISON LIST
- APPENDIX B FLASH/PCMCIA CARD COMMANDS
- APPENDIX C HBP MODE COMMANDS
- APPENDIX D REFERENCE LIST OF MX-2000/4000/5000/7000 SERIES UNIQUE COMMANDS
- APPENDIX E REFERENCE LIST OF FS-5050 UNIQUE COMMANDS
- APPENDIX F REFERENCE LIST OF SF- 4000 SERIES UNIQUE COMMANDS
CHAPTER 4 HP-GL/2 - 25
7.4. The polygon group
Instruction Function
PM Polygon Mode
EA Edge Absolute Rectangle
ER Edge Relative Rectangle
EP Edge Polygon
EW Edge Wedge
RA Fill Absolute Rectangle
RR Fill Relative Rectangle
WG Fill Wedge
FP Fill Polygon
PM - Polygon mode
PM [ ms ] [;]
This command is used for entering and leaving polygon mode, the mode that allows you to access the
polygon buffer.
When in polygon mode you can use any of the vector group commands to define the vertices of a polygon.
The following commands can be used;
DF, IN, AA, AR, AT, BR, BZ, CI, PA, PD, PE, PR, PU, RT
The polygon you have defined is not printed until you exit polygon mode and fill or edge the polygon.
ms, the mode status, can have the value 0, 1 or 2. If ms = 0 the command empties the polygon buffer and
enters polygon mode. A value of 1 closes the current polygon and remains in polygon mode. All
commands sent following a PM1 before a PM2 or a further PM1 are used to build one sub-polygon. A
value of 2 closes the current polygon or sub-polygon and exits polygon mode.
Having exited polygon mode you can use the EP and FP commands to edge or fill the polygons you have
defined.
The EP command only draws between points defined when the pen was in the down position.
The FP command fills the area between the polygon vertices irrespective of whether the pen was up or down
when the polygon was defined.
The first point in the polygon buffer is the pen position when the PM0 command was invoked.
The next pen position specified after a PM1 command becomes the first vertex of the next sub-polygon.
When plotting a polygon the pen always moves to the first point in the up position.
Using the command with no parameters clears the polygon buffer and enters polygon mode. This is
equivalent to the PM0; command.
If a DF or IN command is invoked in the polygon mode, the printer quits polygon mode, clears the
polygon buffer and executes the subsequent command.
If an ESC E reset command is invoked while the printer is in polygon mode, the printer quits polygon
mode, clears the polygon buffer, exits HP-GL/2 and ejects the page.
EA - Edge rectangle absolute
EA X, Y[;]
X ; X coordinate of opposite corner for the rectangle
Y ; Y coordinate of opposite corner for the rectangle
X and Y coordinates are absolute coordinates in current units.
Plots the rectangle formed by the current position and the opposite corner specified by X and Y.
After plotting, the cursor returns to its point of origin and pen up/down status remains as selected.
Plotting is performed whether the pen is up or down.