Command Reference Guide for Software Developers
Table Of Contents
- Technical Reference Guide
- TABLE OF CONTENTS
- GLOSSARY
- CHAPTER 1 INTRODUCTION
- CHAPTER 2 PCL PRINTER CONTROL LANGUAGE
- 1. COMMAND LIST
- 2. INTRODUCTION
- 3. CONTROLLING THE PRINTER
- 4. JOB CONTROL
- 4.1 . Commands
- 4.1.1. Page size
- 4.1.2. Media type selection
- 4.1.3. Output tray
- 4.1.4. Paper source
- 4.1.5. Left long-edge offset registration
- 4.1.6. Top offset registration
- 4.1.7. Simplex/duplex printing
- 4.1.8. Paper side selection
- 4.1.9. Job separation command
- 4.1.10. Reset
- 4.1.11. Reset to factory default settings
- 4.1.12. Reset to user settings
- 4.1.13. Printer self test
- 4.1.14. Exit current emulation mode
- 4.1.15. Change emulation mode
- 4.2. The Page
- 4.2.1. Physical page
- 4.2.2. Printable area
- 4.2.3. Logical page
- 4.2.4. Text area
- 4.2.5. HP-GL/2 graphics window
- 4.2.6. Portrait page dimensions
- 4.2.7. Landscape page dimensions
- 4.2.8. Coordinates
- 4.2.9. Units
- 4.2.10. Unit of measure
- 4.2.11. Setting the left and right margins
- 4.2.12. Resetting the horizontal margins
- 4.2.13. Setting the top margin
- 4.2.14. Setting the vertical motion index (VMI)
- 4.2.15. Setting the horizontal motion index (HMI)
- 4.2.16. Setting line spacing
- 4.2.17. Text length
- 4.2.18. Page length
- 4.2.19. Perforation skip
- 4.2.20. Positioning the cursor
- 4.2.21. Vertical positioning
- 4.2.22. Horizontal position
- 4.2.23. Positioning the cursor using control codes
- 4.2.24. Using the cursor position stack
- 4.2.25. Half line feed
- 4.2.26. Logical page orientation
- 4.2.27. Text direction
- 4.1 . Commands
- 5. USING FONTS
- 5.1. Introduction
- 5.1.1. Font types
- 5.1.2. Bitmap fonts
- 5.1.3. Scalable fonts
- 5.1.4. Bound fonts
- 5.1.5. Unbound fonts
- 5.1.6. Font sources
- 5.1.7. Internal fonts
- 5.1.8. Card/cartridge fonts
- 5.1.9. Downloadable fonts
- 5.1.10. Primary and secondary fonts
- 5.1.11. Specifying the primary font
- 5.1.12. Specifying the secondary font
- 5.1.13. Selecting the default fonts
- 5.1.14. Switching between the primary and secondary fonts
- 5.1.15. Criteria for font selection
- 5.1.16. Symbol set
- 5.1.17. Symbol collections
- 5.1.18. Type of character spacing
- 5.1.19. Pitch
- 5.1.20. Height
- 5.1.21. Style
- 5.1.22. Stroke weight
- 5.1.23. Typeface
- 5.2. Font Selection Commands
- 5.2.1. User-defined symbol sets
- 5.2.2. Symbol set ID code command
- 5.2.3. Define symbol set
- 5.2.4. Symbol set control command
- 5.2.5. Selecting the symbol set
- 5.2.6. Selecting the type of character spacing
- 5.2.7. Selecting the pitch
- 5.2.8. Selecting the height
- 5.2.9. Scaling the scalable fonts vertically or horizontally
- 5.2.10. Selecting the style
- 5.2.11. Selecting the stroke weight
- 5.2.12. Selecting the typeface
- 5.2.13. Font orientation
- 5.2.14. Transparent print data
- 5.2.15. Esc&d#D (27)(38)(100)#(68) <1Bh><26h><64h>#<44h>
- 5.3. Downloadable font manipulation
- 5.4. Creating Downloadable Fonts
- 5.1. Introduction
- 6. USING GRAPHICS
- 6.1. Source, Pattern and Destination
- 6.2. Plotting Rectangles
- 6.3. Raster Graphics
- 6.3.1. Positioning the cursor
- 6.3.2. Set raster resolution
- 6.3.3. Set high resolution control
- 6.3.4. Set raster image orientation
- 6.3.5. Set raster area height
- 6.3.6. Set raster area width
- 6.3.7. Set raster y-offset
- 6.3.8. Set compression mode
- 6.3.9. Start raster transfer
- 6.3.10. Send raster data
- 6.3.11. Compress transfer graphics
- 6.3.12. End raster transfer
- 6.3.13. Horizontal 1200-dpi image format mode (Raster Graphic Mode 1027)
- 6.4. Vector Graphics
- 6.5. The Picture Frame
- 7. MACROS
- 7.1. The Purpose of a Macro
- 7.2. Defining a Macro
- 7.3. Running a Macro
- 7.4. Handling Macros
- 7.4.1. Delete all macros
- 7.4.2. Delete all temporary macros
- 7.4.3. Delete macro
- 7.4.4. Make macro temporary
- 7.4.5. Make macro permanent
- 7.4.6. Delete all macros from the storage device
- 7.4.7. Delete macro from the storage device
- 7.4.8. Save macro into the storage device
- 7.4.9. Execute data
- 7.4.10. AppleTalk configuration
- 7.4.11. MIO video I/O port control
- 8. STATUS READBACK
- 8.1. Introduction
- 8.2. Memory Status request
- 8.3. Entity Status
- 8.4. Status Response
- 8.5. Status Response Syntax
- 8.5.1. Set status readback location type
- 8.5.2. Set status readback location unit
- 8.5.3. Inquire status readback entity
- 8.5.4. Entity status response
- 8.5.5. Font response
- 8.5.6. Bitmap fonts
- 8.5.7. Bound scalable fonts
- 8.5.8. Unbound scalable fonts
- 8.5.9. Download fonts
- 8.5.10. Location type 1 (currently selected) font
- 8.5.11. Font extended response
- 8.5.12. Macro response
- 8.5.13. Use-defined pattern response
- 8.5.14. Symbol set response
- 8.5.15. Entity error codes
- 8.5.16. Free space command
- 8.5.17. Font cache
- 8.5.18. Memory status response
- 8.5.19. Memory error response
- 8.5.20. Flush all pages command
- 8.5.21. Echo command
- 9. INDEX
- CHAPTER 3 PCL5C
- CHAPTER 4 HP-GL/2 GRAPHICS LANGUAGE
- CHAPTER 5 PJL PRINTER JOB LANGUAGE
- 1. INTRODUCTION
- 2. HOW TO USE PJL
- 3. COMMAND GROUP
- 4. KERNEL COMMANDS
- 5. JOB SEPARATION COMMANDS
- 6. ENVIRONMENT COMMANDS
- 7. STATUS READBACK COMMANDS
- 8. DEVICE ATTENDANCE COMMANDS
- 9. INDEX
- CHAPTER 6 EPSON FX-850
- CHAPTER 7 IBM PROPRINTER XL
- CHAPTER 8 BAR CODE CONTROL
- 1. INTRODUCTION
- 2. PRINT BAR CODES OR EXPANDED CHARACTERS
- 3. DEFINITION OF PARAMETERS
- 3.1. Bar Code Mode
- 3.2. Bar Code Style, Expanded Character Shading, Line Block Drawing & Box Drawing Shading
- 3.3. Bar Code Scaling (Width only)
- 3.4. Bar Code Human Readable Line On or Off
- 3.5. Quiet Zone
- 3.6. Bar Code, Expanded Character Unit, Line Block Drawing & Box Drawing Units
- 3.7. Bar Code, Expanded Character, Line, Block Drawing & Box Drawing Offset in the X-axis
- 3.8. Bar Code & Expanded Character Offset in the Y-axis
- 3.9. Bar Code, Expanded Character, Line, Block Drawing & Box Drawing Height
- 3.10. Expanded Character, Line Block Drawing & Box Drawing Width
- 3.11. Expanded Character Rotation
- 3.12. Bar Code Data Start
- 3.13. Box Drawing
- 3.14. Line Block Drawing
- 3.15. Expanded Character Data Start
- 3.16. Table of Code(EAN) 128 set C
- 4. EXAMPLE PROGRAM LISTINGS
- CHAPTER 9 HP-GL GRAPHICS LANGUAGE
- CHAPTER 10 CARBON COPY FUNCTION
- APPENDIX A COMPARISON LIST
- APPENDIX B FLASH/PCMCIA CARD COMMANDS
- APPENDIX C HBP MODE COMMANDS
- APPENDIX D REFERENCE LIST OF MX-2000/4000/5000/7000 SERIES UNIQUE COMMANDS
- APPENDIX E REFERENCE LIST OF FS-5050 UNIQUE COMMANDS
- APPENDIX F REFERENCE LIST OF SF- 4000 SERIES UNIQUE COMMANDS
CHAPTER 7 IBM PROPRINTER - 6
3. EMULATION DETAILS
The following points should be borne in mind when running the HL Series printers in IBM Proprinter XL
mode.
3.1. Ignored Commands
A few IBM Proprinter XL commands have reduced effect, or no effect at all. In some cases this is due to
the physical nature of an HL Series printer. These commands are as follows. The BEL control code
(ASCII 7) which is used to sound the Proprinter's bell, is ignored. The DC3 control code (ASCII 23),
used to disable the Proprinter, is also ignored. The Esc Y escape sequence, which enables double-speed,
double-density graphics mode has no effect on the printing speed, as HL Series printers always operate as
fast as they can. Hence the Esc Y has the same effect as the Esc L (enable double-density graphics
mode) sequence.
3.2. Resolution
The resolution of the HL Series printers is 600 dots per inch. Some IBM Proprinter commands use
fractions of an inch that not exactly divisible by 600, for example Esc 0 sets line spacing to 1/8" of an
inch. Similarly, the Proprinter graphics commands specify resolutions of 72, 120 and 240 dots per inch.
When a graphic cannot be represented exactly at 600 dots per inch the printer prints the closest possible
approximation to the specified image using 600 dots per inch.
3.3. Character Set selection
Using software commands you can select IBM character set I, IBM character set II or the IBM All
Character Code table. Using the printer control panel you can select a number of other character sets
depending on the printer model, consult the User's Guide to see if this emulation is supported and for a
description of how to do this. All available character sets are shown in the IBM Proprinter XL mode
section of the appendix at the end of this manual.
3.4. Controlling the Printer
Commands are invoked using either control codes or escape sequences. You can send them to the printer
as part of a program, using the same command that you would use to print a text string on the printer.
For example, in BASIC you would use the LPRINT command.
3.5. Control Codes
Control codes are ASCII codes that tell the printer to perform a particular function such as a line feed.
Send a control code to the printer by sending the same type of instruction you would use to print a
character using its ASCII code number. For example, the ASCII code for a form feed is 12, so to get
the printer to perform a form feed use the following BASIC statement:
LPRINT CHR$(12);
The CHR$ operator is normally used to convert an ASCII code into its corresponding character.
3.6. Escape sequences
Escape sequences tell the printer which Proprinter function to perform. An escape sequence consists of
the ESC character followed by one or more characters which define the operation to be performed. Send
an escape sequence to the printer by sending the same type of instruction you would use to print
characters using their ASCII codes. Some escape sequences require parameter values or data following
them, for example, commands which turn a particular feature on and off and commands for downloading
character descriptions to the printer or for printing graphic images. Numerical parameter data, too, is sent
to the printer as if it were a character code to be printed. For example, to set the left and right margin
settings to be at 10 and 70 columns across the page the required escape sequence is Esc X 10 70. In
BASIC this would be:
LPRINT CHR$(27); CHR$(88); CHR$(10); CHR$(70);