User Manual
Table Of Contents
- Product Safety Guide
- How to use this guide:
- Symbols and conventions used in the documentation
- Compilation and Publication Notice
- Choose a safe location for your product
- General precautions
- Connecting the product safely
- Important Information for Australia
- Important Information for New Zealand
- Important Information for Some Countries
- Servicing the product
- Product Warranty & Liability
- Disconnect device
- Approval Information (MFC only)
- Declaration of Conformity (Europe only)
- Declaration of Conformity for R&TTE (Radio and Telecommunications) Directive 1999/5/EC (Europe only) (Applicable to models with telecommunications and/or radio interfaces)
- IEC60825-1:2014 Specification (For 220-240V Models Only)
- Wireless LAN (Models with Wireless LAN function only)
- NFC (Models with NFC function only)
- LAN connection (Network models only)
- Radio interference
- For WLAN models (Taiwan only)
- Compliance Statement of Wireless equipment (Thailand only)
- Recycling information in accordance with the India E-Waste (Management) Rules
- Trademarks
- Open Source Licensing Remarks
- Copyright and License
- Other Information
- Brother Customer Service
- Unlawful use of copying equipment (MFC and DCP only)
17
MFC only A
1 The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has
accepted that the item complies with minimum conditions for connection to its network. It
indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
Above all, it provides no assurance that any item will work correctly in all respects with another
item of Telepermitted equipment of a different make or model, nor does it imply that any
product is compatible with all of Telecom’s network services.
2 This equipment is not capable, under all operating conditions, of correct operation at the higher
speeds for which it is designed. Telecom will accept no responsibility should difficulties arise
in such circumstances.
3 This equipment does not fully meet Telecom's impedance requirements. Performance
limitations may occur when used in conjunction with some parts of the network. Telecom will
accept no responsibility should difficulties arise in such circumstances.
4 This equipment shall not be set up to make automatic calls to the Telecom ‘111’ Emergency
Service.
5 This unit will only work in conjunction with a tone signalling (DTMF) telephone, but some
telephones may not be compatible. Since noise or speech from the telephone can upset
dialling from this unit, errors may result if the devices are used together in other than quiet
conditions.
6 Where it is necessary to dial prefix digits, such as a Caller Display override code (“0196” or
“0197”), this unit will have to be used in conjunction with an associated tone signalling (DTMF)
telephone.
7 Note that some telephones are NOT compatible with this unit and dialling errors may result if
the two devices are used together in other than quiet conditions. The Telecom Faults Service
is NOT to be called should such problems arise. In such cases, it is recommended that the
prefix and wanted number are dialled manually.
8 If a charge for local calls is unacceptable, the ‘Dial’ button should NOT be used for local calls.
Only the 7-digits of the local number should be dialled from your telephone. DO NOT dial the
area code digit or the ‘0’ prefix.
9 This equipment may not provide for the effective hand-over of a call to another device
connected to the same line.
10 Some parameters required for compliance with Telecom’s Telepermit requirements are
dependent on the equipment (PC) associated with this device. The associated equipment shall
be set to operate within the following limits for compliance with Telecom’s Specifications: (a)
There shall be no more than 10 call attempts to the same number within any 30 minute period
for any single manual call initiation, and (b) The equipment shall go on-hook for a period of not
less than 30 seconds between the end of one attempt and the beginning of the next call
attempt.
11 Some parameters required for compliance with Telecom’s Telepermit requirements are
dependent on the equipment (PC) associated with this device. The associated equipment shall
be set to operate within the following limits for compliance with Telecom’s Specifications:
Automatic calls to different numbers are spaced such that there is no less than 5 seconds
between the end of one call attempt and the beginning of another.