Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
9
KE-430B, 431B, 432B, 433B
!0
!1
!2
w
eq
o
i
u
y
t
r
t
u
i
o
y
Table
Cushion collars
Nuts
Flat washers
Rubber collers
3mm
3-2. Installing the control box
1. Remove the 12 screws q, and then open the covers (panel mounting assembly w and main P.C. board
mounting plate e).
NOTE:
When opening the cover, hold it securely so that it does not fall down.
2. Install the control box with the four accessory bolts r, cushions t, cushion collars y, rubber collars u,
flat washers i and nuts o as shown in the illustration above. At this time, leave a gap of approximately 3
mm between the work table and the top of the box.
* Use two nuts o at each installation location, and make sure that both nuts are tightened.
3. Close the covers (panel mounting assembly w and main P.C. board mounting plate e), and tighten them
with the screws q.
* The main P.C. board mounting plate e will be opened again during “3-12. Connecting the cords”, so
provisionally tighten it with the screw q.
4. Install the power switch !0 with the two screws !1.
5. Secure the power switch cord with the three staples !2.
3. INSTALLATION
Cushions
r
!0
t
y
u
i
o
q
e
w
!1
!2
[KE-431B]
0063Q
0052Q
0051Q
Check that the IM sticker is attached to the side of the control box (in the position shown in the illustration).
KE series machine heads can only be used with control boxes which have the IM sticker attached.)
KE-430B
KE-432B
KE-433B