Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
16
KE-430B, 431B, 432B, 433B
e
q
w
[A]
[B]
3-13.Installing the belt cover
1. Loosen the two screws w of the upper cover q.
2. Insert the belt cover e in the direction of the ar-
row, and then secure it with the two screws w and
the two screws r.
* It is not necessary to remove the belt cover e when
tilting back the machine head.
3-14.Installing the foot switch
1. Insert the connector of the foot switch e into the connector w of the control box q.
2. Install the foot switch e to the work table leg !2 with foot switch support plate A r, foot switch support
plate C t, the bolt y, spring washer u, flat washer i, bolt o, spring washer !0 and flat washer !1 as
shown in Figure A.
♦If foot switch support plate B !3 is used in a back-to-front position, it can be used as shown in Figure B.
1. Remove the screw !4 and rubber plug !5.
* Note that the spring !6 will come out when the screw !4 is removed.
2. Turn foot switch support plate B !3 back to front, and then install it with the bolt !7, spring washer !8 and
flat washer !9 as shown in Figure B.
NOTE:
If using the foot switch without installing it to the work table leg, move the foot switch at least 10 mm away from the
leg. If the foot switch is not fully in contact with the work table leg when the foot switch is used, for example, if it is
just hooked loosely onto the work table leg, it may cause the sewing machine to operate incorrectly.
If using the optional two-pedal foot switch, change the setting of DIP switch A on the oreration panel while referring
to “Setting the presser mode” on page 44.
3. INSTALLATION
!6
!0
e
r
t
y
!4
!9
!5
!8
!3
!7
!1
o
u
i
!2
w
q
e
r
0069Q
0071Q
0072Q
0070Q