Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
22
KE-430B, 431B, 432B, 433B
1. Turn on the power switch.
(The POWER indicator will illuminate and the program number will flash in the display window.)
2. Press the TEST switch.
(The TEST indicator will illuminate.)
4. Depress the foot switch to the second step.
Only the feed mechanism will move.
[Check that the needle hole q does not protrude past the frame of the work clamp w.]
* If you depress the foot switch again and keep it depresses after the feed mechanism has started to
move, the feeding speed will increase.
* If you would like to stop the feed while it is moving, press the TEST switch.
5. Press the TEST switch.
(The TEST indicator will switch off and the test mode will be cleared.)
6. Depress the foot switch.
The work clamp will rise and the preparation for sewing will be completed.
TEST
TEST
q
w
1st step
2nd step
6. CHECKING THE SEWING PATTERN
■ When checking by operating only the feed mechanism
To ensure safety during use ......
You can prevent accidental changes being made to
programs by setting DIP switches 7 and 8 to ON.
When DIP switch 7 is ON
... The sewing pattern cannot be enlarged.
When DIP switch 8 is ON
... The program number cannot be changed.
6. CHECKING THE SEWING PATTERN
0090Q
0085Q
0091Q
0092Q
0093Q
0094Q
0095Q
1st step
2nd step
0085Q
3. Depress the foot switch to the second step.
* For two-pedal foot switch, lower the work clamp before depressing the start switch (right
side.)
(The feed mechanism will move to the sewing start position and the program number will
stop flashing.)
* This operation is only carried out the first time that a program has been selected or the size
ratio has been changed.