Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
24
KE-430B, 431B, 432B, 433B
8. To wind more thread onto
the bobbin, loosen the set
screw t and pull the bob-
bin presser q outward.
1. Place the bobbin all the way onto the shaft.
2. Thread the thread as shown in the illustration at
right, wind the thread around the bobbin sev-
eral times in the direction of the arrow, and then
press the bobbin presser q.
3. Turn on the power switch.
(The POWER indicator on the operation panel will illuminate.)
4. Check that the needle is not touching the presser foot,
and then while pressing the BOBBIN. WIND switch w,
depress the foot switch e to start the machine. Keep de-
pressing the foot switch e until the lower thread stops
being wound onto the bobbin.
Release the BOBBIN. WIND switch w after the machine starts operat-
ing. If you release the foot switch before winding is completed, de-
press it once more while pressing and holding the BOBBIN. WIND
switch w.
7. Remove the bobbin,
hook the thread onto
the knife r, and then
pull the bobbin in the
direction of the arrow
to cut the thread.
6. Release the foot switch e.
5. The bobbin presser q will automatically return to its original position after a set amount of thread (80 -
90% of the bobbin capacity) has been wound on.
q
BOBBIN.WIND
ew
Case A
Case B
7-4. Winding the lower thread
Do not touch any of the moving parts or press any objects against the machine while winding the
lower thread, as this may result in personal injury or damage to the machine.
w
q
q
t
r
7. CORRECT USE
<<If the thread winds onto the bobbin unevenly>>
If the thread winds onto the bobbin unevenly, loosen
the nut q and turn the bobbin winder thead tension
stud w to adjust.
* If the thread winds on as shown in A, turn the bob-
bin winder thread tension stud w clokwise; if it
winds on as shown in B, turn the bobbin winder
thead tension stud w counterclockwise.
CAUTION
0103Q
0104Q
0105Q
0107Q
0106Q
0108Q