Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
28
KE-430B, 431B, 432B, 433B
Turn off the power switch at the following times, otherwise the machine may operate if the foot
switch is depressed by mistake, which could result in injury.
• Threading
• When replacing the needle
• When not using the machine and when leaving the machine unattended.
Do not touch any of the moving parts or press any objects against the machine while sewing, as
this may result in personal injury or damage to the machine.
4. Once sewing is completed and the thread has been trimmed, the work clamp q will rise.
1. Turn on the power switch.
(The POWER indicator will illuminate and the program number will flash in the display.)
2. Depress the foot switch to the 2nd step.
The feed mechanism will move to the starting
position and the work clamp q will rise.
* Note that if the foot switch is pressed to the
2nd step while the display is illuminated, the
machine will start operating.
3. Place the material to be sewn under the work clamp
q, and then depress the foot switch.
When the foot switch is pressed to the 1st step,
the work clamp q will lower.
If you would like to shift the position of the mate-
rial, release the foot switch. The work clamp q will
then rise again.
When the foot switch is pressed to the 2nd step,
the machine will start operating.
1st Step
2nd Step
q
q
8. SEWING
Before starting sewing ......
• Check that the needle bar is at its highest position.
Turn the machine pulley so that the index mark q
on the pulley is between the marks w on the belt
cover.
* If the machine pulley stop position is incorrect,
error “E-50” may be displayed, or the wiper may
come into contact with the needle and break the
tip of the needle.
8. SEWING
w
q
CAUTION
0118Q
0085Q
0119Q
0120Q