Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
30
KE-430B, 431B, 432B, 433B
9-3. Lubrication
NOTE1: Fill the machine with oil when the oil level is down to about one-third full in the oil sight glass.
If oil is not added and the oil drops below this level, there is the danger that the machine may seize during
operation.
NOTE2: Be sure to let the machine operate for a while after adding the oil.
NOTE3: If there is no more oil on the felt of the shuttle race base, problems with sewing may result, so add oil to the felt
until it is slightly soaked.
NOTE4: Use only specified Brother oil (Nisseki Sewing Libe 10) for the machine oil.
1. Fill the arm-side oil tank with oil.
* When setting up the sewing machine and when
it hasn’t been used for an extended period of
time, be sure to add 2-3 drops of oil at the place
indicated by the arrow.
2. Fill the bed-side oil tamk with oil.
3. Add oil to the felt q of the shuttle race base.
* When setting up the sewing machine and when
it hasn’t been used for an extended period of
time, be sure to add 2-3 drops oil to the felt.
4. If using the liquid cooling tank w, fill it with silicon
oil (100 mm
2
/s).
9. MAINTENANCE AND INSPECTION
q
w
[KE-432B]
0077Q
0076Q
KE-430B
KE-431B
KE-433B
0078Q
0079Q
0080Q