Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
KE-430B, 431B, 432B, 433B
36
10-7-2. Adjusting the engagement of the movable knife and fixed knife
A. After the movable knife and fixed knife are properly engaged, tighten the screw as shown in Fig.1.
B. Turn the movable knife (in the direction of the arrow) while the screw is still tightened.
C. Loosen the screw.
D. Turn the movable knife (in the direction of the arrow) while the screw is still loosened.
Repeat above steps A, B, C and D four or five times to maintain the cutting performance of the knife.
A
B
C
D
Cutting
edge
Movable knife
Fix knife
17mm
e
w
q
r
10-8.Adjusting the work clamp lift amount
The maximum work clamp lift amount is 17 mm from the top of the needle plate.
The lift amount for each model is adjusted as shown in the table at the time of shipment.
1. To adjust the work clamp lift amount, loosen the bolt q and move the presser arm lever plate w up or
down.
2. Apply grease to the bottom of the presser plate e to the top of the presser arm lever plate w and to the
sliding part of the work clamp r (grease is already applied at the time of shipment), and check that the
movement becomes easier.
3. Check that there is a gap between the presser arm lever plate w and the presser plate e when the work
clamp r is lowered.
* If movement is sluggish when the work clamp r is being raised and lowered, it may not be possible to
increase the work clamp r lift amount.
* If the work clamp r cannot be raised or lowered, error code “E-61” or “E-63” will be displayed.
10. STANDARD ADJUSTMENTS
Fig. 1
Cutting
edge
Cutting
edge
Cutting
edge
[KE-430B, 431B, 433B]
-2,-3
10
mm
+1
0
Lift amount
-1,-5
10 mm
-2
14
mm
-7
9
mm
spec.
+1
0
+1
0
+1
0
-1
10 mm
-2
14
mm
-7
9
mm
KE-431BKE-430B KE-433B
+1
0
+1
0
+1
0
0148Q 0150Q
0149Q
0151Q 0152Q