Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
KE-430B, 431B, 432B, 433B
37
[KE-432B]
The maximum work clamp lift amount is 17 mm from the top of the needle plate when the machine is stopped.
The lift amount is adjusted 13
+
1
0
mm at the time of shipment.
While the machine is stopped, loosen the bolt q and move the presser roller attachment plate w vertically to
adjust the lift amount.
* When making this adjustment, check to see if the work clamp will open. Also, readjust the closing distance
of the work clamp according to the second procedure of “10-10. Work clamp closing-distance adjustment”.
* Loosen the nut t and turn the stop lever adjusting screw y to adjust the position of the stop lever e so that
it does not touch the adjusting ring r when the work clamp is raised.
* If the work clamp cannot be raised or lowered, error code “E-61” or “E-63” will be displayed.
10-9.Work clamp pressure adjustment (KE-432B)
Loosen the lower adjusting ring q as much as pos-
sible (to the extent that the material being sewn does
not slip and alter the pattern). Then, adjust the pres-
sure by turning the upper adjusting ring w.
■ Removal of the work clamp spring....
Lower the work clamp, then place the adjusting ring
e in the hole of the frame, remove the tip of the
adjusting screw from the lever holder r, and re-
move the work clamp spring t.
w
q
w
q
r
e
t
10. STANDARD ADJUSTMENTS
17mm
y
t
e
r
0153Q 0154Q
0155Q
0156Q