Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
KE-430B, 431B, 432B, 433B
42
SELECT
PROGRAM NO.
RESET
COUNTER
X
-
SCALE
Y
-
SCALE
SPEED
P
TEST
BOBBIN.WIND
P4P3
P1 P2
POWER
r
e
q
y
t
o
w
u
i
10-17. Moving stitch patterns
· Programs which have already been programmed can be moved up, down and to the left and right. (How-
ever, such patterns will be reset if the power supply is turned off or the program number is changed.)
· The feed position can be set to the any position desired.
1. Select the program number, and then press the start switch once to move the feed mechanism to the
sewing start position.
2. Press the SELECT switch q until the PROGRAM NO. indicator w illuminates.
3. While pressing the TEST switch e, press the RESET switch r.
* The TEST indicator t will illuminate and < > will appear in the display window y.
4. Press the SELECT switch q so that either the X-SCALE indicator u or Y-SCALE indicator i illuminates.
5. Press the DISPLAY SET switches o to move the feed mechanism one pulse at a time.
• If the DISPLAY SET ( ) switch is pressed while the X-SCALE indicator is illuminated, the feed mecha-
nism will move to the left.
• If the DISPLAY SET ( ) switch is pressed while the X-SCALE indicator is illuminated, the feed mecha-
nism will move to the right.
• If the DISPLAY SET ( ) switch is pressed while the Y-SCALE indicator is illuminated, the feed mecha-
nism will move down.
• If the DISPLAY SET ( ) switch is pressed while the Y-SCALE indicator is illuminated, the feed mecha-
nism will move up.
6. When the TEST switch e is pressed after the above fine adjustments have been made, the TEST indicator
t and display window y will both switch off and movement of the stitch pattern will be completed.
NOTE:
When moving the stitch pattern, take the whole of the pattern area into consideration so that no parts extend outside
the sewing area when the pattern is sewn.
* If you would like to set the feed position to a desired position, carry out steps 2. to 6. above while the display window
y is flashing. The stitch pattern will not be moved at this time.
10. STANDARD ADJUSTMENTS
0583Q