Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
KE-430B, 431B, 432B, 433B
46
12-4.Using user programs
Recording a user program
11. Press the SELECT switch e. * This completes the recording of user program No.1.
* “PP 2” will then appear in the display window o, to indicate that user program No.2 is now being recorded.
Repeat steps 3. through to 11. to record further programs as desired.
10. Press the DISPLAY SET switches !0 to select the speed setting that you would like to record.
9. Press the SELECT switch e. * The SPEED indicator u will illuminate.
8. Press the DISPLAY SET switches !0 to select the Y scale setting that you would like to record.
7. Press the SELECT switch e. * The Y-SCALE indicator y will illuminate.
6. Press the DISPLAY SET swithes !0 to select the X scale setting that you would like to record.
5. Press the SELECT switch e. * The X-SCALE indicator t will illuminate.
4. Press the DISPLAY SET switches !0 to select the number for the program that you would like to record.
3. Press the SELECT switch e .
* The PROGRAM NO. indicator r will illuminate.
2. Turn on the power switch.
While pressing the TEST switch w, press the SE-
LECT switch e.
* All of the menu indicators (r to i) will illuminate and the
mode will switch to recording mode.
* In addition, “PP 1” will appear in the display window o to
indicate that user program No.1 is being recorded. (Once
recording of No.1 is completed, No.2 will be displayed; once
No.2 is completed, No.3 will be displayed. Thus the next
unrecorded program letter is always displayed.)
q
!1
SELECT
PROGRAM NO.
RESET
COUNTER
X
-
SCALE
Y
-
SCALE
SPEED
P
TEST
BOBBIN.WIND
P4P3
P1 P2
POWER
o
!0
e
!2
r
t
y
u
i
1. Turn off the power switch and then set DIP switch
A-3 of the DIP switches q to ON.
12. CHANGING FUNCTIONS USING THE DIP SWITCHES
User program ...
It can store sixteen different programs which can include details such as the program number, X scale, Y
scale and sewing speed. If you are sewing certain patterns over and aver again, it is useful to record the
settings for these patterns into a user program.
w
0587Q
0179Q
12. Press the TEST switch w. This completes the recording.
* The menu indicators (e to i) will all illuminate and “p1” will appear in the display to indicate that user program No.1 is
currently selected.