Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
![](/manual/brother/ke-430b/1-instruction-manual-english/images/img-53.png)
KE-430B, 431B, 432B, 433B
48
SELECT
PROGRAM NO.
RESET
COUNTER
X
-
SCALE
Y
-
SCALE
SPEED
P
TEST
BOBBIN.WIND
P4P3
P1 P2
POWER
memo-00
memo-01
memo-02
memo-03
memo-04
memo-05
memo-06
memo-07
memo-08
memo-09
memo-0A
memo-0b
memo-0c
memo-0d
memo-0E
memo-0F
Motion when set to ON
At the end of sewing, the feed plate will be returned to the sewing start point via
mechanical home position.
Work clamp will move to the sewing start point, and then will be lifted.
(The work clamp rises at the final stitch to enable the quick taking out of the
workpieces.)
Feed will move automatically to the next starting point at the same time as a user
program is switched.
(Normally it moves to the starting point after sewing starts.)
When sewing using programs, the programs which have been set will be sewn in
numerical order. (Cycle sewing mode is set.)
The sewing speed will be fixed at the minimum speed for the maximum pitch of the
sewing data. (Set this to ON if you are concerned that vartations in pitch may cause
changes in the sewing speed.)
Increases the presser solenoid lifting force (Set to ON when using the optional
spring for extra-heavy material)
Enlargement and reduction ratio settings for X and Y become the same.
–
Test feeding is carried out stitch by stitch when the foot switch is depressed.
The sewing start point becomes the reference point for enlargements and
reductions. (The reference point for enlargements and reductions is normally the
center of the sewing frame.)
Work clamp does not close.
Work clamp closes when it is lower.
Needle stops in up position during emergency stop.
(EMERGENCY STOP switch is available as an option.)
The bar tacking stitches (with a pitch of less than 1 mm) are also enlarged and
reduced. (Normally stitches with a pitch of less than 1 mm are not enlarged or
reduced.)
Test feeding will be performed at the same speed as that for actual sewing.
(This is used for checking feeding operation.)
After sewing is finished, the work clamp automatically opens and closes once
(practice operation).
Switch
*
*
r
t
w
y
e
13.
CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
The functions of the switches on the operation panel q can be changed to carry out special functions.
NOTE:
After changing the memory switch settings, press the power switch to turn the power off and then back on again.
The memory switches “00 - 2F” are set to OFF at the time of shipment.
1. Turn on the power switch.
2. While pressing the TEST switch w, press the BOB-
BIN. WIND switch e.
* “00 - -” will appear in the display window r.
3. Press the DISPLAY SET switches t to set the two
digits at the left of the display window r to the
corresponding number (00 to 4F) of the function
shown in the table below that you would like to
select.
4. When the BOBBIN. WIND switch e is pressed, the
two spaces at the right in the display window will
change from “- -” to “ON”.
* If you press the RESET switch y at this time,
memory switches from 00 to 2F will all be set to
OFF (“--”), and memory switches from 30 to 4F
will be returned to their initial settings.
5. Press the TEST switch w.
* The display will return to normal.
■ Memory switches 00 - 0F
13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
*KE-432B only.
q
0588Q