Instruction manual
Table Of Contents
- Go to Instruction Manual Top Page
- Cover-Top
- SAFETY INSTRUCTIONS
- CONTENTS
- 1. NAME OF EACH PART
- 2. SPECIFICATIONS
- 3. INSTALLATION
- 3-1. Power table
- 3-2. Installing the control box
- 3-3. Installing the rubber cushions
- 3-4. Installing the oil pan
- 3-5. Installing the cushions
- 3-6. Installing the switching plate
- 3-7. Installing the machine head
- 3-8. Installing the head rest
- 3-9. Installing the liquid cooling tank, optional
- 3-10.Installing the operation panel
- 3-11.Connecting the ground wire
- 3-12.Connecting the cords
- 3-13.Installing the belt cover
- 3-14.Installing the foot switch
- 3-15.Installing the spool stand
- 3-16.Installing the eye guard
- 4. LUBRICATION
- 5. OPERATION
- 6. CHECKING THE SEWING PATTERN
- 7. CORRECT USE
- 8. SEWING
- 9. MAINTENANCE AND INSPECTION
- 10. STANDARD ADJUSTMENTS
- 10-1.Adjusting the needle bar height
- 10-2.Adjusting the needle bar lift amount
- 10-3.Adjusting the driver needle guard
- 10-4.Adjusting the needle clearance
- 10-5.Adjusting the shuttle race thread guide
- 10-6.Adjusting the thread take-up amount
- 10-7.Adjusting the movable knife
- 10-8.Adjusting the work clamp lift amount
- 10-9.Work clamp pressure adjustment (KE-432B)
- 10-10. Work clamp closing-distance adjustment (KE-432B)
- 10-11. Work clamp interchangeability (KE-433B)
- 10-12. Adjusting the needle up stop position
- 10-13. Adjusting the thread wiper
- 10-14. Checking the input sensor and DIP switch input
- 10-15. Checking the input voltage
- 10-16. Clearing all memory settings
- 10-17. Moving stitch patterns
- 11. USING THE COUNTERS
- 12. CHANGING FUNCTIONS USING THE DIP SWITCHES
- 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
- 14. TABLE OF ERROR CODES
- 15. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
- 16. TROUBLESHOOTING
- 17. OPTIONAL PARTS
- Cover-Last
3
KE-430B, 431B, 432B, 433B
2-2. Program list
Sewing patterns are limited as shown in the table below. (Any program is available as long as the sewing
pattern is within the work clamp and feed plate in size.)
The sewing size is the length when the enlargement/reduction ratio is 100%.
[KE-430B]
-1
-5
-2
Use
For ordinary
materials
For denim
Program No.
1
4
5
8
13
15
20
21
2
3
6
14
16
17
18
19
Sewing pattern
No. of
stitches
42
30
29
21
35
42
28
35
42
35
30
35
43
42
56
64
Standard bar
tacking length
16mm
16mm
10mm
7mm
10mm
10mm
7mm
7mm
20mm
20mm
16mm
16mm
16mm
24mm
24mm
24mm
Standard bar
tacking width
2mm
2mm
2mm
2mm
2mm
2mm
2mm
2mm
3mm
3mm
3mm
3mm
3mm
3mm
3mm
3mm
Specifica-
tion
2. SPECIFICATIONS
* The difference between -1 and -5 specifications for ordinary material is that the standard work clamp and
feed plate are different.