Network User's Guide
Table Of Contents
- NETWORK USER’S GUIDE
- Table of Contents
- 1 Introduction
- 2 Configuring your machine for a network with an Ethernet cable connection (Not available for MFC-253CW, MFC-255CW and MFC-257CW)
- Overview
- IP addresses, subnet masks and gateways
- Step by step chart
- Setting up the IP address and subnet mask
- Changing the print server settings
- Using the BRAdmin Light utility to change the print server settings
- Using the BRAdmin Professional 3 utility to change the wireless settings (Windows®)
- Using the Remote Setup to change the print server settings (Not available for Windows Server® 2003/2008) (Not available for DCP models, MFC-253CW, MFC-255CW, MFC-257CW and MFC-295CN)
- Using the control panel to change the print server settings
- 3 Configuring your machine for a wireless network (Not available for DCP-365CN, DCP-395CN and MFC-295CN)
- Overview
- Wireless network terms and concepts
- Step by step chart for wireless network configuration
- Confirm your network environment
- Confirm your wireless network setup method
- Configuration using the machine’s control panel Setup Wizard to configure your wireless network machine
- Configuration using the SES/WPS/AOSS control panel menu (Infrastructure mode only)
- Configuration using the PIN Method of Wi-Fi Protected Setup™ (Infrastructure mode only)
- Configuration using the Brother installer application on the CD-ROM to configure your wireless network machine
- Configuring your machine for a wireless network
- Using the Setup Wizard from the control panel
- Using SES, WPS or AOSS from the control panel menu to configure your machine for a wireless network
- Using the PIN Method of Wi-Fi Protected Setup™
- Using the Brother automatic installer application on the CD-ROM to configure your machine for a wireless network
- 4 Wireless configuration for Windows® using the Brother installer application (For DCP-373CW, DCP-375CW, DCP-377CW, DCP-593CW, DCP-595CW, DCP-597CW, MFC-495CW and MFC-795CW)
- 5 Wireless Configuration for Macintosh using the Brother installer application (For DCP-373CW, DCP-375CW, DCP-377CW, DCP-593CW, DCP-595CW, DCP-597CW, MFC-495CW and MFC-795CW)
- 6 Control panel setup
- Network menu
- TCP/IP
- Setup Wizard (For wireless models)
- SES/WPS/AOSS (For wireless models)
- WPS w/PIN code (For wireless models)
- WLAN Status (For wireless models)
- Ethernet (Not available for MFC-253CW, MFC-255CW and MFC-257CW)
- MAC Address
- Network I/F (For wireless models, not available for MFC-253CW, MFC-255CW and MFC-257CW)
- WLAN Enable (For MFC-253CW, MFC-255CW and MFC-257CW)
- Restoring the network settings to factory default
- Printing the Network Configuration List
- Network menu
- 7 Driver Deployment Wizard (Windows® only)
- 8 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 9 Network printing from a Macintosh
- 10 Troubleshooting
- Appendix A
- Appendix B
- Appendix C
- Index
Troubleshooting
132
10
e If you have tried steps a to d above and it does not work, then reset the print server back to the default
factory settings and try from the initial setup again. For information how to reset to the default factory
settings, see Restoring the network settings to factory default on page 114.
f Check the following:
If the installation failed, the Firewall on your computer may be blocking the necessary network
connection to the machine. In this case, you will need to disable the Firewall on your computer and re-
install the drivers. For more information, see General problems on page 129. If you are using personal
Firewall software, see the User’s Guide for your software or contact the software manufacturer.