Network User's Guide
Table Of Contents
- NETWORK USER’S GUIDE
- Table of Contents
- 1 Introduction
- 2 Configuring your machine for a network with an Ethernet cable connection
- Overview
- IP addresses, subnet masks and gateways
- Step by step chart
- Setting up the IP address and subnet mask
- Changing the print server settings
- Using the BRAdmin Light utility to change the print server settings
- Using the BRAdmin Professional utility to change the wireless settings (For Windows®)
- Using the Remote Setup to change the print server settings (Not available for DCP models)
- Using the control panel to change the print server settings
- 3 Configuring your machine for a wireless network (Not available for MFC-5490CN and MFC-5890CN)
- Overview
- Wireless network terms and concepts
- Step by step chart for wireless network configuration
- Confirm your network environment
- Confirm your wireless network setup method
- Configuration using the machine’s control panel Setup Wizard to configure your wireless network machine
- Configuration using the SES/WPS/AOSS control panel menu (Infrastructure mode only)
- Configuration using the PIN Method of Wi-Fi Protected Setup™ (Infrastructure mode only)
- Configuration using the Brother installer application on the CD-ROM to configure your wireless network machine
- Configuring your machine for a wireless network
- 4 Wireless configuration for Windows® using the Brother installer application (Not available for MFC-5490CN and MFC-5890CN)
- 5 Wireless Configuration for Macintosh® using the Brother installer application (Not available for MFC-5490CN and MFC-5890CN)
- 6 Control panel setup
- Network menu
- TCP/IP
- Setup Misc. (MFC-5490CN only)
- Setup Wizard (wireless network only)
- SES/WPS/AOSS (wireless network only)
- WPS w/PIN code (wireless network only)
- WLAN Status (wireless network only)
- Ethernet (wired network only)
- E-mail/I-FAX (For MFC-6490CW and MFC-6890CDW)
- Scan to FTP (For MFC-5890CN and MFC-6490CW)
- Scan to FTP (For MFC-6890CDW)
- Time Zone (For MFC-6490CW and MFC-6890CDW)
- Network I/F (Not available for MFC-5490CN and MFC-5890CN)
- LDAP (For MFC-6890CDW)
- Restoring the network settings to factory default
- Printing the Network Configuration List
- Network menu
- 7 Driver Deployment Wizard (Windows® only)
- 8 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 9 Network printing from a Macintosh®
- 10 LDAP operation (For MFC-6890CDW)
- 11 Internet fax and Scan to E-mail (For MFC-6490CW and MFC-6890CDW)
- Internet fax overview
- Getting connected
- Control panel key functions
- Sending an Internet fax
- Manually entering text
- Receiving E-mail or Internet fax
- Receiving an Internet fax to your computer
- Forwarding received E-mail and fax messages
- Relay broadcasting
- TX Verification Mail
- Setup Mail TX
- Setup Mail RX
- Error mail
- Important information on Internet fax
- Scan to E-mail Server overview (MFC-6490CW and MFC-6890CDW)
- Internet fax overview
- 12 Security features (For MFC-6490CW and MFC-6890CDW)
- 13 Troubleshooting
- Appendix A
- Appendix B
- Appendix C
- Index
Control panel setup
77
6
e Press a or b to choose BOOT Method.
Press OK.
f Press d or c to choose Auto
1
, Static
2
, RARP
3
, BOOTP
4
or DHCP
5
.
Press OK.
g Press Stop/Exit.
For MFC-5490CN 6
a Press Menu, 5, 1, 1.
b Press d or c to choose Auto
1
, Static
2
, RARP
3
, BOOTP
4
or DHCP
5
.
Press OK.
c Press Stop/Exit.
For Touchscreen models 6
a Press MENU.
b Press Network.
c (For Wired) Press Wired LAN.
(For Wireless) Press WLAN.
d Press TCP/IP.
e Press BOOT Method.
f Press Auto
1
, Static
2
, RARP
3
, BOOTP
4
or DHCP
5
.
g Press Stop/Exit.
1
Auto mode
In this mode, the machine will scan the network for a DHCP server, if it can find one, and if the DHCP server is configured to allocate an IP address
to the machine, then the IP address supplied by the DHCP server will be used. If no DHCP server is available, then the machine will scan for a
BOOTP server. If a BOOTP server is available, and it is configured correctly, the machine will take its IP address from the BOOTP server. If a
BOOTP server is not available, the machine will scan for a RARP server. If a RARP server also does not answer, the IP Address is set using the
APIPA protocol, see Using APIPA to configure the IP address on page 166. After the machine is initially powered ON, it may take a few minutes
for the machine to scan the network for a server.
2
Static mode
In this mode the machine’s IP address must be manually assigned. Once entered the IP address is locked to the assigned address.
3
RARP mode
The Brother print server IP address can be configured using the Reverse ARP (RARP) service on your host computer. For more information on
RARP, see Using RARP to configure the IP address on page 166.
4
BOOTP mode
BOOTP is an alternative to RARP that has the advantage of allowing configuration of the subnet mask and gateway. For more information on
BOOTP, see Using BOOTP to configure the IP address on page 165.
5
DHCP mode (DHCP)
Dynamic Host Configuration Protocol (DHCP) is one of several automated mechanisms for IP address allocation. If you have a DHCP server in
your network (typically a UNIX
®
, Windows
®
2000/XP, Windows Vista
®
network) the print server will automatically obtain its IP address from a
DHCP server and register its name with any RFC 1001 and 1002 compliant dynamic name services.