Quick Setup Guide Start Here MFC-8710DW MFC-8810DW MFC-8910DW Thank you for choosing Brother, your support is important to us and we value your business. Your Brother product is engineered and manufactured to the highest standards to deliver reliable performance, day-in and day-out. Please read the Product Safety Guide first, then read this Quick Setup Guide for the correct setup and installation procedure. To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/.
WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injuries. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injuries. WARNING • Plastic bags are used in the packing of your machine. Plastic bags are not toys. To avoid the danger of suffocation, keep these bags away from babies and children and dispose of them correctly.
Note • Keep a minimum gap around the machine as shown in the illustration. 15.70 in. (400 mm) 6.00 in. (150 mm) 6.00 in. (150 mm) 6.00 in. (150 mm) • The components included in the box may differ depending on your country. • We recommend that you save the original packaging. • If for any reason you must ship your machine, carefully repack the machine in the original packaging to avoid any damage during transit. The machine should be adequately insured with the carrier.
2 Remove the packing material from the machine d Take out the drum unit and toner cartridge assembly. Important DO NOT connect the AC power cord yet. a b c Remove the packing tape from the outside of the machine and the film covering the scanner glass. Open the MP tray a, and remove the packing tape b from the MP tray support, then close the MP tray. e Press the front cover release button and open the front cover. Remove the silica gel pack a.
a b 3 Load paper in the paper tray c d Pull the paper tray completely out of the machine. Fan the stack of paper well to avoid paper jams and misfeeds. Put the paper in the tray and make sure: The paper is below the maximum paper mark (bbb) a. Over filling the paper tray will cause paper jams. The side to be printed on is face down. The paper guides touch the sides of the paper so it will feed properly.
4 Connect the power cord and telephone line Important DO NOT connect the interface cable yet. a b Connect the AC power cord to the machine and then plug it into an AC power outlet. Turn the machine's power switch on. WARNING The machine must be grounded using a 3-prong plug.
Note If you are sharing one telephone line with an external telephone answering machine, connect it as shown below. Before you connect the external telephone answering machine, remove the protective cap c from the EXT. jack on the machine. a 5 Wireless setup (if needed) When the Wi-Fi setup message appears, press OK. Do one of the following: If you are using a Macintosh computer or a mobile device on a wireless network, go to b.
a b c 8 6 Choose your language (if needed) Press Menu, 0, 0. Press a or b to choose your language. Press OK. Press Stop/Exit.
7 Choose the correct Receive Mode The correct Receive Mode is determined by the external devices and telephone subscriber services (Voice Mail, Distinctive Ring, etc.) you have (or will be using) on the same line as the Brother machine. Will you be using a Distinctive Ring number for receiving faxes? Brother uses the term “Distinctive Ring” but telephone companies may have other names for this service such as Custom Ringing, RingMaster, Personalized Ring, Teen Ring, Ident-A-Call, and Smart Ring.
8 Set the LCD contrast (if needed) d 02.Date&Time 03/XX/2012 If you are having difficulty reading the LCD, try changing the contrast setting. a b —OR— Press d to decrease the contrast. c Day:25 Enter & OK Key Press Menu, 1, 7. Press c to increase the contrast. (e.g. Enter 2, 5 for 25th.) e Press OK. Press Stop/Exit. 9 Set the date and time Press Menu, 0, 2, 1. Do one of the following: If you want to use the 24-hour clock, press a or b to choose 24h Clock, and then press OK. Go to step f.
h Press a or b to choose AM or PM, and then press OK. 02.Date&Time 03/25/2012 03:25 a AM b PM Select ab or OK (e.g. Choose PM for 3:25 P.M.) i Press Stop/Exit. 10 Note • See the following chart for entering your name. • If you need to enter a character that is on the same key as the last character, press c to move the cursor to the right. • If you entered a character incorrectly and want to change it, press d or c to move the cursor to the incorrect character, then press Clear.
11 Fax Transmission Report Your Brother machine is equipped with a Transmission Verification Report that can be used as confirmation that you sent a fax. This report lists the name or fax number of the receiving party, the date, time and duration of the transmission, the number of pages transmitted, and whether or not the transmission was successful. If you want to use the Fax Transmission Report feature see Printing reports in the Advanced User's Guide.
14 Dial Prefix The dial prefix setting will automatically dial a predefined number before every fax number you dial. For example: If your phone system requires a 9 to dial an outside number this setting will automatically dial 9 for every fax you send. a b Press Menu, 0, 5. (For Canada, press Menu, 0, 6.) Enter the prefix number (up to 5 digits) on the dial pad, and then press OK. Note • You can use the numbers 0 to 9, #, l and !. (Press Hook to display “!”.
17 Send in the Product Registration and Test Sheet (USA only) You can also register your product online using the On-Line Registration link from the installer CD-ROM or visit http://www.brother.com/registration/. a b c d e Fill out the Product Registration and Test Sheet. Put the sheet face up in the ADF (Automatic Document Feeder) or face down on the scanner glass. Make sure (FAX) is illuminated in Blue. Enter the toll-free fax number: 1-877-268-9575. Press Start.
18 Choose your connection type These installation instructions are for Windows® XP Home/Windows® XP Professional, Windows® XP Professional x64 Edition, Windows Vista®, Windows® 7, and Mac OS X (versions 10.5.8, 10.6.x and 10.7.x). Note • For Windows Server® 2003/2003 x64 Edition/2008/2008 R2 and Linux®, visit your model page at http://solutions.brother.com/. • You can visit us at http://solutions.brother.
USB Windows® For USB Interface Users (Windows® XP/XP Professional x64 Edition/Windows Vista®/ Windows® 7) 19 a Before you install Make sure that your computer is ON and you are logged on with Administrator rights. 20 a Important • If there are any programs running, close them. • The screens may differ depending on your operating system. Note The installer CD-ROM includes Nuance™ PaperPort™ 12SE.
USB d Follow the on-screen instructions until this screen appears. Windows® 21 a Finish and restart Click Finish to restart your computer. After restarting the computer, you must log on with Administrator rights. Note e Connect the USB cable to the USB port marked with the symbol on your machine and then connect the cable to your computer.
USB Macintosh For USB Interface Users (Mac OS X 10.5.8 - 10.7.x) 19 a Before you install Make sure your machine is connected to the power and your Macintosh is ON. You must be logged on with Administrator rights. Important 20 a b Install MFL-Pro Suite Put the installer CD-ROM into your CD-ROM drive. Double-click the Start Here OSX icon. If prompted, select your model. For users of Mac OS X 10.5.7 or lower, upgrade to Mac OS X 10.5.8 - 10.7.x.
USB 21 Macintosh Download and install Presto! PageManager When Presto! PageManager is installed OCR capability is added to Brother ControlCenter2. You can easily scan, share and organize photos and documents using Presto! PageManager. a On the Brother Support screen, click Presto! PageManager and follow the on-screen instructions. Macintosh 19 Windows® The installation is now complete.
Wired Network Windows® For Wired Network Interface Users (Windows® XP/XP Professional x64 Edition/Windows Vista®/ Windows® 7) 19 a Before you install c Connect the network interface cable to the Ethernet port and then connect it to a free port on your hub. Make sure that your computer is ON and you are logged on with Administrator rights. Important • If there are any programs running, close them. • The screens may differ depending on your operating system.
Wired Network c Windows® Choose Wired Network Connection (Ethernet) and then click Next. Note • If prompted, choose your machine from the list, and then click Next. Note If you want to install the PS driver (BR-Script3 printer driver), choose Custom Install and then follow the on-screen instructions. d • If your machine is not found over the network, confirm your settings by following the on-screen instructions.
Wired Network 22 Install MFL-Pro Suite on additional computers (if needed) If you want to use your machine with multiple computers on the network, install MFL-Pro Suite on each computer. Go to step 20 on page 20. Note Network license (Windows®) This product includes a PC license for up to 5 users. This license supports the installation of the MFL-Pro Suite including Nuance™ PaperPort™ 12SE on up to 5 PCs on the network.
Wired Network Macintosh For Wired Network Interface Users (Mac OS X 10.5.8 - 10.7.x) 19 a Before you install Make sure your machine is connected to the power and your Macintosh is ON. You must be logged on with Administrator rights. Important 20 a b Install MFL-Pro Suite Put the installer CD-ROM into your CD-ROM drive. Double-click the Start Here OSX icon. If prompted, select your model. For users of Mac OS X 10.5.7 or lower, upgrade to Mac OS X 10.5.8 - 10.7.x.
Wired Network Note • You can find your machine’s MAC Address (Ethernet Address) and IP Address by printing out the Network Configuration Report. See Print the Network Configuration Report on page 41. • If this screen appears click OK. 1) Enter a name for your Macintosh in Display Name (up to 15 characters long). Macintosh 21 Download and install Presto! PageManager When Presto! PageManager is installed OCR capability is added to Brother ControlCenter2.
For Wireless Network Users For Wireless Network Interface Users 19 Before you begin First you must configure the wireless network settings of your machine to communicate with your wireless access point/router. After the machine is configured to communicate with your wireless access point/router, computers and mobile devices on your network will have access to the machine. To use the machine from a computer, you will need to install the drivers and software.
For Wireless Network Users 20 Choose your wireless setup method The following instructions will offer three methods for setting up your Brother machine on a wireless network. If you began the wireless setup from step 5 on page 7 (for Macintosh and mobile devices), go to method b (Setup Wizard). For all other users, choose the method you prefer for your environment. Note To setup your machine in any other wireless environment, you can find instructions in the Network User's Guide.
For Wireless Network Users b Manual setup from the control panel using the Setup Wizard (Macintosh, mobile devices and Windows®) If your wireless access point/router does not support WPS (Wi-Fi Protected Setup™) or AOSS™, write down the wireless network settings of your wireless access point/router in the area below. Important Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings.
For Wireless Network Users Setup using the Installer CD-ROM and temporarily using a USB cable (Windows® only) 21 Setup the wireless settings c Choose Wireless Network Connection and then click Next. Note If you want to install the PS driver (BR-Script3 printer driver), choose Custom Install and then follow the on-screen instructions. Important • You must use a USB cable temporarily during configuration.
For Wireless Network Users f Connect the USB cable directly to the computer and the machine (you must remove the USB cable in step l, on this page). g h i j Enter the Network Key you wrote down in step 20-a on page 26, and then click Next. Note Do one of the following: If the Installation confirmation screen appears, check the box and click Next, go to h. Otherwise, go to i. Check Yes if you want to connect with the listed SSID. Click Next and go to k.
For Wireless Network Users Manual setup from the control panel using the Setup Wizard (Macintosh, mobile devices and Windows®) 21 If you are using an authentication and encryption method that requires a Network Key, go to g. If your authentication method is Open System and your encryption mode is None, go to h. Setup the wireless settings Important Note You must have the wireless settings you wrote down for your network in step 20-b on page 27 before you proceed.
For Wireless Network Users Wireless setup is now complete. A four level indicator at the top right of your machine’s LCD will show the wireless signal strength of your wireless access point/router. For computer users, please install MFL-Pro Suite. For Macintosh Users: Now go to step 22 on page 39 For Windows® Users: Now go to step 22 on page 37 For mobile device users who began the setup from step 5 on page 7, go back to step 6 to continue the machine settings.
For Wireless Network Users One push setup using WPS (Wi-Fi Protected Setup) or AOSS™ (Windows® and Macintosh) 21 a Note Configure the wireless settings If your wireless access point/router supports WPS (PIN Method) and you want to configure your machine using the PIN (Personal Identification Number) Method, see Configuration using the PIN Method of WPS (Wi-Fi Protected Setup) in the Network User's Guide. Confirm your wireless access point/router has the WPS or AOSS™ symbol as shown below.
For Wireless Network Users Troubleshooting Important Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings. How can I find the wireless settings (Network Name (SSID) and Network Key) 1. You should see the documentation provided with your wireless access point/router. 2. The initial network name could be the manufacturer’s name or the model name. 3.
For Wireless Network Users Error code Recommended Solutions The wireless network and security setting you entered may be incorrect. Reconfirm the wireless network settings. TS-03 * Check if the entered or selected SSID/authentication method/encryption method/UserID/Userpass are correct. See How can I find the wireless settings (Network Name (SSID) and Network Key) on page 33 to confirm.
For Wireless Network Users Error code Recommended Solutions The machine cannot detect a wireless access point/router that has WPS or AOSS™ enabled. If you would like to configure your wireless settings using WPS or AOSS™, you must operate both your machine and the wireless access point/router. Confirm your wireless access point/router supports WPS or AOSS™ and try starting again.
For Wireless Network Users Entering Text for Wireless Settings Most number keys have three or four letters printed on them. The keys for 0, # and l do not have printed letters because they are used for special characters. By pressing the proper number key repeatedly, you can access the character you want.
Wireless Network Windows® Install the Drivers & Software (Windows® XP/XP Professional x64 Edition/Windows Vista®/ Windows® 7) 22 a Before you install b Click Install MFL-Pro Suite, and click Yes if you accept the license agreements. Make sure that your computer is ON and you are logged on with Administrator rights. Important • If there are any programs running, close them. • The screens may differ depending on your operating system. Note • The installer CD-ROM includes Nuance™ PaperPort™ 12SE.
Wireless Network e Choose the machine from the list, and then click Next. Note The installation will automatically continue. The installation screens appear one after another. If prompted, follow any on-screen instructions. Important DO NOT cancel any of the screens during the installation. It may take a few seconds for all screens to appear.
Wireless Network Macintosh Install the Drivers & Software (Mac OS X 10.5.8 - 10.7.x) 22 a Before you install Make sure your machine is connected to the power and your Macintosh is ON. You must be logged on with Administrator rights. c d Note If you want to add the PS driver (BR-Script3 printer driver), please go to the Brother Solutions Center at http://solutions.brother.com/ and visit FAQ's on your model page for instructions. 23 a b Follow the on-screen instructions.
Wireless Network Note • You can find your machine’s MAC Address (Ethernet Address) and IP Address by printing out the Network Configuration Report. See Print the Network Configuration Report on page 41. • If this screen appears click OK. 1) Enter a name for your Macintosh in Display Name (up to 15 characters long). Macintosh 24 Download and install Presto! PageManager When Presto! PageManager is installed OCR capability is added to Brother ControlCenter2.
For Network Users Web Based Management (web browser) Print the Network Configuration Report The Brother print server is equipped with a web server that allows you to monitor its status or change some of its configuration settings, using HTTP (Hyper Text Transfer Protocol). You can print the Network Configuration Report to confirm the current network settings. Note We recommend Windows® Internet Explorer® 7.0/8.0 or Firefox® 3.6 for Windows® and Safari 4.0/5.0 for Macintosh.
Other Information Brother CreativeCenter Get inspired. If you're using Windows®, double-click the Brother CreativeCenter icon on your desktop to access our FREE web site with many ideas and resources for personal and professional use. Mac users can access Brother CreativeCenter at this web address: http://www.brother.
Options and Consumables Options The machine has the following optional accessories. You can expand the capabilities of the machine by adding these items. For more information about the optional Lower Tray Unit and compatible SO-DIMM Memory, visit us at http://solutions.brother.com/. For installing the SO-DIMM Memory, see Installing extra memory in the Advanced User's Guide. Lower Tray Unit LT-5400 The lower paper tray unit can hold up to 500 sheets of paper.
Trademarks The Brother logo is a registered trademark of Brother Industries, Ltd. Brother is a registered trademark of Brother Industries, Ltd. Microsoft, Windows, Windows Server and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. Apple, Macintosh, Safari and Mac OS are trademarks of Apple Inc.
