User Manual
Table Of Contents
- Network USER’S GUIDE
- Table of contents
- 1 Introduction
- 2 Configuring your network printer
- Overview
- IP addresses, subnet masks and gateways
- Setting the IP address and subnet mask
- Changing the print server settings
- 3 Configuring your machine for a wireless network
- Overview
- Confirm your network environment
- Wireless network terms and concepts
- Configuring your machine for a wireless network
- Changing the print server settings
- Using the BRAdmin Professional utility to change the wireless settings (for Windows® only)
- Using the control panel to configure your machine for a network
- Using other methods to configure your machine for a network
- Using a HTTP (web browser) to change the print server settings
- Using the Remote Setup to change the print server settings (for Windows® and Mac OS® X 10.2.4 or greater)
- 4 Wireless configuration for Windows®
- 5 Wireless configuration for Macintosh®
- 6 Control Panel Setup
- LAN Main Setup Menu
- Wired TCP/IP / WLAN TCP/IP
- Ethernet (Wired network only)
- Setup WLAN (Wireless network only)
- Set to default
- WLAN Status (Wireless network only)
- Wired Enable (Wired network only)
- Wireless Enable (Wireless network only)
- Setup I-Fax
- Setup Mail RX
- Setup Mail TX
- Setup Relay
- Scan to E-mail (E-mail server)
- Scan to FTP
- Fax to Server
- Time Zone
- Restoring the network settings to factory default
- Printing the Network Configuration List
- LAN Main Setup Menu
- 7 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 8 Internet printing for Windows®
- Overview
- Quick Tips
- Brother Internet Print General Information
- Brother Internet Print: Configuring the Brother Print Server
- Brother Internet Print: Using the BRAdmin Professional utility to Configure the Print Server
- Brother Internet Print: Using a Web Browser to Configure the Print Server
- Brother Internet Print: Installing the BIP software on Windows® 98/Me/2000/XP and Windows NT® 4.0
- Adding a Second Brother Internet Port
- Windows® 2000/XP IPP printing
- Specifying a different URL
- Other sources of information
- Overview
- 9 Network printing from a Macintosh®
- 10 Web Based Management
- 11 LDAP Operation
- 12 Internet FAX
- Overview
- Getting Connected
- Control Panel Key Functions
- Sending an Internet Fax
- Manually Entering Text
- Receiving E-mail or Internet Fax
- Receiving an Internet Fax to a PC
- Forwarding Received E-mail and Fax Messages
- Relay Broadcasting
- TX Verification Mail
- Setup Mail (TX)
- Setup Mail (RX)
- Error mail
- Important information on Internet Fax
- Overview
- 13 Troubleshooting
- Appendix A
- Using services
- Other ways to set the IP address (for advanced users and administrators)
- Using DHCP to configure the IP address
- Using BOOTP to configure the IP address
- Using RARP to configure the IP address
- Using APIPA to configure the IP address
- Using ARP to configure the IP address
- Using the TELNET console to configure the IP address
- Using the Brother Web BRAdmin server software for IIS* to configure the IP address
- Installation when using a Network Print Queue or Share (printer driver only)
- Appendix B
- Index
Troubleshooting
124
13
(2) Press the “Windows” key plus the “E” key to open My Computer.
(3) On the left, right click My Network Places, click Properties, then right click Local Area Connection
and click Properties.
(4) Click the Advanced tab. Under Internet Connection Firewall, verify that the box next to Protect
my computer... is unchecked. If the box is selected, click the box to remove the check. Then, click
OK.
(5) Once your firewall is disabled, try reinstalling the Brother software package. For instructions on how
to install from the CD-ROM, use the Quick Setup Guide we have provided with the machine.
(6) If the installation completed successfully, the Firewall on your computer was rejecting the necessary
network connection. In this case, you will need to disable the Firewall on your computer whenever
you install the network drivers.
Note
After the Brother software package is installed, enable again your Firewall. For instructions on how to
re-enable your Firewall software, refer to your User’s Guide or contact the Firewall software manufacturer.
For Macintosh
®
(for a wireless network)
Select again your machine in the DeviceSelector application located in Macintosh
HD/Library/Printers/Brother/Utilities or from the model pull-down list of the ControlCenter2.
7
Move your PC closer to the Brother machine and try again.
8
Reset the print server back to its default factory settings and try again. For the information how to reset
to the factory default settings, see Restoring the network settings to factory default on page 87.
Printing problems
Print job is not printed
Make sure the status and configuration of the print server. Check following:
1
Make sure that the machine is powered on, is on-line and ready to print.
2
Print the Network Configuration List of the machine and check if the settings such as IP address settings
are correct for your network. The problem may be the result of mismatched or duplicate IP address.
Verify that the IP address is correctly loaded into the print server. And make sure that no other nodes on
the network have this IP address.
3
Verify that the print server is on your network as follows: