User Manual
Table Of Contents
- Network USER’S GUIDE
- Table of contents
- 1 Introduction
- 2 Configuring your network printer
- Overview
- IP addresses, subnet masks and gateways
- Setting the IP address and subnet mask
- Changing the print server settings
- 3 Configuring your machine for a wireless network
- Overview
- Confirm your network environment
- Wireless network terms and concepts
- Configuring your machine for a wireless network
- Changing the print server settings
- Using the BRAdmin Professional utility to change the wireless settings (for Windows® only)
- Using the control panel to configure your machine for a network
- Using other methods to configure your machine for a network
- Using a HTTP (web browser) to change the print server settings
- Using the Remote Setup to change the print server settings (for Windows® and Mac OS® X 10.2.4 or greater)
- 4 Wireless configuration for Windows®
- 5 Wireless configuration for Macintosh®
- 6 Control Panel Setup
- LAN Main Setup Menu
- Wired TCP/IP / WLAN TCP/IP
- Ethernet (Wired network only)
- Setup WLAN (Wireless network only)
- Set to default
- WLAN Status (Wireless network only)
- Wired Enable (Wired network only)
- Wireless Enable (Wireless network only)
- Setup I-Fax
- Setup Mail RX
- Setup Mail TX
- Setup Relay
- Scan to E-mail (E-mail server)
- Scan to FTP
- Fax to Server
- Time Zone
- Restoring the network settings to factory default
- Printing the Network Configuration List
- LAN Main Setup Menu
- 7 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 8 Internet printing for Windows®
- Overview
- Quick Tips
- Brother Internet Print General Information
- Brother Internet Print: Configuring the Brother Print Server
- Brother Internet Print: Using the BRAdmin Professional utility to Configure the Print Server
- Brother Internet Print: Using a Web Browser to Configure the Print Server
- Brother Internet Print: Installing the BIP software on Windows® 98/Me/2000/XP and Windows NT® 4.0
- Adding a Second Brother Internet Port
- Windows® 2000/XP IPP printing
- Specifying a different URL
- Other sources of information
- Overview
- 9 Network printing from a Macintosh®
- 10 Web Based Management
- 11 LDAP Operation
- 12 Internet FAX
- Overview
- Getting Connected
- Control Panel Key Functions
- Sending an Internet Fax
- Manually Entering Text
- Receiving E-mail or Internet Fax
- Receiving an Internet Fax to a PC
- Forwarding Received E-mail and Fax Messages
- Relay Broadcasting
- TX Verification Mail
- Setup Mail (TX)
- Setup Mail (RX)
- Error mail
- Important information on Internet Fax
- Overview
- 13 Troubleshooting
- Appendix A
- Using services
- Other ways to set the IP address (for advanced users and administrators)
- Using DHCP to configure the IP address
- Using BOOTP to configure the IP address
- Using RARP to configure the IP address
- Using APIPA to configure the IP address
- Using ARP to configure the IP address
- Using the TELNET console to configure the IP address
- Using the Brother Web BRAdmin server software for IIS* to configure the IP address
- Installation when using a Network Print Queue or Share (printer driver only)
- Appendix B
- Index
Control Panel Setup
72
6
DNS Server
1
(For Wired) Press Menu, 6, 1, 1, 8.
(For Wireless) Press Menu, 6, 2, 1, 8.
2
Press ▲ or ▼ to select Primary or Secondary.
3
Press OK.
4
Enter the DNS Server address.
5
Press OK.
6
Press Stop/Exit.
Primary DNS Server IP Address
This field specifies the IP address of the primary DNS (Domain Name Service) server.
Secondary DNS Server IP Address
This field specifies the IP address of the secondary DNS server. It is used as a backup to the Primary DNS
server address. If the Primary server is unavailable, the machine will contact the Secondary DNS server.
APIPA
When enabled, the print server will automatically allocate a IP address in the range (169.254.1.0 -
169.254.254.255) when the print server cannot obtain an IP address through the BOOT Method you have set
(Menu, 6, 1, 1, 1 ). Selecting Off means the IP address doesn’t change, when the print server cannot obtain
an IP address through the BOOT Method you have set.
1
(For Wired) Press Menu, 6, 1, 1, 9.
(For Wireless) Press Menu, 6, 2, 1, 9.
2
Press ▲ or ▼ to select On or Off.
3
Press OK.
4
Press Stop/Exit.