User Manual
Table Of Contents
- Network USER’S GUIDE
- Table of contents
- 1 Introduction
- 2 Configuring your network printer
- Overview
- IP addresses, subnet masks and gateways
- Setting the IP address and subnet mask
- Changing the print server settings
- 3 Configuring your machine for a wireless network
- Overview
- Confirm your network environment
- Wireless network terms and concepts
- Configuring your machine for a wireless network
- Changing the print server settings
- Using the BRAdmin Professional utility to change the wireless settings (for Windows® only)
- Using the control panel to configure your machine for a network
- Using other methods to configure your machine for a network
- Using a HTTP (web browser) to change the print server settings
- Using the Remote Setup to change the print server settings (for Windows® and Mac OS® X 10.2.4 or greater)
- 4 Wireless configuration for Windows®
- 5 Wireless configuration for Macintosh®
- 6 Control Panel Setup
- LAN Main Setup Menu
- Wired TCP/IP / WLAN TCP/IP
- Ethernet (Wired network only)
- Setup WLAN (Wireless network only)
- Set to default
- WLAN Status (Wireless network only)
- Wired Enable (Wired network only)
- Wireless Enable (Wireless network only)
- Setup I-Fax
- Setup Mail RX
- Setup Mail TX
- Setup Relay
- Scan to E-mail (E-mail server)
- Scan to FTP
- Fax to Server
- Time Zone
- Restoring the network settings to factory default
- Printing the Network Configuration List
- LAN Main Setup Menu
- 7 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 8 Internet printing for Windows®
- Overview
- Quick Tips
- Brother Internet Print General Information
- Brother Internet Print: Configuring the Brother Print Server
- Brother Internet Print: Using the BRAdmin Professional utility to Configure the Print Server
- Brother Internet Print: Using a Web Browser to Configure the Print Server
- Brother Internet Print: Installing the BIP software on Windows® 98/Me/2000/XP and Windows NT® 4.0
- Adding a Second Brother Internet Port
- Windows® 2000/XP IPP printing
- Specifying a different URL
- Other sources of information
- Overview
- 9 Network printing from a Macintosh®
- 10 Web Based Management
- 11 LDAP Operation
- 12 Internet FAX
- Overview
- Getting Connected
- Control Panel Key Functions
- Sending an Internet Fax
- Manually Entering Text
- Receiving E-mail or Internet Fax
- Receiving an Internet Fax to a PC
- Forwarding Received E-mail and Fax Messages
- Relay Broadcasting
- TX Verification Mail
- Setup Mail (TX)
- Setup Mail (RX)
- Error mail
- Important information on Internet Fax
- Overview
- 13 Troubleshooting
- Appendix A
- Using services
- Other ways to set the IP address (for advanced users and administrators)
- Using DHCP to configure the IP address
- Using BOOTP to configure the IP address
- Using RARP to configure the IP address
- Using APIPA to configure the IP address
- Using ARP to configure the IP address
- Using the TELNET console to configure the IP address
- Using the Brother Web BRAdmin server software for IIS* to configure the IP address
- Installation when using a Network Print Queue or Share (printer driver only)
- Appendix B
- Index
Control Panel Setup
81
6
Size Limit
Some E-mail servers do not allow you to send large E-mail documents. (the System Administrator will often
place a limit on the maximum E-mail size). With this function enabled, the machine will display Out of
Memory when trying to send E-mail documents over 1Mbyte in size. The document will not be sent and an
error report will be printed. The document you are sending should be separated into smaller documents that
will be accepted by the mail server. (For your information, a 42 page document based on the ITU-T Test
Chart#1 test chart is approximately 1Mbyte in size).
1
Press Menu, 6, 3, 3, 2.
2
Press ▲ or ▼ to select On or Off.
3
Press OK.
4
Press Stop/Exit.
Notification
The notification feature allows a confirmation of receipt message to be transmitted to the sending station
When the I-Fax has been received.
This feature only works on I-Fax machines that support the “MDN” specification.
1
Press Menu, 6, 3, 3, 3.
2
Press ▲ or ▼ to select On or Off.
3
Press OK.
4
Press Stop/Exit.