User Manual
Table Of Contents
- Network USER’S GUIDE
- Table of contents
- 1 Introduction
- 2 Configuring your network printer
- Overview
- IP addresses, subnet masks and gateways
- Setting the IP address and subnet mask
- Changing the print server settings
- 3 Configuring your machine for a wireless network
- Overview
- Confirm your network environment
- Wireless network terms and concepts
- Configuring your machine for a wireless network
- Changing the print server settings
- Using the BRAdmin Professional utility to change the wireless settings (for Windows® only)
- Using the control panel to configure your machine for a network
- Using other methods to configure your machine for a network
- Using a HTTP (web browser) to change the print server settings
- Using the Remote Setup to change the print server settings (for Windows® and Mac OS® X 10.2.4 or greater)
- 4 Wireless configuration for Windows®
- 5 Wireless configuration for Macintosh®
- 6 Control Panel Setup
- LAN Main Setup Menu
- Wired TCP/IP / WLAN TCP/IP
- Ethernet (Wired network only)
- Setup WLAN (Wireless network only)
- Set to default
- WLAN Status (Wireless network only)
- Wired Enable (Wired network only)
- Wireless Enable (Wireless network only)
- Setup I-Fax
- Setup Mail RX
- Setup Mail TX
- Setup Relay
- Scan to E-mail (E-mail server)
- Scan to FTP
- Fax to Server
- Time Zone
- Restoring the network settings to factory default
- Printing the Network Configuration List
- LAN Main Setup Menu
- 7 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 8 Internet printing for Windows®
- Overview
- Quick Tips
- Brother Internet Print General Information
- Brother Internet Print: Configuring the Brother Print Server
- Brother Internet Print: Using the BRAdmin Professional utility to Configure the Print Server
- Brother Internet Print: Using a Web Browser to Configure the Print Server
- Brother Internet Print: Installing the BIP software on Windows® 98/Me/2000/XP and Windows NT® 4.0
- Adding a Second Brother Internet Port
- Windows® 2000/XP IPP printing
- Specifying a different URL
- Other sources of information
- Overview
- 9 Network printing from a Macintosh®
- 10 Web Based Management
- 11 LDAP Operation
- 12 Internet FAX
- Overview
- Getting Connected
- Control Panel Key Functions
- Sending an Internet Fax
- Manually Entering Text
- Receiving E-mail or Internet Fax
- Receiving an Internet Fax to a PC
- Forwarding Received E-mail and Fax Messages
- Relay Broadcasting
- TX Verification Mail
- Setup Mail (TX)
- Setup Mail (RX)
- Error mail
- Important information on Internet Fax
- Overview
- 13 Brother Internet Fax Printing Software
- 14 Troubleshooting
- Appendix A
- Using services
- Other ways to set the IP address (for advanced users and administrators)
- Using DHCP to configure the IP address
- Using BOOTP to configure the IP address
- Using RARP to configure the IP address
- Using APIPA to configure the IP address
- Using ARP to configure the IP address
- Using the TELNET console to configure the IP address
- Using the Brother Web BRAdmin server software for IIS* to configure the IP address
- Installation when using a Network Print Queue or Share (printer driver only)
- Appendix B
- Index
Brother Internet Fax Printing Software
121
13
Installing Brother Internet Fax Printing Driver
Insert the CD-ROM supplied with your Brother machine into your CD-ROM Drive. The installer screen will
automatically start.
Note
If the installer screen does not appear automatically, select Start/Run and type X:/setup.exe.
(X:/ should be the drive letter of your CD-ROM drive on your PC)
1
Select Install Other Drivers or Utilities.
2
Select Brother Internet Fax Printing (BFP) Driver.
3
Click Install.
Next you will be presented with the licensing agreement, please carefully read the agreement and make the
necessary choice.
During the installation you are
presented with the following screen,
select the default unless you have
previously installed this software. If this
is the case use a port number that has
not been previously configured.
Example BFP2
You also need to enter certain
information into the printer driver dialog
screen.
It is very important that you enter your
own E-mail address. You also need to
configure the SMTP mail server IP
address or Node Name.
Note
If in any doubt contact your Network Administrator for assistance.
When Installing BFP on Windows
®
2000/XP and Windows NT
®
4.0
operating systems we recommend
that you add a “:” to the end of the
port name.
This can be the Node
Name or IP address of
the E-mail server
Here you can enter the default E-mail
address of the print server or you can
leave it blank.
* If an address is specified here this
will always be used as default