User Manual
Table Of Contents
- Network USER’S GUIDE
- Table of contents
- 1 Introduction
- 2 Configuring your network printer
- Overview
- IP addresses, subnet masks and gateways
- Setting the IP address and subnet mask
- Changing the print server settings
- 3 Configuring your machine for a wireless network
- Overview
- Confirm your network environment
- Wireless network terms and concepts
- Configuring your machine for a wireless network
- Changing the print server settings
- Using the BRAdmin Professional utility to change the wireless settings (for Windows® only)
- Using the control panel to configure your machine for a network
- Using other methods to configure your machine for a network
- Using a HTTP (web browser) to change the print server settings
- Using the Remote Setup to change the print server settings (for Windows® and Mac OS® X 10.2.4 or greater)
- 4 Wireless configuration for Windows®
- 5 Wireless configuration for Macintosh®
- 6 Control Panel Setup
- LAN Main Setup Menu
- Wired TCP/IP / WLAN TCP/IP
- Ethernet (Wired network only)
- Setup WLAN (Wireless network only)
- Set to default
- WLAN Status (Wireless network only)
- Wired Enable (Wired network only)
- Wireless Enable (Wireless network only)
- Setup I-Fax
- Setup Mail RX
- Setup Mail TX
- Setup Relay
- Scan to E-mail (E-mail server)
- Scan to FTP
- Fax to Server
- Time Zone
- Restoring the network settings to factory default
- Printing the Network Configuration List
- LAN Main Setup Menu
- 7 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 8 Internet printing for Windows®
- Overview
- Quick Tips
- Brother Internet Print General Information
- Brother Internet Print: Configuring the Brother Print Server
- Brother Internet Print: Using the BRAdmin Professional utility to Configure the Print Server
- Brother Internet Print: Using a Web Browser to Configure the Print Server
- Brother Internet Print: Installing the BIP software on Windows® 98/Me/2000/XP and Windows NT® 4.0
- Adding a Second Brother Internet Port
- Windows® 2000/XP IPP printing
- Specifying a different URL
- Other sources of information
- Overview
- 9 Network printing from a Macintosh®
- 10 Web Based Management
- 11 LDAP Operation
- 12 Internet FAX
- Overview
- Getting Connected
- Control Panel Key Functions
- Sending an Internet Fax
- Manually Entering Text
- Receiving E-mail or Internet Fax
- Receiving an Internet Fax to a PC
- Forwarding Received E-mail and Fax Messages
- Relay Broadcasting
- TX Verification Mail
- Setup Mail (TX)
- Setup Mail (RX)
- Error mail
- Important information on Internet Fax
- Overview
- 13 Brother Internet Fax Printing Software
- 14 Troubleshooting
- Appendix A
- Using services
- Other ways to set the IP address (for advanced users and administrators)
- Using DHCP to configure the IP address
- Using BOOTP to configure the IP address
- Using RARP to configure the IP address
- Using APIPA to configure the IP address
- Using ARP to configure the IP address
- Using the TELNET console to configure the IP address
- Using the Brother Web BRAdmin server software for IIS* to configure the IP address
- Installation when using a Network Print Queue or Share (printer driver only)
- Appendix B
- Index
Appendix A
144
A
Note
You must be on the same Ethernet segment (that is, there cannot be a router between the print server and
operating system) to use the arp -s command.
If there is a router, you may use BOOTP or other methods described in this chapter to enter the IP address.
If your Administrator has configured the system to deliver IP addresses using BOOTP, DHCP or RARP your
Brother print server can receive an IP address from any one of these IP address allocation systems. In which
case, you will not need to use the ARP command. The ARP command only works once. For security reasons,
once you have successfully configured the IP address of a Brother print server using the ARP command, you
cannot use the ARP command again to change the address. The print server will ignore any attempts to do
this. If you wish to change the IP address again, use a web browser, TELNET (using the SET IP ADDRESS
command) or factory reset the print server (which will then allow you to use the ARP command again).
To configure the print server and to verify the connection, enter the following command ping ipaddress
where ipaddress is the IP address of the print server. For example, ping 192.189.207.2.
Using the TELNET console to configure the IP address
You can also use the TELNET command to change the IP address.
TELNET is an effective method to change the machine’s IP address. But a valid IP address must already be
programmed into print server.
Type TELNET ipaddress at the command prompt of the system prompt, where ipaddress is the IP address
of the print server. When you are connected, push the Return or Enter key to get the “#” prompt.
You will be prompted for a user name. Enter anything in response to this prompt.
You will then get the Local> prompt. Type SET IP ADDRESS ipaddress, where ipaddress is the
desired IP address you wish to assign to the print server (check with your network administrator for the IP
address to use). For example:
Local> SET IP ADDRESS 192.168.1.3
You will now need to set the subnet mask by typing SET IP SUBNET subnet mask, where subnet mask
is the desired subnet mask you wish to assign to the print server (check with your network administrator for
the subnet mask to use). For example:
Local> SET IP SUBNET 255.255.255.0
If you do not have any subnets, use one of the following default subnet masks:
255.0.0.0 for class A networks
255.255.0.0 for class B networks
255.255.255.0 for class C networks