Network User's Guide
Table Of Contents
- Network User’s Guide
- Applicable models
- Definitions of notes
- IMPORTANT NOTE
- Table of Contents
- Section I: Network Operation
- 1 Introduction
- 2 Changing your machine’s network settings
- 3 Configuring your machine for a wireless network (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- Overview
- Confirm your network environment
- Wireless configuration temporarily using a USB cable (Recommended)
- Configuration using the machine’s control panel Setup Wizard
- One push configuration using WPS (Wi-Fi Protected Setup) or AOSS™
- Configuration using the PIN Method of WPS (Wi-Fi Protected Setup)
- Configuration in Ad-hoc mode
- 4 Control panel setup
- Network menu
- TCP/IP
- Ethernet (wired network only)
- Wired Status (For HL-3180CDW, DCP-9015CDW, DCP-9020CDN, DCP-9020CDW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW)
- Setup Wizard (wireless network only)
- WPS (Wi-Fi Protected Setup)/AOSS™ (wireless network only)
- WPS (Wi-Fi Protected Setup) w/PIN Code (wireless network only)
- WLAN Status (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- MAC Address
- Set to Default
- Wired Enable (For DCP-9020CDW, MFC-9330CDW and MFC-9340CDW)
- WLAN Enable
- E-mail / IFAX (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- Fax to Server (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- How to set a new default for Scan to FTP
- How to set a new default for Scan to Network (Windows®)
- Reset the network settings to the factory default
- Printing the Network Configuration Report
- Printing the WLAN report (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- Function table and default factory settings
- Network menu
- 5 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Setting a password
- Secure Function Lock 2.0
- Synchronize with SNTP server
- Store Print Log to Network
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser (Windows®)
- 6 Internet fax (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- 7 Security features
- Overview
- Using Certificates for device security
- Managing multiple certificates
- Managing your network machine securely using SSL/TLS
- Secure Management using BRAdmin Professional 3 (Windows®)
- Printing documents securely using SSL/TLS
- Sending or Receiving an E-mail securely
- Using IEEE 802.1x authentication
- 8 Troubleshooting
- Section II: Network Glossary
- 9 Types of network connections and protocols
- 10 Configuring your machine for a network
- 11 Wireless network terms and concepts (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- 12 Additional network settings from Windows®
- Types of additional network settings
- Installing drivers used for printing and scanning via Web Services (Windows Vista®, Windows® 7 and Windows® 8)
- Uninstalling drivers used for printing and scanning via Web Services (Windows Vista®, Windows® 7 and Windows® 8)
- Network printing and scanning installation for Infrastructure mode when using Vertical Pairing (Windows® 7 and Windows® 8)
- 13 Security terms and concepts
- Section III: Appendixes
- Index
Troubleshooting
112
8
I want to check my network devices are working properly.
Question Interface Solution
Is your Brother machine,
access point/router, or
network hub turned on?
wired/
wireless
Make sure you have confirmed all instructions in First check the following:
on page 105.
Where can I find my Brother
machine's network settings,
such as IP address?
wired/
wireless
Print the Network Configuration Report. (See Printing the Network
Configuration Report on page 48.)
How can I check the link
status of my Brother
machine?
wired/
wireless
Print the Network Configuration Report and check that Ethernet Link
Status or Wireless Link Status is Link OK. (See Printing the Network
Configuration Report on page 48.)
If the report shows Link DOWN or Failed To Associate, start over again
from the First check the following: on page 105.
Can I “ping” the Brother
machine from my
computer?
wired/
wireless
Ping the Brother machine from your computer using the IP address or the
node name.
Successful i Your Brother machine is working correctly and connected
to the same network as your computer.
Unsuccessful i Your Brother machine is not connected to the same
network as your computer.
(Windows
®
)
Ask the network administrator and use the Network Connection Repair
Tool to fix the IP address and the subnet mask automatically. For the
detail of the Network Connection Repair Tool, see (Windows
®
) Confirm
the IP address and the Subnet Mask using the Network Connection
Repair Tool. in Is your Brother machine assigned with an available IP
address? on page 108.
Is the Brother machine
connecting to the wireless
network?
wireless Print the WLAN report to confirm the state of the wireless connection. For
how to print, see Printing the WLAN report (For HL-3180CDW,
DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and
MFC-9340CDW) on page 48. If there is an error code on the printed
WLAN report: see Quick Setup Guide: Troubleshooting.
I have checked and tried all
of the above, however, I'm
still having problems. Is
there anything else I can
do?
wireless See the instructions supplied with your WLAN access point/router to find the
SSID and the Network Key information and set them correctly. For details of
the SSID and the Network Key, See Are your security settings
(SSID/Network Key) correct? in I cannot complete the wireless network
setup configuration. on page 106.