Network User's Guide
Table Of Contents
- Network User’s Guide
- Applicable models
- Definitions of notes
- IMPORTANT NOTE
- Table of Contents
- Section I: Network Operation
- 1 Introduction
- 2 Changing your machine’s network settings
- 3 Configuring your machine for a wireless network (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- Overview
- Confirm your network environment
- Wireless configuration temporarily using a USB cable (Recommended)
- Configuration using the machine’s control panel Setup Wizard
- One push configuration using WPS (Wi-Fi Protected Setup) or AOSS™
- Configuration using the PIN Method of WPS (Wi-Fi Protected Setup)
- Configuration in Ad-hoc mode
- 4 Control panel setup
- Network menu
- TCP/IP
- Ethernet (wired network only)
- Wired Status (For HL-3180CDW, DCP-9015CDW, DCP-9020CDN, DCP-9020CDW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW)
- Setup Wizard (wireless network only)
- WPS (Wi-Fi Protected Setup)/AOSS™ (wireless network only)
- WPS (Wi-Fi Protected Setup) w/PIN Code (wireless network only)
- WLAN Status (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- MAC Address
- Set to Default
- Wired Enable (For DCP-9020CDW, MFC-9330CDW and MFC-9340CDW)
- WLAN Enable
- E-mail / IFAX (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- Fax to Server (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- How to set a new default for Scan to FTP
- How to set a new default for Scan to Network (Windows®)
- Reset the network settings to the factory default
- Printing the Network Configuration Report
- Printing the WLAN report (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- Function table and default factory settings
- Network menu
- 5 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Setting a password
- Secure Function Lock 2.0
- Synchronize with SNTP server
- Store Print Log to Network
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser (Windows®)
- 6 Internet fax (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- 7 Security features
- Overview
- Using Certificates for device security
- Managing multiple certificates
- Managing your network machine securely using SSL/TLS
- Secure Management using BRAdmin Professional 3 (Windows®)
- Printing documents securely using SSL/TLS
- Sending or Receiving an E-mail securely
- Using IEEE 802.1x authentication
- 8 Troubleshooting
- Section II: Network Glossary
- 9 Types of network connections and protocols
- 10 Configuring your machine for a network
- 11 Wireless network terms and concepts (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- 12 Additional network settings from Windows®
- Types of additional network settings
- Installing drivers used for printing and scanning via Web Services (Windows Vista®, Windows® 7 and Windows® 8)
- Uninstalling drivers used for printing and scanning via Web Services (Windows Vista®, Windows® 7 and Windows® 8)
- Network printing and scanning installation for Infrastructure mode when using Vertical Pairing (Windows® 7 and Windows® 8)
- 13 Security terms and concepts
- Section III: Appendixes
- Index
Configuring your machine for a wireless network (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW,
MFC-9330CDW and MFC-9340CDW)
24
3
NOTE
• If you configure your machine using EAP-TLS Authentication, you must install the Client Certificate issued
by a CA before you start configuration. Contact your network administrator about the Client Certificate. If
you have installed more than one certificate, we recommend you write down the certificate name you want
to use. For installing the certificate, see Using Certificates for device security on page 84.
• If you verify your machine using the Common Name of the Server Certificate, we recommend you write
down the Common Name before you start configuration. Contact your network administrator about the
Common Name of the Server Certificate.
b Press .
c Press Network.
d Press WLAN.
e Swipe up or down, or press a or b to display Setup Wizard.
Press Setup Wizard.
f When Enable WLAN? is displayed, press Yes to accept.
This will start the wireless setup wizard.
To cancel, press No.
g The machine will search for your network and display a list of available SSIDs.
You should see the SSID you wrote down earlier. If the machine finds more than one network, swipe up
or down, or press a or b to choose your network. Go to step k. Press OK.
If your access point is set to not broadcast the SSID, you will have to add the SSID name manually. Go
to step h.
h Swipe up or down, or press a or b to choose <New SSID>. Press OK.
Go to step i.
i Enter the SSID name. (For information on how to enter text: see Quick Setup Guide.)
Press OK. Go to step j.
j Choose Infrastructure when instructed.
k Choose the Authentication method using a or b.
Do one of the following:
If you chose LEAP, go to step q.
If you chose EAP-FAST, go to step l.
If you chose PEAP, go to step l.
If you chose EAP-TTLS, go to step l.
If you chose EAP-TLS, go to step m.