Network User's Guide
Table Of Contents
- Network User’s Guide
- Applicable models
- Definitions of notes
- IMPORTANT NOTE
- Table of Contents
- Section I: Network Operation
- 1 Introduction
- 2 Changing your machine’s network settings
- 3 Configuring your machine for a wireless network (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- Overview
- Confirm your network environment
- Wireless configuration temporarily using a USB cable (Recommended)
- Configuration using the machine’s control panel Setup Wizard
- One push configuration using WPS (Wi-Fi Protected Setup) or AOSS™
- Configuration using the PIN Method of WPS (Wi-Fi Protected Setup)
- Configuration in Ad-hoc mode
- 4 Control panel setup
- Network menu
- TCP/IP
- Ethernet (wired network only)
- Wired Status (For HL-3180CDW, DCP-9015CDW, DCP-9020CDN, DCP-9020CDW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW)
- Setup Wizard (wireless network only)
- WPS (Wi-Fi Protected Setup)/AOSS™ (wireless network only)
- WPS (Wi-Fi Protected Setup) w/PIN Code (wireless network only)
- WLAN Status (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- MAC Address
- Set to Default
- Wired Enable (For DCP-9020CDW, MFC-9330CDW and MFC-9340CDW)
- WLAN Enable
- E-mail / IFAX (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- Fax to Server (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- How to set a new default for Scan to FTP
- How to set a new default for Scan to Network (Windows®)
- Reset the network settings to the factory default
- Printing the Network Configuration Report
- Printing the WLAN report (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- Function table and default factory settings
- Network menu
- 5 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Setting a password
- Secure Function Lock 2.0
- Synchronize with SNTP server
- Store Print Log to Network
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser (Windows®)
- 6 Internet fax (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- 7 Security features
- Overview
- Using Certificates for device security
- Managing multiple certificates
- Managing your network machine securely using SSL/TLS
- Secure Management using BRAdmin Professional 3 (Windows®)
- Printing documents securely using SSL/TLS
- Sending or Receiving an E-mail securely
- Using IEEE 802.1x authentication
- 8 Troubleshooting
- Section II: Network Glossary
- 9 Types of network connections and protocols
- 10 Configuring your machine for a network
- 11 Wireless network terms and concepts (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- 12 Additional network settings from Windows®
- Types of additional network settings
- Installing drivers used for printing and scanning via Web Services (Windows Vista®, Windows® 7 and Windows® 8)
- Uninstalling drivers used for printing and scanning via Web Services (Windows Vista®, Windows® 7 and Windows® 8)
- Network printing and scanning installation for Infrastructure mode when using Vertical Pairing (Windows® 7 and Windows® 8)
- 13 Security terms and concepts
- Section III: Appendixes
- Index
Control panel setup
42
4
Verify Cert.
You can enable or disable the use of the security certificate between the machine and the POP3 server.
APOP
You can enable or disable the APOP (Authenticated Post Office Protocol).
Setup Mail RX 4
Auto Polling
When set to On, the machine automatically checks the POP3 server for new messages.
4
Poll Frequency
Sets the interval for checking for new messages on the POP3 server (default is 10 minutes).
4
Header
This selection allows the contents of the mail header to be printed when the received message is printed.
4
Delete Error Mail
When set to On, the machine automatically deletes error mails that the machine cannot receive from the
POP3 server.
4
Notification
The notification feature allows a confirmation of receipt message to be transmitted to the sending station
when the Internet Fax has been received.
This feature only works on Internet Fax machines that support the “MDN” specification.
Setup Mail TX 4
Sender Subject
This field displays the subject that is attached to the Internet fax data being sent from the Brother machine to
a computer (default is “Internet Fax Job”).










