Network User's Guide
Table Of Contents
- Network User’s Guide
- Applicable models
- Definitions of notes
- IMPORTANT NOTE
- Table of Contents
- Section I: Network Operation
- 1 Introduction
- 2 Changing your machine’s network settings
- 3 Configuring your machine for a wireless network (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- Overview
- Confirm your network environment
- Wireless configuration temporarily using a USB cable (Recommended)
- Configuration using the machine’s control panel Setup Wizard
- One push configuration using WPS (Wi-Fi Protected Setup) or AOSS™
- Configuration using the PIN Method of WPS (Wi-Fi Protected Setup)
- Configuration in Ad-hoc mode
- 4 Control panel setup
- Network menu
- TCP/IP
- Ethernet (wired network only)
- Wired Status (For HL-3180CDW, DCP-9015CDW, DCP-9020CDN, DCP-9020CDW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW)
- Setup Wizard (wireless network only)
- WPS (Wi-Fi Protected Setup)/AOSS™ (wireless network only)
- WPS (Wi-Fi Protected Setup) w/PIN Code (wireless network only)
- WLAN Status (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- MAC Address
- Set to Default
- Wired Enable (For DCP-9020CDW, MFC-9330CDW and MFC-9340CDW)
- WLAN Enable
- E-mail / IFAX (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- Fax to Server (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- How to set a new default for Scan to FTP
- How to set a new default for Scan to Network (Windows®)
- Reset the network settings to the factory default
- Printing the Network Configuration Report
- Printing the WLAN report (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- Function table and default factory settings
- Network menu
- 5 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Setting a password
- Secure Function Lock 2.0
- Synchronize with SNTP server
- Store Print Log to Network
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser (Windows®)
- 6 Internet fax (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
- 7 Security features
- Overview
- Using Certificates for device security
- Managing multiple certificates
- Managing your network machine securely using SSL/TLS
- Secure Management using BRAdmin Professional 3 (Windows®)
- Printing documents securely using SSL/TLS
- Sending or Receiving an E-mail securely
- Using IEEE 802.1x authentication
- 8 Troubleshooting
- Section II: Network Glossary
- 9 Types of network connections and protocols
- 10 Configuring your machine for a network
- 11 Wireless network terms and concepts (For HL-3180CDW, DCP-9015CDW, DCP-9020CDW, MFC-9130CW, MFC-9330CDW and MFC-9340CDW)
- 12 Additional network settings from Windows®
- Types of additional network settings
- Installing drivers used for printing and scanning via Web Services (Windows Vista®, Windows® 7 and Windows® 8)
- Uninstalling drivers used for printing and scanning via Web Services (Windows Vista®, Windows® 7 and Windows® 8)
- Network printing and scanning installation for Infrastructure mode when using Vertical Pairing (Windows® 7 and Windows® 8)
- 13 Security terms and concepts
- Section III: Appendixes
- Index
Internet fax (MFC-9130CW, MFC-9140CDN, MFC-9330CDW and MFC-9340CDW: available as a download)
82
6
NOTE
To receive the TX verification mail properly, you must configure the following settings.
• Sender
• Switch Notification in the Setup Mail TX to on.
• Switch Header in the Setup Mail RX to All or Subject+From+To.
• Receiver
• Switch Notification in the Setup Mail RX to on.
Error mail 6
If there is a mail delivery error while sending an Internet fax, the mail server will send an error message back
to the machine and the error message will be printed. If there is an error while receiving mail, an error
message will be printed (Example: “The message being sent to the machine was not in a TIFF-F format.”).
To receive the error mail properly, you must switch Header in the Setup Mail RX to All or Subject+From+To.