Network User's Guide
Table Of Contents
- NETWORK USER’S GUIDE
- Definitions of warnings, cautions, and notes
- Compilation and publication notice
- IMPORTANT NOTE
- Brother numbers
- Table of Contents
- 1 Introduction
- 2 Configuring your machine for a network with an Ethernet cable connection (DCP-J715W, MFC-J615W and MFC-J630W only)
- Overview
- IP addresses, subnet masks and gateways
- Step by step chart
- Setting up the IP address and subnet mask
- Changing the print server settings
- Using the BRAdmin Light utility to change the print server settings
- Using the BRAdmin Professional 3 utility to change the wireless settings (Windows®)
- Using the Remote Setup to change the print server settings (MFC-J615W and MFC-J630W only) (Not available for Windows Server® 2003/2008)
- Using the control panel to change the print server settings
- 3 Configuring your machine for a wireless network
- Overview
- Wireless network terms and concepts
- Step by step chart for wireless network configuration
- Confirm your network environment
- Confirm your wireless network setup method
- Configuration using the machine’s control panel Setup Wizard to configure your wireless network machine
- Configuration using the WPS/AOSS™ control panel menu (Infrastructure mode only)
- Configuration using the PIN Method of Wi-Fi Protected Setup (Infrastructure mode only)
- Configuration using the Brother installer application on the installation CD-ROM to configure your wireless network machine
- Configuring your machine for a wireless network
- Using the Setup Wizard from the control panel
- Using WPS or AOSS™ from the control panel menu to configure your machine for a wireless network
- Using the PIN Method of Wi-Fi Protected Setup
- Using the Brother automatic installer application on the installation CD-ROM to configure your machine for a wireless network
- 4 Wireless configuration using the Brother installer application
- 5 Control panel setup
- Network menu
- Restoring the network settings to factory default
- Printing the Network Configuration List
- Printing the WLAN Report
- 6 Driver Deployment Wizard (Windows® only)
- 7 Network printing from Windows® basic TCP/IP Peer-to-Peer printing
- 8 Network printing from a Macintosh
- 9 Troubleshooting
- Appendix A
- Appendix B
- Index
65
5
5
Network menu 5
Before using your Brother product in a network environment, you need to configure the correct TCP/IP
settings.
In this chapter, you will learn how to configure the network settings using the control panel, located on the
front of the machine.
The Network menu selections of the control panel allow you to set up the Brother machine for your network
configuration. Press Menu, then press a or b to choose Network. Proceed to the menu selection you wish
to configure. (See Function table and default factory settings on page 109.)
Please note that the machine is supplied with the BRAdmin Light software and Remote Setup applications
for Windows
®
and Macintosh, which also can be used to configure many aspects of the network. (See
Configuring your machine for a network with an Ethernet cable connection (DCP-J715W, MFC-J615W and
MFC-J630W only) on page 9 for a wired connection or Changing the print server settings on page 15 for a
wireless connection.)
TCP/IP 5
If you connect the machine with an Ethernet cable to your network, use the Wired LAN menu selections. If
you connect the machine to a wireless Ethernet network, use the WLAN menu selections. (DCP-J715W,
MFC-J615W and MFC-J630W only)
This menu has 9 sections: BOOT Method, IP Address, Subnet Mask, Gateway, Node Name,
WINS Config, WINS Server, DNS Server and APIPA.
BOOT Method 5
This selection controls how the machine obtains an IP address. The default setting is Auto.
Note
If you do not want your print server configured via DHCP, BOOTP or RARP, you must set the
BOOT Method to Static so that the print server has a static IP address. This will prevent the print server
from trying to obtain an IP address from any of these systems. To change the BOOT Method, use the
machine’s control panel, BRAdmin Light utility or Remote Setup.
a Press Menu.
b Press a or b to choose Network.
Press OK.
c For DCP-J715W, MFC-J615W and MFC-J630W
(For Wired) Press a or b to choose Wired LAN, and press OK.
(For Wireless) Press a or b to choose WLAN, and press OK.
d Press a or b to choose TCP/IP.
Press OK.
Control panel setup 5