User Manual
Table Of Contents
- Quick Setup Guide MFC-J5910DW
- Start Here
- 1 Unpack the machine and check the components
- 2 Load plain A4 paper
- 3 Connect the power cord and telephone line
- 4 Set your country (Australia and New Zealand only)
- 5 Install the ink cartridges
- 6 Check the print quality
- 7 Choose your language (if needed) (Not available in Australia and New Zealand)
- 8 Choose a Receive Mode
- 9 Set the LCD contrast (if needed)
- 10 Set the date and time
- 11 Enter personal information (Station ID)
- 12 Fax Transmission Report
- 13 Set Tone or Pulse dialling mode (Not available in New Zealand)
- 14 Set the telephone line compatibility (VoIP)
- 15 Choose your connection type
- For USB interface users (Windows® XP Home/XP Professional/Windows Vista®/Windows® 7)
- For USB interface users (Mac OS X 10.4.11, 10.5.x, 10.6.x)
- For wired network interface users (Windows® XP Home/XP Professional/Windows Vista®/Windows® 7)
- For wired network interface users (Mac OS X 10.4.11, 10.5.x, 10.6.x)
- For wireless network interface users
- 16 Before you begin
- 17 Choose your wireless install method
- 18 Configuration using the CD-ROM installer and a USB cable (Windows® only)
- 18 Manual configuration from the control panel (Windows® and Macintosh)
- 18 One-push configuration using WPS or AOSS™ (Windows® and Macintosh)
- Troubleshooting
- Install the drivers & software (Windows® XP Home/XP Professional/Windows Vista®/Windows® 7)
- Install the drivers & software (Mac OS X 10.4.11, 10.5.x, 10.6.x)
- Install Optional Applications Windows®
- For Network Users
- Consumables
- brother ARL/ASA/NZ
- Start Here
32
For Wireless Network Users
18
One-push configuration
using WPS or AOSS™
(Windows
®
and
Macintosh)
a Confirm your wireless access point/router has
the WPS or AOSS™ symbol as shown below.
b Place the Brother machine within range of your
WPS or AOSS™ access point/router. The
range may differ depending on your
environment. Refer to the instructions provided
with your access point/router.
c On your machine, press Menu.
Press s or t to display Network, and then
press Network.
Press WLAN.
Press s or t to display WPS/AOSS, and then
press WPS/AOSS.
When Network I/F switched to
Wireless. is displayed, press Yes to accept.
This will start the wireless setup wizard.
To cancel, press No.
d When the LCD shows Start WPS or AOSS,
press the WPS or AOSS™ button on your
wireless access point/router. See the user’s
guide of your wireless access point/router for
instructions.
Then press OK and your machine will now
automatically detect which mode (WPS or
AOSS™) your wireless access point/router
uses and try to connect to your wireless
network.
e A connection result message appears for
60 seconds on the LCD and a WLAN report will
automatically be printed.
If the connection failed, check the error code on
the printed report and refer to Troubleshooting
on page 33.
Wireless setup is now complete. A four
level indicator at the upper left of your
machine’s LCD will show the wireless
signal strength of your access
point/router.
To install MFL-Pro Suite, continue to
step 19.
For Windows
®
Users:
Now go to
Page 35
For Macintosh Users:
Now go to
Page 38
Note
If your wireless access point/router supports WPS
(PIN Method), you can also configure your
machine using the PIN (Personal Identification
Number) Method. uuNetwork User’s Guide:
Configuration using the PIN Method of Wi-Fi
Protected Setup