Quick Setup Guide
Table Of Contents
- Quick Setup Guide MFC-J650DW MFC-J870DW MFC-J875DW
- Start Here
- 1 Unpack the machine and check the components
- 2 Connect the power cord and telephone line
- 3 Install the ink cartridges
- 4 Load plain Letter/A4 paper
- 5 Check the print quality
- 6 Set the date and time
- 7 Choose your language (if needed)
- 8 Choose the correct Receive Mode
- 9 Set your Station ID
- 10 Transmission Verification Report
- 11 Set Tone or Pulse dialing mode (Canada only)
- 12 Set the telephone line compatibility (VoIP)
- 13 Automatic Daylight Saving Time
- 14 Choose your connection type
- For Windows® USB interface users (Windows® XP Home/XP Professional/Windows Vista®/Windows® 7/Windows® 8)
- For Macintosh USB interface users (Mac OS X v10.6.8, 10.7.x, 10.8.x)
- For Windows® wired network interface users (MFC-J870DW/J875DW only) (Windows® XP Home/XP Professional/Windows Vista®/Windows® 7/Windows® 8)
- For Macintosh wired network interface users (MFC-J870DW/J875DW only) (Mac OS X v10.6.8, 10.7.x, 10.8.x)
- For wireless network interface users
- 15 Before you begin
- 16 Choose your wireless setup method
- 17 Setup using the CD-ROM (Windows® and Macintosh)
- 17 Manual setup from the control panel using the Setup Wizard (Windows®, Macintosh and mobile devices)
- 17 One-push setup using WPS or AOSS™ (Windows®, Macintosh and mobile devices)
- Troubleshooting
- Install the drivers & software (Windows® XP Home/XP Professional/Windows Vista®/Windows® 7/Windows® 8)
- Install the drivers & software (Mac OS X v10.6.8, 10.7.x, 10.8.x)
- Install Optional Applications Windows®
- For Network Users
- Other Information
- Consumables
- brother USA/CAN
- Start Here
38
Windows
®
Wireless Network
d When the Firewall/AntiVirus detected screen
appears, choose Change the Firewall port
settings to enable network connection and
continue with the installation.
(Recommended), and then click Next.
If you are not using the Windows
®
Firewall, see
the instructions provided with your firewall
software for information on how to add the
following network ports.
For network scanning, add UDP port 54925.
For network PC-Fax receiving, add UDP port
54926.
If you still have trouble with your network
connection, add UDP ports 137 and 161.
e Choose your machine from the list, and then
click Next.
f The installation of the Brother drivers will
automatically start. The installation screens
appear one after another.
g If the Environmental Advice for Imaging
Equipment screen appears, click Next.
h When the On-Line Registration screen
appears, follow the on-screen instructions.
Click Next.
i If you do not want to set your machine as the
default printer, clear the Set as Default Printer
check box, and then click Next.
j When the Setup is Complete window
appears, confirm the settings, and then click
Next.
NOTE
• If your machine is not found over the network,
confirm your settings by following the
on-screen instructions. If you encounter this
failure, go to step 16-b on page 30 and setup
the wireless connection again.
• If you are using WEP and the Touchscreen
displays Connected but your machine is not
found on the network, make sure you entered
the WEP key correctly. The WEP key is
case-sensitive.
NOTE
• DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
• If the Windows Security screen appears, click
the check box and click Install to complete the
installation correctly.
NOTE
The Brother Trial Photo Print screen appears
only once after restarting.
We recommend you try the Brother Trial Photo
Print selection to see the high quality output
available from your Brother machine.