Online User's Guide MFC-J985DW © 2016 Brother Industries, Ltd. All rights reserved.
Home > Table of Contents Table of Contents Before You Use Your Brother Machine ............................................................................................... 1 Applicable Models .......................................................................................................................................... 2 Definitions of Notes ........................................................................................................................................
Home > Table of Contents Print a Photo (Mac) ............................................................................................................................ 88 Print a Document (Mac) ..................................................................................................................... 89 Print on Both Sides of the Paper Automatically (Automatic 2-sided Printing) (Mac) .......................... 90 Print More Than One Page on a Single Sheet of Paper (N in 1) (Mac) ................
Home > Table of Contents Send a Fax at a Specified Time (Delayed Fax)................................................................................ 217 Cancel a Fax in Progress ................................................................................................................. 218 Check and Cancel a Pending Fax.................................................................................................... 219 Fax Polling.....................................................................
Home > Table of Contents Learn about Network Management Software and Utilities ............................................................... 356 Additional Methods of Configuring Your Brother Machine for a Wireless Network .................................... 357 Before Configuring Your Brother Machine for a Wireless Network................................................... 358 Configure Your Machine for a Wireless Network Using the One Push Method of Wi-Fi Protected Setup™ (WPS) or AOSS™................
Home > Table of Contents Paper is Jammed in the Front of the Machine (Jam B Front)........................................................... 435 Paper is Jammed in the Back of the Machine (Jam C Rear) ........................................................... 438 If You Are Having Difficulty with Your Machine .......................................................................................... 440 Paper Handling and Printing Problems ...................................................................
Home > Before You Use Your Brother Machine Before You Use Your Brother Machine • Applicable Models • Definitions of Notes • Notice - Disclaimer of Warranties (USA and Canada) • Trademarks • Important Note 1
Home > Before You Use Your Brother Machine > Applicable Models Applicable Models This User's Guide applies to the following models: 2.
Home > Before You Use Your Brother Machine > Definitions of Notes Definitions of Notes We use the following symbols and conventions throughout this User's Guide: WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injuries. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injuries.
Home > Before You Use Your Brother Machine > Notice - Disclaimer of Warranties (USA and Canada) Notice - Disclaimer of Warranties (USA and Canada) BROTHER’S LICENSOR(S), AND THEIR DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS (COLLECTIVELY BROTHER’S LICENSOR) MAKE NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THE SOFTWARE.
Home > Before You Use Your Brother Machine > Trademarks Trademarks Microsoft, Windows, Windows Vista, Windows Server, SharePoint, Internet Explorer, Word, Excel, PowerPoint, OneNote, OneDrive and Windows Phone are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Apple, Mac, Safari, iPad, iPad mini, iPhone, iPod touch and OS X are trademarks of Apple Inc., registered in the United States and other countries.
Home > Before You Use Your Brother Machine > Important Note Important Note • Do not use this product outside the country of purchase as it may violate the wireless telecommunication and power regulations of that country. • Not all models are available in all countries. • Windows® XP in this document represents Windows® XP Professional, Windows® XP Professional x64 Edition and Windows® XP Home Edition.
Home > Introduction to Your Brother Machine Introduction to Your Brother Machine • Before Using Your Machine • Control Panel Overview • LCD Overview • Settings Screen Overview • Navigate the Touchscreen • Access Brother Utilities (Windows®) 7
Home > Introduction to Your Brother Machine > Before Using Your Machine Before Using Your Machine Before attempting any printing operation, confirm the following: • Make sure you have installed the Brother software and drivers. • For USB or network cable users: Make sure the interface cable is physically secure. Selecting the correct type of paper For high quality printing, it is important to select the correct type of paper.
Home > Introduction to Your Brother Machine > Control Panel Overview Control Panel Overview 1 2 3 4 NFC (Near Field Communication) logo 1. • If your Android™ device supports the NFC feature, you can print from your device or scan documents to your device by touching it to the NFC logo on the control panel. You must download and install Brother iPrint&Scan to your Android™ device to use this feature. • Make sure the NFC settings of both your Brother machine and your Android™ device are set to On.
Press and hold down to turn off the machine. The touchscreen will display [Shutting Down] and will stay on for a few seconds before turning itself off. If you have connected an external telephone or TAD, it is always available. If you turn off the machine using , it will still clean the print head periodically to maintain print quality. To prolong print head life, provide better ink efficiency, and maintain print quality, keep your machine connected to a power source at all times.
Home > Introduction to Your Brother Machine > LCD Overview LCD Overview There are two Home screens that you can access by pressing d or c. From the Home screens, you can access Wi-Fi setup, Shortcuts, Ink levels and Setup screens. Home Screen 1 1 2 4 5 3 6 7 This screen shows the machine’s status when the machine is idle. This Home screen is also called the Ready Mode screen. When displayed, this indicates that your machine is Ready for the next command.
Your machine has not been connected to the wireless access point. Press this button to configure wireless settings. For more detailed information, see the Quick Setup Guide. Wireless network is connected. A three-level indicator in each of the Home screens displays the current wireless signal strength. The wireless access point cannot be detected. The wireless setting is disabled. You can configure wireless settings by pressing the Wireless Status button. 4.
Press to connect the Brother machine to an Internet service. For more detailed information, see the Web Connect Guide: support.brother.com/manuals • [Apps] Press to connect the Brother machine to the Brother Apps service. For more detailed information, see the Web Connect Guide: support.brother.com/manuals 8. [Stored Fax(es):] 8 When [Fax Preview] is set to [Off], [Stored Fax(es)] displays how many received faxes are in the machine's memory. Press [Print] to print the faxes. 9.
Related Information • Introduction to Your Brother Machine • Message from Brother • Reduce Printing Noise • Reset Functions • Reset Your Brother Machine • Check the Ink Volume • Settings Screen Overview • Error and Maintenance Messages 14
Home > Introduction to Your Brother Machine > LCD Overview > Message from Brother Message from Brother If you use Brother Web Connect and [New Function Notice] is set to [On], notifications about cloud services will appear on the Home screen. Check for new notifications by pressing [Detail].
Home > Introduction to Your Brother Machine > Settings Screen Overview Settings Screen Overview The touchscreen shows the machine's status when you press [Settings]. Use the Settings menu to access all of your Brother machine's settings. 4 5 1 6 2 7 3 8 1. [Maintenance] Press to access the [Maintenance] menu. Use options in the Maintenance menu to check and improve print quality, clean the print head and check the ink volume. 2. [Quiet Mode] Displays the Quiet Mode setting.
8. [All Settings] Press to access a menu of all of your machine's settings.
Home > Introduction to Your Brother Machine > Navigate the Touchscreen Navigate the Touchscreen • Press your finger on the touchscreen to display and access all the settings and features and their available options. Press d c or a b to scroll through them. IMPORTANT DO NOT press the touchscreen with a sharp object such as a pen or stylus. It may damage the machine. DO NOT touch the touchscreen immediately after plugging in the power cord or turning on the machine. Doing this may cause an error.
Home > Introduction to Your Brother Machine > Access Brother Utilities (Windows®) Access Brother Utilities (Windows®) Brother Utilities is an application launcher that offers convenient access to all Brother applications installed on your computer. 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 Click • (Start) > All Programs > Brother > Brother Utilities. Windows® 8 Tap or click • (Brother Utilities) either on the Start screen or the desktop. Windows® 8.
Home > Introduction to Your Brother Machine > Access Brother Utilities (Windows®) > Uninstall the Brother Software and Drivers (Windows®) Uninstall the Brother Software and Drivers (Windows®) 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 Click • (Start) > All Programs > Brother > Brother Utilities. Windows® 8 Tap or click • (Brother Utilities) either on the Start screen or the desktop. Windows® 8.
Home > Paper Handling Paper Handling • Load Paper • Load Documents 21
Home > Paper Handling > Load Paper Load Paper • Load Paper in the Paper Tray • Load Photo or Photo L Paper in Photo Bypass Tray • Load Paper in the Manual Feed Slot • Unprintable Area • Paper Settings • Acceptable Paper and Other Print Media • Error and Maintenance Messages • Paper Handling and Printing Problems 22
Home > Paper Handling > Load Paper > Load Paper in the Paper Tray Load Paper in the Paper Tray • Load Cut-Sheet Paper or Photo 2L Paper in the Paper Tray • Load Legal Size Paper in the Paper Tray • Load Photo Paper in the Paper Tray • Load Envelopes in the Paper Tray 23
Home > Paper Handling > Load Paper > Load Paper in the Paper Tray > Load Cut-Sheet Paper or Photo 2L Paper in the Paper Tray Load Cut-Sheet Paper or Photo 2L Paper in the Paper Tray • If the [Check Paper] setting is set to [On] and you pull the paper tray out of the machine, a message appears on the LCD asking if you want to change the paper type and paper size. Change the Paper Size and Paper Type settings if needed, following the on-screen instructions.
1 2 5. Fan the stack of paper well to avoid paper jams and misfeeds. Always make sure the paper is not curled or wrinkled. 6. Gently load paper in the paper tray with the printing surface face down. Make sure the paper is flat in the tray and the paper length guide (1) touches the edges of the paper.
IMPORTANT • Be careful not to push the paper in too far; it may lift at the back of the tray and cause paper feed problems. • Loading more than 20 sheets of Photo 2L (5" x 7")/(13 x 18 cm) paper may cause paper jams. To add paper before the tray is empty, remove the paper from the tray and combine it with the paper you are adding. Always fan the stack of paper well to prevent the machine from feeding multiple pages. 7. Gently adjust the paper width guides (1) to fit the paper.
Related Information • Load Paper in the Paper Tray • Change the Check Paper Size Setting • Choose the Right Print Media • Change the Paper Size and Paper Type 27
Home > Paper Handling > Load Paper > Load Paper in the Paper Tray > Load Legal Size Paper in the Paper Tray Load Legal Size Paper in the Paper Tray • If the [Check Paper] setting is set to [On] and you pull the paper tray out of the machine, a message appears on the LCD asking if you want to change the paper type and paper size. Change the Paper Size and Paper Type settings if needed, following the on-screen instructions. • Load only one size and type of paper in the paper tray at a time.
5. Gently press and slide the paper width guides (1) and the paper length guide (2) to fit the paper size. 1 2 6. Fan the stack of paper well to avoid paper jams and misfeeds. Always make sure the paper is not curled or wrinkled. 7. Gently load paper in the paper tray with the printing surface face down.
Make sure the paper is flat in the tray and the paper length guide (1) touches the edges of the paper. 1 IMPORTANT Be careful not to push the paper in too far; it may lift at the back of the tray and cause paper feed problems. To add paper before the tray is empty, remove the paper from the tray and combine it with the paper you are adding. Always fan the stack of paper well to prevent the machine from feeding multiple pages. 8. Gently adjust the paper width guides to fit the paper.
11. While holding the paper tray in the machine, pull out the paper support (1) until it locks into place, and then unfold the paper support flap (2).
Home > Paper Handling > Load Paper > Load Paper in the Paper Tray > Load Photo Paper in the Paper Tray Load Photo Paper in the Paper Tray • If the [Check Paper] setting is set to [On] and you pull the paper tray out of the machine, a message appears on the LCD asking if you want to change the paper type and paper size. Change the Paper Size and Paper Type settings if needed, following the on-screen instructions. • Load only one size and type of paper in the paper tray at a time.
1 2 5. Close the output paper tray cover. 6. Load up to 20 sheets of Photo paper with the printing surface face down. Loading more than 20 sheets of photo paper may cause paper jams. 7. Gently adjust the paper guides (1) to fit the paper. Make sure the paper width guides touch the edges of the paper and the paper is flat in the tray. 1 8. Slowly push the paper tray completely into the machine.
9. While holding the paper tray in the machine, pull out the paper support (1) until it locks into place, and then unfold the paper support flap (2).
Home > Paper Handling > Load Paper > Load Paper in the Paper Tray > Load Envelopes in the Paper Tray Load Envelopes in the Paper Tray • If the [Check Paper] setting is set to [On] and you pull the paper tray out of the machine, a message appears on the LCD asking if you want to change the paper type and paper size. Change the Paper Size and Paper Type settings if needed, following the on-screen instructions. • Load only one size and type of paper in the paper tray at a time.
1 2 IMPORTANT If envelopes are "double-feeding," load one envelope in the paper tray at a time. 5. Close the output paper tray cover. 6. Slowly push the paper tray completely into the machine. 7. While holding the paper tray in the machine, pull out the paper support (1) until it locks into place, and then unfold the paper support flap (2).
• Choose the Right Print Media • Change the Paper Size and Paper Type 37
Home > Paper Handling > Load Paper > Load Photo or Photo L Paper in Photo Bypass Tray Load Photo or Photo L Paper in Photo Bypass Tray Use the photo bypass tray, which is located on the top of the output paper tray cover, to print on Photo (4" x 6")/(10 x 15 cm) or Photo L (3.5" x 5")/(89 x 127 mm) size paper. • In Canada, the photo bypass tray is called the photo paper tray. • When you use the photo bypass tray, you do not have to remove the paper from the tray beneath it.
5. Gently adjust the paper width guides (1) to fit the paper. Make sure the paper width guides touch the edges of the paper and the paper is flat in the tray. 1 6. Slowly push the paper tray completely into the machine. Do not open the paper support and the paper support flap when using the photo bypass tray. Otherwise it is difficult to take out the printouts. IMPORTANT When you have finished printing photos, return the photo bypass tray to the Normal printing position.
• Paper Handling and Printing Problems 40
Home > Paper Handling > Load Paper > Load Paper in the Manual Feed Slot Load Paper in the Manual Feed Slot Load special print media in this slot one sheet at a time. The machine automatically turns on Manual Feed mode when you put paper in the manual feed slot. 1. Open the manual feed slot cover. 2. Lift up the paper support. 3. Slide the manual feed slot paper guides to fit the width of the paper you are using. 4. Load only one sheet of paper in the manual feed slot with the printing surface face up.
When using envelopes, load the envelopes with the printing surface face up and the flap on the left as shown in the illustration. See Related Information. IMPORTANT • DO NOT load more than one sheet of paper in the manual feed slot at any time. Doing this may cause a paper jam. When printing multiple pages, do not feed the next sheet of paper until the Touchscreen displays a message instructing you to feed the next sheet.
• DO NOT load paper in the manual feed slot when you are printing from the paper tray. Doing this may cause a paper jam. 5. Using both hands, push one sheet of paper into the manual feed slot until the front edge touches the paper feed rollers. Let go of the paper when you hear the machine pull it. The LCD displays [Manual Feed Slot ready.]. Read the instruction displayed on the LCD, and then press [OK].
Home > Paper Handling > Load Paper > Unprintable Area Unprintable Area The unprintable area depends on the settings in the application you are using. The figures below show the unprintable areas on cut-sheet paper and envelopes. The machine can print in the shaded areas of cut-sheet paper only when the Borderless print feature is available and turned on. Cut-Sheet Paper Envelopes Top (1) Left (2) Bottom (3) Right (4) Cut-Sheet 0.12 in. (3 mm) 0.12 in. (3 mm) 0.12 in. (3 mm) 0.12 in.
Home > Paper Handling > Load Paper > Paper Settings Paper Settings • Change the Paper Size and Paper Type • Change the Check Paper Size Setting • Shrink Page Size of an Oversized Incoming Fax 45
Home > Paper Handling > Load Paper > Paper Settings > Change the Paper Size and Paper Type Change the Paper Size and Paper Type Set the Paper Size and Paper Type settings for the paper tray. • To get the best print quality, set the machine for the type of paper you are using. • When you change the size of the paper you load in the tray, you must change the Paper Size setting on the LCD at the same time. 1.
Home > Paper Handling > Load Paper > Paper Settings > Change the Check Paper Size Setting Change the Check Paper Size Setting If the Check Paper setting is set to [On] and you pull the paper tray out of the machine, the LCD displays a message asking if you want to change the Paper Size and Paper Type settings. The default setting is [On]. 1. Press [Settings] > [All Settings] > [General Setup] > [Check Paper]. 2. Press [On] or [Off]. 3. Press .
Home > Paper Handling > Load Paper > Acceptable Paper and Other Print Media Acceptable Paper and Other Print Media The print quality can be affected by the type of paper you use in the machine. To get the best print quality for the settings you have chosen, always set the Paper Type to match the type of paper you load. You can use plain paper, inkjet paper (coated paper), glossy paper, recycled paper and envelopes. We recommend testing various paper types before buying large quantities.
Home > Paper Handling > Load Paper > Acceptable Paper and Other Print Media > Recommended Print Media Recommended Print Media For the best print quality, we recommend using the Brother paper listed in the table.
Home > Paper Handling > Load Paper > Acceptable Paper and Other Print Media > Handle and Use Print Media Handle and Use Print Media • Store paper in its original packaging and keep it sealed. Keep the paper flat and away from moisture, direct sunlight and heat. • Avoid touching the shiny (coated) side of photo paper. IMPORTANT DO NOT use the following kinds of paper: • Damaged, curled, wrinkled, or irregularly shaped 1 1 1. 0.08 in. (2 mm) or greater curl may cause jams to occur.
Home > Paper Handling > Load Paper > Acceptable Paper and Other Print Media > About Envelopes About Envelopes • Use envelopes that weigh from 20 to 25 lb (80 to 95 g/m²). • Some envelope sizes require that you set margins in the application. Make sure you do a test print first before printing many envelopes.
• Load Envelopes in the Paper Tray • Load Paper in the Manual Feed Slot 52
Home > Paper Handling > Load Paper > Acceptable Paper and Other Print Media > Choose the Right Print Media Choose the Right Print Media • Paper Type and Paper Size for Each Operation • Paper Capacity of the Paper Trays • Paper Weight and Thickness • Load Cut-Sheet Paper or Photo 2L Paper in the Paper Tray • Load Photo Paper in the Paper Tray • Load Envelopes in the Paper Tray • Load Paper in the Manual Feed Slot 53
Home > Paper Handling > Load Paper > Acceptable Paper and Other Print Media > Choose the Right Print Media > Paper Type and Paper Size for Each Operation Paper Type and Paper Size for Each Operation Paper Type Cut-Sheet Cards Envelopes Paper Size Usage Fax Copy Photo Capture Printer Letter 8 1/2 x 11 in. (215.9 x 279.4 mm) Yes Yes Yes Yes A4 8.3 x 11.7 in. (210 x 297 mm) Yes Yes Yes Yes Legal 8 1/2 x 14 in. (215.9 x 355.6 mm) Yes Yes - Yes Executive 7 1/4 x 10 1/2 in. (184.
Home > Paper Handling > Load Paper > Acceptable Paper and Other Print Media > Choose the Right Print Media > Paper Capacity of the Paper Trays Paper Capacity of the Paper Trays Paper Tray Paper Size Paper Types No.
Home > Paper Handling > Load Paper > Acceptable Paper and Other Print Media > Choose the Right Print Media > Paper Weight and Thickness Paper Weight and Thickness Paper Type Cut-Sheet Cards Weight Thickness Plain Paper 1, Recycled Paper 1 17 to 32 lb (64 to 120 g/m²) 3 to 6 mil (0.08 to 0.15 mm) Inkjet Paper 17 to 53 lb (64 to 200 g/m²) 3 to 10 mil (0.08 to 0.25 mm) Glossy Paper 2 Up to 58 lb (Up to 220 g/m²) Up to 10 mil (Up to 0.
Home > Paper Handling > Load Documents Load Documents • Load Documents in the Automatic Document Feeder (ADF) • Load Documents on the Scanner Glass • Unscannable Area 57
Home > Paper Handling > Load Documents > Load Documents in the Automatic Document Feeder (ADF) Load Documents in the Automatic Document Feeder (ADF) The ADF can hold up to 20 pages, and feeds each sheet individually. Documents that are longer than 11.7 in. (297 mm) must be fed one page at a time. Use paper that is within the sizes and weights shown in the table. Always fan the pages before placing them in the ADF. Document Sizes and Weights Length 5.8 to 14 in. (148 to 355.6 mm) Width 5.8 to 8.5 in.
• Copy a Document • Error and Maintenance Messages • Telephone and Fax problems • Other Problems 59
Home > Paper Handling > Load Documents > Load Documents on the Scanner Glass Load Documents on the Scanner Glass Use the scanner glass to fax, copy, or scan one page at a time. Document Sizes Supported Length: Up to 11.7 in. (297 mm) Width: Up to 8.5 in. (215.9 mm) Weight: Up to 4.4 lb (2 kg) (ADF models) To use the scanner glass, the ADF must be empty and the ADF document support must be closed. 1. Lift the document cover. 2.
• Other Problems 61
Home > Paper Handling > Load Documents > Unscannable Area Unscannable Area The unscannable area of a page depends on the settings in the application you are using. The figures below show the typical unscannable measurements. Usage Fax Document Size Letter Top (1) Left (2) Bottom (3) Right (4) 0.12 in. (3 mm) 0.16 in. (4 mm) Legal Copy A4 0.12 in. (3 mm) 1 All paper sizes 0.12 in. (3 mm) Scan 1 0.04 in. (1 mm) 0.04 in. (1 mm) The unscannable area is 0.04 in. (1 mm) when using the ADF.
Home > Print Print • Print from Your Computer (Windows®) • Print from Your Computer (Mac) 63
Home > Print > Print from Your Computer (Windows®) Print from Your Computer (Windows®) • Print a Photo (Windows®) • Print a Document (Windows®) • Cancel a Print Job (Windows®) • Print More Than One Page on a Single Sheet of Paper (N in 1) (Windows®) • Print as a Poster (Windows®) • Print on Both Sides of the Paper Automatically (Automatic 2-sided Printing) (Windows®) • Print as a Booklet Automatically (Windows®) • Print a Color Document in Grayscale (Windows®) • Prevent Smudged Printouts and Paper Jams Whe
Home > Print > Print from Your Computer (Windows®) > Print a Photo (Windows®) Print a Photo (Windows®) 1. Select the print command in your application. 2. Select Brother MFC-XXXX Printer (where XXXX is the name of your model), and then click the printing properties or preferences button. The printer driver window appears. 3. Make sure you have loaded the correct media in the paper tray.
• Print Settings (Windows®) 66
Home > Print > Print from Your Computer (Windows®) > Print a Document (Windows®) Print a Document (Windows®) 1. Select the print command in your application. 2. Select Brother MFC-XXXX Printer (where XXXX is the name of your model), and then click the printing properties or preferences button. The printer driver window appears. 3. Make sure you have loaded the correct size paper in the paper tray. 4. Click the Media Type drop-down list, and then select the type of paper you are using.
Home > Print > Print from Your Computer (Windows®) > Cancel a Print Job (Windows®) Cancel a Print Job (Windows®) If a print job was sent to the print queue and did not print, or was sent to the print queue in error, you may have to delete it to allow subsequent jobs to print. 1. Double-click the printer icon in the task tray. 2. Select the print job you want to cancel. 3. Click the Document menu. 4. Select Cancel. 5. Click Yes.
Home > Print > Print from Your Computer (Windows®) > Print More Than One Page on a Single Sheet of Paper (N in 1) (Windows®) Print More Than One Page on a Single Sheet of Paper (N in 1) (Windows®) 1. Select the print command in your application. 2. Select Brother MFC-XXXX Printer (where XXXX is the name of your model), and then click the printing properties or preferences button. The printer driver window appears. 3.
Home > Print > Print from Your Computer (Windows®) > Print as a Poster (Windows®) Print as a Poster (Windows®) Enlarge your print size and print the document in poster mode. 1. Select the print command in your application. 2. Select Brother MFC-XXXX Printer (where XXXX is the name of your model), and then click the printing properties or preferences button. The printer driver window appears. 3. Click the Multiple Page drop-down list, and then select the 1 in 2x2 Pages or 1 in 3x3 Pages option. 4.
Home > Print > Print from Your Computer (Windows®) > Print on Both Sides of the Paper Automatically (Automatic 2-sided Printing) (Windows®) Print on Both Sides of the Paper Automatically (Automatic 2-sided Printing) (Windows®) • Make sure the back cover is closed. • If paper is curled, straighten it and put it back in the paper tray. • Use regular paper or thin paper. DO NOT use bond paper. • If the paper is thin, it may wrinkle. 1. Select the print command in your application. 2.
Option for Portrait Description Short Edge (Top) Short Edge (Bottom) Option for Landscape Description Long Edge (Top) Long Edge (Bottom) Short Edge (Right) Short Edge (Left) 7. Select the Binding Offset check box if you want to specify the offset for binding in inches or millimeters. 8. Click OK to return to the printer driver window. 9. Change other printer settings if needed. The Borderless feature is not available when using this option. 10. Click OK again, and then complete your print operation.
Related Information • Print from Your Computer (Windows®) • Print Settings (Windows®) • Print as a Booklet Automatically (Windows®) 73
Home > Print > Print from Your Computer (Windows®) > Print as a Booklet Automatically (Windows®) Print as a Booklet Automatically (Windows®) Use this option to print a document in booklet format using 2-sided printing. The document's pages will be arranged according to the correct page number and will allow you to fold at the center of the print output without having to change the order of the printed pages. • Make sure the back cover is closed.
Option for Landscape Description Top Binding Bottom Binding 7. Select one of the options from the Booklet Printing Method menu. Option Description All Pages at Once Every page will be printed in booklet format (four pages to every piece of paper, two pages per side). Fold your printout in the middle to create the booklet.
Home > Print > Print from Your Computer (Windows®) > Print a Color Document in Grayscale (Windows®) Print a Color Document in Grayscale (Windows®) Grayscale mode makes the print processing speed faster than color mode. If your document contains color, selecting Grayscale mode prints your document in 256 levels of grayscale. 1. Select the print command in your application. 2.
Home > Print > Print from Your Computer (Windows®) > Prevent Smudged Printouts and Paper Jams When Printing on Both Sides of the Paper (Windows®) Prevent Smudged Printouts and Paper Jams When Printing on Both Sides of the Paper (Windows®) Some types of print media may need more drying time when using the 2-sided feature. Change the Advanced 2sided Settings option if you have problems with smudged 2-sided printouts or paper jams. 1. Select the print command in your application. 2.
Home > Print > Print from Your Computer (Windows®) > Use a Preset Print Profile (Windows®) Use a Preset Print Profile (Windows®) Print Profiles are presets designed to give you quick access to frequently-used printing configurations. 1. Select the print command in your application. 2. Select Brother MFC-XXXX Printer (where XXXX is the name of your model), and then click the printing properties or preferences button. The printer driver window appears. 3. Click the Print Profiles tab. 4.
Related Information • Print from Your Computer (Windows®) • Create or Delete Your Print Profile (Windows®) • Print Settings (Windows®) 79
Home > Print > Print from Your Computer (Windows®) > Use a Preset Print Profile (Windows®) > Create or Delete Your Print Profile (Windows®) Create or Delete Your Print Profile (Windows®) Add up to 20 new print profiles with customized settings. 1. Select the print command in your application. 2. Select Brother MFC-XXXX Printer (where XXXX is the name of your model), and then click the printing properties or preferences button. The printer driver window appears. 3.
Home > Print > Print from Your Computer (Windows®) > Change the Default Print Settings (Windows®) Change the Default Print Settings (Windows®) When you change an application's print settings, the changes only apply to documents printed with that application. To change print settings for all Windows® applications, you must configure the printer driver properties. 1. Do one of the following: • For Windows® XP and Windows Server® 2003 Click Start > Printers and Faxes.
Home > Print > Print from Your Computer (Windows®) > Print Settings (Windows®) Print Settings (Windows®) Basic Tab 1. Media Type Select the type of media you want to use. To achieve the best print results, the machine automatically adjusts its print settings according to the selected media type. Slow Drying Paper Select this option if you use a type of plain paper on which ink dries slowly. This option may cause slight blurring of the text. 2. Print Quality Select the print resolution you want.
Borderless Select this option to print photos without borders. Because the image data is created slightly larger than the paper size you are using, this will cause some cropping of the photo edges. You may not be able to select the Borderless option for some combinations of media type and quality, or from some applications. 4. Color Mode Select the color mode to suit your preference. 5. Orientation Select the orientation (portrait or landscape) of your printout.
Advanced Tab 1. Color / Grayscale Select color or grayscale printing. The print speed is faster in grayscale mode than it is in color mode. If your document contains color and you select grayscale mode, your document will be printed using 256 levels of grayscale. Settings button Click this button to select the Color Enhancement feature. This feature analyzes your image to improve its sharpness, white balance and color density.
Fit to Paper Size Select this option to enlarge or reduce the document pages to fit a specified paper size. When you select this option, select the paper size you want from the drop-down list. Free Select this option to enlarge or reduce the document pages manually. When you select this option, type a value into the field. 4. Mirror Print Select this option to reverse the printed image on the page horizontally from left to right. 5. Reverse Print Select this option to rotate the printed image 180 degrees.
• Change the Default Print Settings (Windows®) 86
Home > Print > Print from Your Computer (Mac) Print from Your Computer (Mac) • Print a Photo (Mac) • Print a Document (Mac) • Print on Both Sides of the Paper Automatically (Automatic 2-sided Printing) (Mac) • Print More Than One Page on a Single Sheet of Paper (N in 1) (Mac) • Print a Color Document in Grayscale (Mac) • Prevent Smudged Printouts and Paper Jams When Printing on Both Sides of the Paper (Mac) • Print Options (Mac) 87
Home > Print > Print from Your Computer (Mac) > Print a Photo (Mac) Print a Photo (Mac) 1. Make sure you have loaded the correct media in the paper tray. IMPORTANT • We recommend using the photo bypass tray located on the top of the output tray cover to print on Photo (4" x 6")/(10 x 15 cm) and Photo L (3.5" x 5")/(9 x 13 cm) paper. (available only for certain models) • For best results, use Brother paper.
Home > Print > Print from Your Computer (Mac) > Print a Document (Mac) Print a Document (Mac) 1. Make sure you have loaded the correct size paper in the paper tray. 2. From an application, such as Apple TextEdit, click the File menu, and then select Print. 3. Select Brother MFC-XXXX (where XXXX is your model name). For more page setup options, click the Show Details button. 4. Click the Paper Size pop-up menu, and then select your paper size. 5.
Home > Print > Print from Your Computer (Mac) > Print on Both Sides of the Paper Automatically (Automatic 2-sided Printing) (Mac) Print on Both Sides of the Paper Automatically (Automatic 2-sided Printing) (Mac) 1. From an application, such as Apple TextEdit, click the File menu, and then select Print. 2. Select Brother MFC-XXXX (where XXXX is your model name). For more page setup options, click the Show Details button. 3. Select the Orientation option that matches the way you want the document to print.
Home > Print > Print from Your Computer (Mac) > Print More Than One Page on a Single Sheet of Paper (N in 1) (Mac) Print More Than One Page on a Single Sheet of Paper (N in 1) (Mac) 1. From an application, such as Apple TextEdit, click the File menu, and then select Print. 2. Select Brother MFC-XXXX (where XXXX is your model name). For more page setup options, click the Show Details button. 3. Click the application pop-up menu, and then select Layout. The Layout setting options appear. 4.
Home > Print > Print from Your Computer (Mac) > Print a Color Document in Grayscale (Mac) Print a Color Document in Grayscale (Mac) Grayscale mode makes the print processing speed faster than color mode. If your document contains color, selecting Grayscale mode prints your document in 256 levels of grayscale. 1. From an application, such as Apple TextEdit, click the File menu, and then select Print. 2. Select Brother MFC-XXXX (where XXXX is your model name).
Home > Print > Print from Your Computer (Mac) > Prevent Smudged Printouts and Paper Jams When Printing on Both Sides of the Paper (Mac) Prevent Smudged Printouts and Paper Jams When Printing on Both Sides of the Paper (Mac) Some types of print media may need more drying time when using the 2-sided feature. Change the Advanced 2sided Settings option if you have problems with smudged 2-sided printouts or paper jams. 1. From an application, such as Apple TextEdit, click the File menu, and then select Print.
Home > Print > Print from Your Computer (Mac) > Print Options (Mac) Print Options (Mac) Page Setup 1. Paper Size Select the size of the paper you want to use. You can either choose from standard paper sizes or create a custom paper size. 2. Orientation Select the orientation (portrait or landscape) of your printout. If your application contains a similar setting, we recommend that you set the orientation using the application. 3.
Layout 1. Pages per Sheet Select the number of pages to print on a single sheet of paper. 2. Layout Direction Select the page order when printing multiple pages on a single sheet of paper. 3. Border Select the type of border to use when printing multiple pages on a single sheet of paper. 4. Two-Sided (available only for certain models) Select whether to print on both sides of the paper. 5. Reverse page orientation Select this option to rotate the printed image 180 degrees. 6.
Paper Handling 1. Collate pages Select this option to print sets of multi-page documents in the original page order. When this option is selected, one complete copy of your document will print, and then reprint according to the number of copies you choose. If this option is not selected, then each page will print according to the number of copies chosen before the next page of the document is printed. 2. Page Order Select the page order. 3.
Print Settings 1. Media Type Select the type of media you want to use. To achieve the best print results, the machine automatically adjusts its print settings according to the selected media type. 2. Slow Drying Paper Select this option if you use a type of plain paper on which ink dries slowly. This option may cause slight blurring of the text. 3. Print Quality Select the print resolution you want.
4. Color / Grayscale Select color or grayscale printing. The print speed is faster in grayscale mode than it is in color mode. If your document contains color and you select grayscale mode, your document will be printed using 256 levels of grayscale. 5. Advanced Change Data Transfer Mode Select the print data transfer mode to improve print quality or print speed. Advanced 2-sided Settings Select the print speed for 2-sided printing.
1. Color Mode Select the color mode to suit your preference. 2. Advanced Color Settings Click the disclosure triangle to select the Color Enhancement feature. This feature analyzes your image to improve its sharpness, white balance and color density. This process may take several minutes depending on the size of the image and the specifications of your computer.
Home > Scan Scan • Scan Using the Scan Button on Your Brother Machine • Scan from Your Computer (Windows®) • Scan from Your Computer (Mac) 100
Home > Scan > Scan Using the Scan Button on Your Brother Machine Scan Using the Scan Button on Your Brother Machine • Scan Photos and Graphics • Save Scanned Data to a Folder as a PDF File • Save Scanned Data to a Memory Card or USB Flash Drive • Scan Multiple Business Cards and Photos (Auto Crop) • Scan to an Editable Text File Using OCR • Scan to E-mail Attachment • Web Services for Scanning on Your Network (Windows Vista® SP2 or greater, Windows® 7, Windows® 8 and Windows® 10) • Change Scan Button Setti
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Scan Photos and Graphics Scan Photos and Graphics Send scanned photos or graphics directly to your computer. Use the Scan button on the machine to make temporary changes to the scan settings. To make permanent changes, use Brother's ControlCenter software. 1. Load your document. 2. Press [Scan] > [to Image]. 3.
Related Information • Scan Using the Scan Button on Your Brother Machine 103
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Save Scanned Data to a Folder as a PDF File Save Scanned Data to a Folder as a PDF File Scan documents and save them to a folder on your computer as PDF files. Use the Scan button on the machine to make temporary changes to the scan settings. To make permanent changes, use Brother's ControlCenter software. 1. Load your document. 2. Press [Scan] > [to File]. 3.
The machine starts scanning. If using the machine's scanner glass, follow the LCD instructions to complete the scanning job.
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Save Scanned Data to a Memory Card or USB Flash Drive Save Scanned Data to a Memory Card or USB Flash Drive Scan documents and save them directly to a memory card or USB flash drive without using a computer. 1. Load your document. 2. Open the machine's media slot cover. 3. Insert a memory card or USB flash drive into your machine. The LCD screen automatically changes. 4. Press [Scan to Media]. 5.
Related Information • Scan Using the Scan Button on Your Brother Machine • Memory Card or USB Flash Drive Information • Scan-to Media Settings 107
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Save Scanned Data to a Memory Card or USB Flash Drive > Memory Card or USB Flash Drive Information Memory Card or USB Flash Drive Information Your Brother machine has media drives (slots) for use with common data storage and digital camera media. IMPORTANT The USB direct interface supports only USB flash drives, PictBridge-compatible cameras, or digital cameras that use the USB mass storage standard. Other USB devices are not supported.
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Save Scanned Data to a Memory Card or USB Flash Drive > Scan-to Media Settings Scan-to Media Settings [Scan Type] / [Resolution] / [File Type] Selecting a higher dots per inch (dpi) setting increases the details captured during the scan; however, file size and transfer time also increase. The table below shows the available quality settings and file types.
Related Information • Save Scanned Data to a Memory Card or USB Flash Drive 110
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Scan Multiple Business Cards and Photos (Auto Crop) Scan Multiple Business Cards and Photos (Auto Crop) You can scan multiple documents placed on the scanner glass. The machine will scan each document and use the Auto Crop feature to create separate files or a single multi-page file. Guidelines for Auto Crop 1. 0.4 in. (10 mm) or greater 2. 0.8 in.
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Scan to an Editable Text File Using OCR Scan to an Editable Text File Using OCR Your machine can convert characters in a scanned document to text data using optical character recognition (OCR) technology. You can edit this text using your preferred text-editing application. • Mac Presto! PageManager must be installed on your computer. Download Presto! PageManager from nj.newsoft.com.tw/download/brother/ PM9SEInstaller_BR_multilang2.dmg.
Option Description File Type Select the file format for your document. Scan Size Select the scan size for your document. 7. Press [Start]. The machine starts scanning. If using the machine's scanner glass, follow the LCD instructions to complete the scanning job.
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Scan to E-mail Attachment Scan to E-mail Attachment Send a scanned document as an email attachment. • Use the Scan button on the machine to make temporary changes to the scan settings. To make permanent changes, use Brother's ControlCenter software. • The Scan to E-mail feature does not support Webmail services.
7. Press [Start]. The machine scans the document and saves it as a file attachment. It then launches your email application and opens a new, blank email message with the scanned file attached.
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Web Services for Scanning on Your Network (Windows Vista® SP2 or greater, Windows® 7, Windows® 8 and Windows® 10) Web Services for Scanning on Your Network (Windows Vista® SP2 or greater, Windows® 7, Windows® 8 and Windows® 10) The Web Services protocol enables Windows Vista® (SP2 or greater), Windows® 7, Windows® 8 and Windows® 10 users to scan using a Brother machine on the network. You must install the driver via Web Services.
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Web Services for Scanning on Your Network (Windows Vista® SP2 or greater, Windows® 7, Windows® 8 and Windows® 10) > Use Web Services to Install Drivers Used for Scanning (Windows Vista®, Windows® 7, Windows® 8 and Windows® 10) Use Web Services to Install Drivers Used for Scanning (Windows Vista®, Windows® 7, Windows® 8 and Windows® 10) Use Web Services to monitor printers on the network.
To uninstall drivers, click Uninstall or (Remove device).
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Web Services for Scanning on Your Network (Windows Vista® SP2 or greater, Windows® 7, Windows® 8 and Windows® 10) > Scan Using Web Services from the Brother Machine (Windows Vista® SP2 or greater, Windows® 7, Windows® 8 and Windows® 10) Scan Using Web Services from the Brother Machine (Windows Vista® SP2 or greater, Windows® 7, Windows® 8 and Windows® 10) If you have installed the driver for scanning via Web Services, you can access the Web
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Web Services for Scanning on Your Network (Windows Vista® SP2 or greater, Windows® 7, Windows® 8 and Windows® 10) > Configure Scan Settings for Web Services Configure Scan Settings for Web Services 1. Do one of the following: • Windows Vista® Click • Windows® 7 Click • (Start) > Control Panel > Hardware and Sound > Scanners and Cameras. (Start) > Devices and Printers.
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Change Scan Button Settings from ControlCenter4 (Windows®) Change Scan Button Settings from ControlCenter4 (Windows®) 1. Click the (ControlCenter4) icon in the task tray, and then click Open. 2. Click the Device Settings tab. 3. Click the Device Scan Settings button. The Device Scan Settings dialog box appears. 4. Click the tab for the Scan to action you want to change (Image, OCR, E-mail, or File). 5. Change the settings as needed. 6.
Each tab corresponds to a scan feature, as described below. These settings can be changed. Click the tabs, and then change the settings.
Destination Folder To change the folder for the Image, OCR and E-mail features, click Change. Click the folder icon, and then browse to the folder where you want to save your scanned document. Select the Show Folder option to automatically display the destination folder after scanning to a File. File size Adjust the data compression ratio of the scanned image. Change the file size by moving the File size slider to the right or left. Resolution Select a scanning resolution from the Resolution drop-down list.
• Remove Background Color Remove the base color of documents to make the scanned data more recognizable. When you use this feature, choose from three settings: High, Medium and Low. Default Select this option to restore all settings to their factory setting values.
Home > Scan > Scan Using the Scan Button on Your Brother Machine > Change Scan Button Settings from ControlCenter2 (Mac) Change Scan Button Settings from ControlCenter2 (Mac) 1. In the Finder menu bar, click Go > Applications > Brother, and then double-click the (ControlCenter) icon. The ControlCenter2 screen appears. 2. Hold the control key on your keyboard and click the scan destination (Image, OCR, E-mail, or File) whose settings you want to change. 3. Click the Device Button tab.
OCR Software - Yes - - - Yes - - Destination File Path Yes Yes Yes - File Name Yes Yes Yes Yes Insert Date in File Name Yes Yes Yes Yes Destination Folder Yes Yes Yes Yes Resolution Yes Yes Yes Yes Scan Type Yes Yes Yes Yes Document Size Yes Yes Yes Yes ID Card Scan Yes Yes Yes Yes Advanced Settings Yes Yes Yes Yes Restore Defaults Yes Yes Yes Yes (only available for certain models) OCR Language (only available for certain models) Target Applicatio
Resolution Select a scanning resolution from the Resolution pop-up menu. Higher resolutions take more memory and transfer time, but produce a finer scanned image. Scan Type Select from a range of scan color depths. • Black & White Use for text or line art images. • Gray (Error Diffusion) Use for photographic images or graphics. (Error Diffusion is a method for creating simulated gray images without using true gray dots. Black dots are put in a specific pattern to give a gray appearance.
Home > Scan > Scan from Your Computer (Windows®) Scan from Your Computer (Windows®) There are several ways you can use your computer to scan photos and documents on your Brother machine. Use the software applications provided by Brother, or use your favorite scanning application.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) Scan Using ControlCenter4 Home Mode (Windows®) Use ControlCenter4 Home Mode to access your machine's main features.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) Scan Using ControlCenter4 Home Mode (Windows®) Select Home Mode as the mode setting for ControlCenter4. 1. Load your document. 2. Click the (ControlCenter4) icon in the task tray, and then click Open. 3. Click the Scan tab. 4. Select the Document Type. 5. Change the document's Scan Size, if needed. 6. Click (Scan).
Related Information • Scan Using ControlCenter4 Home Mode (Windows®) • Select Document Type Using ControlCenter4 Home Mode (Windows®) • Change Scan Size Using ControlCenter4 Home Mode (Windows®) • Crop a Scanned Image Using ControlCenter4 Home Mode (Windows®) • Print Scanned Data Using ControlCenter4 Home Mode (Windows®) • Open with an Application Using ControlCenter4 Home Mode (Windows®) 131
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Select Document Type Using ControlCenter4 Home Mode (Windows®) Select Document Type Using ControlCenter4 Home Mode (Windows®) • Select the Document Type option that matches the type of original you want to scan.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Select Document Type Using ControlCenter4 Home Mode (Windows®) > Custom Scan Settings (Windows®) Custom Scan Settings (Windows®) Select Custom in the Document Type list to change advanced scan settings. • Select Custom, and then click the Custom Settings button. The Custom Scan Settings dialog box appears.
Brightness Set the Brightness level by dragging the slider to the right or left to lighten or darken the image. If the scanned image is too light, set a lower brightness level and scan the document again. If the image is too dark, set a higher brightness level and scan the document again. You can also type a value into the field to set the Brightness level. Contrast Increase or decrease the Contrast level by moving the slider to the right or left.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Change Scan Size Using ControlCenter4 Home Mode (Windows®) Change Scan Size Using ControlCenter4 Home Mode (Windows®) For faster scan speeds, select the exact size of your document from the Scan Size drop-down menu. Auto means that the machine will automatically detect the document size.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Crop a Scanned Image Using ControlCenter4 Home Mode (Windows®) Crop a Scanned Image Using ControlCenter4 Home Mode (Windows®) The crop tool on the Image Editing Toolbar lets you trim unwanted areas from your scanned image. Use the Zoom In and Zoom Out tools to help view the image to be cropped. Image Editing Toolbar 1.
a. Expands the scanned image so that the entire image fits in the window. b. Zooms in on the image. c. Zooms out of the image. d. Rotates the image counter-clockwise 90 degrees. e. Rotates the image clockwise 90 degrees. f. Click and drag the frame to adjust the area to be cropped. 3. Click OK. The edited image is displayed in the image viewer.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Print Scanned Data Using ControlCenter4 Home Mode (Windows®) Print Scanned Data Using ControlCenter4 Home Mode (Windows®) Scan a document on your Brother machine, and then print copies using the printer driver features that are available in ControlCenter4. 1. Scan a document. 2. Click Print. a.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Open with an Application Using ControlCenter4 Home Mode (Windows®) Open with an Application Using ControlCenter4 Home Mode (Windows®) The Open with an Application button lets you scan an image directly into your graphics application for editing. 1. Click the Open with an Application button. 2. Select the application from the drop-down list, and then click OK.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Save Scanned Data to a Folder as a PDF File Using ControlCenter4 Home Mode (Windows®) Save Scanned Data to a Folder as a PDF File Using ControlCenter4 Home Mode (Windows®) Select Home Mode as the mode setting for ControlCenter4. 1. Load your document. 2. Click the (ControlCenter4) icon in the task tray, and then click Open. 3. Click the Scan tab. 4. Select the Document Type. 5.
To save the document as a password-protected PDF, select Secure PDF (*.pdf) from the File Type dropdown list, click , and then type the password. 10. In the File Name field, type a prefix for your file name, if needed. 11. Click the folder icon to browse and select the folder where you want to save your scanned documents. 12. Click OK. The scanned document is saved to the destination folder as a PDF.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) > Scan Settings for ControlCenter4 Home Mode (Windows®) Scan Settings for ControlCenter4 Home Mode (Windows®) Settings Applicable Features Open OCR with an Applicati on Send Email Save File Type - Yes Yes Yes Target Application Yes Yes - - OCR Language (available only for certain models) - Yes - - File Name - - - Yes Insert Date in File Name - - - Yes Scan Location - - - Yes S
OCR Language Set the optical character recognition (OCR) language to match the language of the scanned document's text (available only for certain models) . File Name Type a prefix for your file name, if needed. Insert Date in File Name Select to automatically insert the date in the scanned image's file name. Scan Location Select the Folder or SharePoint radio button to specify the destination where you want to save your scanned documents.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) Scan Using ControlCenter4 Advanced Mode (Windows®) ControlCenter4 Advanced Mode gives you more control over the details of your machine's features and allows you to customize one-button scan actions.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) > Scan Photos and Graphics Using ControlCenter4 Advanced Mode (Windows®) Scan Photos and Graphics Using ControlCenter4 Advanced Mode (Windows®) Send scanned photos or graphics directly to your computer. Select Advanced Mode as the mode setting for ControlCenter4. 1. Load your document. 2. Click the (ControlCenter4) icon in the task tray, and then click Open. 3. Click the Scan tab. 4.
5. Change the scan settings, such as file format, file name, destination file path, resolution, or color, if needed. • To change the file name or Destination File Path, click Change. • To preview and configure the scanned image, select the PreScan check box. 6. Click Scan. The machine starts scanning. The image opens in the application you have selected.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) > Save Scanned Data to a Folder as a PDF File Using ControlCenter4 Advanced Mode (Windows®) Save Scanned Data to a Folder as a PDF File Using ControlCenter4 Advanced Mode (Windows®) Scan documents and save them to a folder on your computer as PDF files. Select Advanced Mode as the mode setting for ControlCenter4. 1. Load your document. 2.
4. Click the File button. The scan settings dialog box appears. 5. Click the File Type drop-down list, and then select PDF (*.pdf). To save the document as a password-protected PDF, select Secure PDF (*.pdf) from the File Type dropdown list, click , and then type the password. 6. Click the folder icon to browse and select the folder where you want to save your scanned documents. 7. Change the scan settings, such as file format, file name, resolution or color, if needed.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) > Scan Both Sides of an ID Card Using ControlCenter4 Advanced Mode (Windows®) Scan Both Sides of an ID Card Using ControlCenter4 Advanced Mode (Windows®) Select Advanced Mode as the mode setting for ControlCenter4. 1. Place an ID card on the scanner glass. 2. Click the (ControlCenter4) icon in the task tray, and then click Open. 3. Click the Scan tab.
4. Click the File button. The scan settings dialog box appears. 5. Select the ID Card Scan check box. The instruction dialog box appears. 6. Read the instructions on the screen, and then press OK. 7. Change the scan settings, such as file format, file name, scan location, resolution, or color, if needed. 8. Click Scan. The machine starts scanning one side of the identification card. 9. After the machine has scanned one side, turn over the identification card, and then click Continue to scan the other side.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) > Scan to E-mail Attachment Using ControlCenter4 Advanced Mode (Windows®) Scan to E-mail Attachment Using ControlCenter4 Advanced Mode (Windows®) Send a scanned document as an email attachment. • Select Advanced Mode as the mode setting for ControlCenter4. • The Scan to E-mail feature does not support Webmail services.
5. Change the scan settings, such as file format, file name, destination file path, resolution, or color, if needed. • To change the file name or Destination File Path, click Change. • To preview and configure the scanned image, select the PreScan check box. 6. Click Scan. The machine starts scanning. Your default email application opens and the scanned image is attached to a new, blank email message.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) > Scan to an Editable Text File (OCR) Using ControlCenter4 Advanced Mode (Windows®) Scan to an Editable Text File (OCR) Using ControlCenter4 Advanced Mode (Windows®) Your machine can convert characters in a scanned document to text data using optical character recognition (OCR) technology. You can edit this text using your preferred text-editing application.
5. Change the scan settings, such as file format, file name, destination file path, resolution, or color, if needed. • To change the file name or Destination File Path, click Change. • To preview and configure the scanned image, select the PreScan check box. 6. Click Scan. The machine scans the document, converts it to editable text, and then sends it to your default word processing application.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) > Scan to an Office File Using ControlCenter4 Advanced Mode (Windows®) Scan to an Office File Using ControlCenter4 Advanced Mode (Windows®) Your machine can convert scanned data to a Microsoft® Word file or a Microsoft® PowerPoint® file. • Select Advanced Mode as the mode setting for ControlCenter4.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) > Scan Settings for ControlCenter4 Advanced Mode (Windows®) Scan Settings for ControlCenter4 Advanced Mode (Windows®) Settings Applicable Features Image OCR E-mail File File Type Yes Yes Yes Yes Target Application Yes Yes - - OCR Language (available only for certain models) - Yes - - Destination File Path Yes Yes Yes - File Name Yes Yes Yes Yes Insert Date in File Name Yes Y
• Text (*.txt) • HTML 3.2 (*.htm) • HTML 4.0 (*.htm) • Searchable PDF (*.pdf) • WordPad (*.rtf) • RTF Word 2000 (*.rtf) • WordPerfect 9, 10 (*.wpd) • Microsoft Excel 2003, XP (*.xls) For E-mail and File: • Microsoft Office Word (*.docx) (available only for certain models) • Microsoft Office PowerPoint (*.pptx) (available only for certain models) Target Application Select the destination application from the drop-down list.
• Black & White Use for text or line art images. • Gray (Error Diffusion) Use for photographic images or graphics. (Error Diffusion is a method for creating simulated gray images without using true gray dots. Black dots are put in a specific pattern to give a gray appearance.) • True Gray Use for photographic images or graphics. This mode is more accurate because it uses up to 256 shades of gray. • 24bit Color Use to create an image with the most accurate color reproduction. This mode uses up to 16.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using Nuance™ PaperPort™ 14 or Other Windows® Applications Scan Using Nuance™ PaperPort™ 14 or Other Windows® Applications You can use the Nuance™ PaperPort™ 14 application for scanning. To download the Nuance™ PaperPort™ 14 application, click • (Brother Utilities), select Do More in the left navigation bar, and then click PaperPort.
8. Adjust the settings in the Scanner Setup dialog box, if needed. 9. Click the Document Size drop-down list, and then select your document size. • After you select a document size, adjust the scanning area by holding down the left mouse button and dragging your mouse pointer over the portion you want to scan. 10. Click PreScan if you want to preview your image and crop unwanted portions before scanning. 11. Click Start. The machine starts scanning.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using Nuance™ PaperPort™ 14 or Other Windows® Applications > TWAIN Driver Settings (Windows®) TWAIN Driver Settings (Windows®) 1 2 3 4 5 6 7 8 • Note that the item names and assignable values will vary depending on the machine. • The Brightness option is available only when selecting the Black & White, Gray (Error Diffusion), True Gray, or 24bit Color option from the Scan Type settings.
• 256 Color Use for simple color illustrations that do not need the full color spectrum. This mode uses up to 256 colors to create images. • 24bit Color Use to create an image with the most accurate color reproduction. This mode uses up to 16.8 million colors to scan the image, but it requires the most memory and has the longest transfer time. 4. Reduce Noise Improve and enhance the quality of your scanned images with this selection.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using Windows® Photo Gallery or Windows® Fax and Scan Scan Using Windows® Photo Gallery or Windows® Fax and Scan Windows® Photo Gallery or Windows® Fax and Scan applications are other options that you can use for scanning. • These applications use the WIA scanner driver. • If you want to crop a portion of a page after pre-scanning the document, you must scan using the scanner glass (also called the flatbed). 1. Load your document. 2.
The machine starts scanning the document.
Home > Scan > Scan from Your Computer (Windows®) > Scan Using Windows® Photo Gallery or Windows® Fax and Scan > WIA Driver Settings (Windows®) WIA Driver Settings (Windows®) Paper source Select the Document Feeder or Flatbed option from the drop-down list. Picture Type (Image Type) Select Color picture, Grayscale picture, Black and white picture or text , or Custom Settings for the type of document you want to scan. To change advanced settings, click the Adjust the quality of the scanned picture link.
Brightness Set the Brightness level by dragging the slider to the right or left to lighten or darken the image. If the scanned image is too light, set a lower brightness level and scan the document again. If the image is too dark, set a higher brightness level and scan the document again. Contrast Increase or decrease the Contrast level by moving the slider to the right or left. An increase emphasizes dark and light areas of the image, while a decrease reveals more details in gray areas.
Home > Scan > Scan from Your Computer (Windows®) > Install BookScan Enhancer and Whiteboard Enhancer (Windows®) Install BookScan Enhancer and Whiteboard Enhancer (Windows®) BookScan Enhancer and Whiteboard Enhancer are image processing applications. BookScan Enhancer can automatically correct images scanned from books. Whiteboard Enhancer can clean up and enhance text and images in photos taken of a whiteboard. These applications are not available for Windows Server® 2003/2008/2012 series.
Home > Scan > Scan from Your Computer (Mac) Scan from Your Computer (Mac) There are several ways you can use your Mac to scan photos and documents on your Brother machine. Use the software applications provided by Brother or your favorite scanning application.
Home > Scan > Scan from Your Computer (Mac) > Scan Using ControlCenter2 (Mac) Scan Using ControlCenter2 (Mac) Use Brother's ControlCenter software to scan photos and save them as JPEGs, PDFs, or other file formats.
Home > Scan > Scan from Your Computer (Mac) > Scan Using ControlCenter2 (Mac) > Scan Using ControlCenter2 (Mac) Scan Using ControlCenter2 (Mac) Send scanned photos or graphics directly to your computer. 1. Load your document. 2. In the Finder menu bar, click Go > Applications > Brother, and then double-click the (ControlCenter) icon. The ControlCenter2 screen appears. 3. Click the SCAN tab. 4. Click the Image button. The scan settings dialog box appears.
5. Change the scan settings, such as file format, file name, destination file path, resolution, or color, if needed. To change the file name or destination file path, click Change. 6. Click the Start Scanning button. The machine starts scanning. The scanned image will open in the application you have selected.
Home > Scan > Scan from Your Computer (Mac) > Scan Using ControlCenter2 (Mac) > Save Scanned Data to a Folder as a PDF File Using ControlCenter2 (Mac) Save Scanned Data to a Folder as a PDF File Using ControlCenter2 (Mac) 1. Load your document. 2. In the Finder menu bar, click Go > Applications > Brother, and then double-click the (ControlCenter) icon. The ControlCenter2 screen appears. 3. Click the SCAN tab. 4. Click the File button. The scan settings dialog box appears.
5. Click the File Type pop-up menu, and then select PDF (*.pdf). To save the document as a password-protected PDF, select Secure PDF (*.pdf) from the File Type pop-up menu, type your password in the Password and Re-type Password fields, and then click OK. 6. Change the scan settings, such as file format, file name, destination folder, resolution, or color, if needed. 7. Click the Start Scanning button. The machine starts scanning. The file will be saved in the folder you selected.
Home > Scan > Scan from Your Computer (Mac) > Scan Using ControlCenter2 (Mac) > Scan Both Sides of an ID Card Using ControlCenter2 (Mac) Scan Both Sides of an ID Card Using ControlCenter2 (Mac) 1. Place an ID card on the scanner glass. 2. In the Finder menu bar, click Go > Applications > Brother, and then double-click the (ControlCenter) icon. The ControlCenter2 screen appears. 3. Click the SCAN tab. 4. Click the File button. The scan settings dialog box appears.
5. Select the ID Card Scan check box. The instruction dialog box appears. 6. Read the instructions on the screen, and then press OK. 7. Configure other settings, if needed. 8. Click the Start Scanning button. The machine starts scanning one side of the identification card. 9. After the machine has scanned one side, turn over the identification card, and then click Continue to scan the other side. 10. Click Finish.
Home > Scan > Scan from Your Computer (Mac) > Scan Using ControlCenter2 (Mac) > Scan to E-mail Attachment Using ControlCenter2 (Mac) Scan to E-mail Attachment Using ControlCenter2 (Mac) Send a scanned document as an email attachment. The Scan to E-mail feature does not support Webmail services. Use the Scan to Image or Scan to File feature to scan a document or a picture, and then attach the scanned file to an email message. 1. Load your document. 2.
5. Change the scan settings, such as file format, file name, destination file path, resolution, or color, if needed. To change the file name or destination file path, click Change. 6. Click the Start Scanning button. The machine starts scanning. Your default email application will open and the scanned image is attached to a new, blank email.
Home > Scan > Scan from Your Computer (Mac) > Scan Using ControlCenter2 (Mac) > Scan to an Editable Text File (OCR) Using ControlCenter2 (Mac) Scan to an Editable Text File (OCR) Using ControlCenter2 (Mac) Your machine can convert characters in a scanned document to text data using optical character recognition (OCR) technology. You can edit this text using your preferred text-editing application. • Mac Presto! PageManager must be installed on your computer. Download Presto! PageManager from nj.newsoft.
5. Change the scan settings, such as file format, file name, destination file path, resolution, or color, if needed. To change the file name or destination file path, click Change. 6. Click the Start Scanning button. The machine scans the document, converts it to editable text, and then sends it to your default word processing application.
Home > Scan > Scan from Your Computer (Mac) > Scan Using ControlCenter2 (Mac) > Scan to an Office File Using ControlCenter2 (Mac) Scan to an Office File Using ControlCenter2 (Mac) Your machine can convert scanned data to a Microsoft® Word file or a Microsoft® PowerPoint® file. In order to use this feature, your Brother machine must be connected to a network that has access to the Internet through either a wired or wireless connection. 1. Load your document. 2.
Home > Scan > Scan from Your Computer (Mac) > Scan Using ControlCenter2 (Mac) > Scan Settings for ControlCenter2 (Mac) Scan Settings for ControlCenter2 (Mac) Settings Applicable Features Image OCR E-mail File Target Application/E-mail Application Yes Yes Yes - File Type Yes Yes Yes Yes File size Yes - Yes Yes OCR Software - Yes - - - Yes - - Destination File Path Yes Yes Yes - File Name Yes Yes Yes Yes Insert Date in File Name Yes Yes Yes Yes Destination Folder
Destination File Path Click the Change button to change the prefix of the file name and the path of the destination folder. File Name Type a prefix for your file name, if needed. To change the prefix for the Image, OCR, and E-mail features, click Change. Insert Date in File Name Automatically inserts the date in the file name of the scanned image. To insert the date in the file name for the Image, OCR and E-mail features, click Change.
• Brightness Set the Brightness level by dragging the slider to the right or left to lighten or darken the image. If the scanned image is too light, set a lower brightness level and scan the document again. If the image is too dark, set a higher brightness level and scan the document again. • Contrast Increase or decrease the Contrast level by moving the slider to the right or left. An increase emphasizes dark and light areas of the image, while a decrease reveals more details in gray areas.
Home > Scan > Scan from Your Computer (Mac) > Scan Using Presto! PageManager or other TWAINCompliant Applications (Mac) Scan Using Presto! PageManager or other TWAIN-Compliant Applications (Mac) • Download Presto! PageManager from nj.newsoft.com.tw/download/brother/ PM9SEInstaller_BR_multilang2.dmg. • Your hard disk drive must have at least 400 MB of free disk space for installation. • Presto! PageManager supports OS X v10.8.5, 10.9.x, 10.10.x.
• After you select a document size, adjust the scanning area by holding down the mouse button and dragging your mouse pointer over the portion you want to scan. 6. Click Start. The machine starts scanning.
Home > Scan > Scan from Your Computer (Mac) > Scan Using Presto! PageManager or other TWAINCompliant Applications (Mac) > TWAIN Driver Settings (Mac) TWAIN Driver Settings (Mac) 1 2 3 4 • Item names and assignable values will vary depending on the machine. • The Brightness setting is available only when selecting Black & White, Gray (Error Diffusion), True Gray, or 24bit Color from the Scan Type options.
3. Document Size Select the exact size of your document from a selection of preset scan sizes. Auto means that the machine will automatically detect the Document Size. • If you select Custom, you can specify the document size. 4. Adjust Image Click the Adjust Image button to adjust other image qualities. Brightness Set the Brightness level by dragging the slider to the right or left to lighten or darken the image.
Related Information • Scan Using Presto! PageManager or other TWAIN-Compliant Applications (Mac) 188
Home > Copy Copy • Copy a Document • Enlarge or Reduce Copied Images • Sort Copies • Make Page Layout Copies ( N in 1 or Poster) • 2-sided Copy • Copy an ID Card • Copy in Ink Save Mode • Copy Options 189
Home > Copy > Copy a Document Copy a Document 1. Make sure you have loaded the correct size paper in the paper tray. 2. Do one of the following: • Place the document face down on the scanner glass. • Place the document face down in the ADF. (ADF models only) (If you are copying multiple pages, we recommend using the ADF.) 3. Press [Copy]. The touchscreen displays: 4. Change the copy settings, if needed.
Option Description (No. of Copies ) Enter the number of copies in one of the following ways: • Press - or + on the touchscreen. • Press to display the keyboard on the touchscreen, and then enter the number of copies using the touchscreen keyboard. Press OK. Options Press to change the copy settings for the next copy only. • When you have finished changing settings, press OK. • After you have finished choosing new options, you can save them by pressing the Save as Shortcut button. 5.
Home > Copy > Enlarge or Reduce Copied Images Enlarge or Reduce Copied Images Select an enlargement or reduction ratio to resize your copied data. 1. Load your document. 2. Press [Copy]. 3. Enter the number of copies in one of the following ways: • Press [-] or [+] on the touchscreen. • Press to display the keyboard on the touchscreen, and then enter the number of copies using the touchscreen keyboard. Press [OK]. 4. Press [Options] > [Enlarge/Reduce]. 5.
Home > Copy > Sort Copies Sort Copies Sort multiple copies. Pages will be stacked in the order they are fed, that is: 1, 2, 3, and so on. 1. Load your document. 2. Press [Copy]. 3. Enter the number of copies in one of the following ways: • Press [-] or [+] on the touchscreen. • Press to display the keyboard on the touchscreen, and then enter the number of copies using the touchscreen keyboard. Press [OK]. 4. Press [Options] > [Stack/Sort] > [Sort]. 5.
Home > Copy > Make Page Layout Copies ( N in 1 or Poster) Make Page Layout Copies ( N in 1 or Poster) The N in 1 copy feature saves paper by copying two or four pages of your document onto one page of the copy. The poster feature divides your document into sections, then enlarges the sections so you can assemble them into a poster. To print a poster, use the scanner glass. • Make sure the paper size is set to Letter, A4, or Executive. • Poster copy is not available for Executive size paper.
Related Information • Copy • Page Layout Options for Copies 195
Home > Copy > Make Page Layout Copies ( N in 1 or Poster) > Page Layout Options for Copies Page Layout Options for Copies • If you are copying from the ADF, insert the document face down in the direction shown in the table. (ADF models only) • If you are copying from the scanner glass, place the document face down in the direction shown in the table.
Option Description Poster(3x3) (Using the scanner glass) Related Information • Make Page Layout Copies ( N in 1 or Poster) 197
Home > Copy > 2-sided Copy 2-sided Copy • Copy on Both Sides of the Paper (1-sided to 2-sided/2-sided to 2-sided) 198
Home > Copy > 2-sided Copy > Copy on Both Sides of the Paper (1-sided to 2-sided/2-sided to 2-sided) Copy on Both Sides of the Paper (1-sided to 2-sided/2-sided to 2-sided) Reduce the amount of paper you use by copying onto both sides of the paper. • We recommend loading single-sided documents in the ADF for 2-sided copying. (ADF models only) • For 2-sided documents use the scanner glass. • You can use only Letter, A4, A5, or Executive size plain paper. 1. Load your document. 2. Press [Copy]. 3.
• If you get a paper jam, press the [Advanced] button, and then press one of the jam prevention settings: [2-sided 1] or [2-sided 2]. • The [2-sided 1] option uses a longer print time for the ink to dry. • The [2-sided 2] option uses a longer print time and will also print in lighter colors.
Home > Copy > Copy an ID Card Copy an ID Card Use the [2in1(ID)] feature to copy both sides of an identification card onto one page, keeping the original card size. • Make sure the paper size is set to Letter or A4. • You may copy an identification card to the extent permitted under applicable laws. For more detailed information, see the Product Safety Guide. 1. Place your identification card face down near the upper-left corner of the scanner glass. a a c d b a. 0.12 in.
5. Read and confirm the displayed list of settings you have selected. When you have finished changing settings, press [OK]. 6. Press [Black Start] or [Color Start]. The machine starts scanning one side of the identification card. 7. After the machine has scanned the first side, turn over the identification card and press [Continue] to scan the other side.
Home > Copy > Copy in Ink Save Mode Copy in Ink Save Mode When you select Ink Save Mode, the machine prints the colors lighter and emphasizes the outlines of the images. • The amount of ink that is saved varies depending on the type of documents printed. • Ink Save Mode may make your printouts look different from your original document. • The Ink Save Mode feature is supported by technology from Reallusion, Inc. 1. Load your document. 2. Press [Copy]. 3.
Home > Copy > Copy Options Copy Options To change copy settings, press the [Options] button. Option Description Quality Select the Copy resolution for your type of document. When you select the Normal or Fast option, Plain Paper is the only Paper Type option. Paper Type Select a paper type. If you are copying on special paper, set the machine for the type of paper you are using to get the best print quality. Paper Size Select a paper size.
Option Description Advanced Settings Ink Save Mode Prints colors lighter and emphasizes the outlines of images. Thin Paper Copy Avoids bleeding through thin paper when copying. Book Copy Corrects dark borders and skew when copying from the scanner glass. Watermark Copy Places text in your document as a watermark. Remove Background Color Removes the document's background color in copies. The white background becomes more apparent. This saves some ink and may make certain copies easier to read.
The Ink Save Mode, Thin Paper Copy, Book Copy and Watermark Copy features are supported by technology from Reallusion, Inc.
Home > Fax Fax • Send a Fax • Receive a Fax • Voice Operations and Fax Numbers • Telephone Services and External Devices • Fax Reports • PC-FAX 207
Home > Fax > Send a Fax Send a Fax • Send a Fax from Your Brother Machine • Send a Fax Manually • Send a Fax at the End of a Conversation • Send the Same Fax to More than One Recipient (Broadcasting) • Send a Fax in Real Time • Send a Fax at a Specified Time (Delayed Fax) • Cancel a Fax in Progress • Check and Cancel a Pending Fax • Fax Polling • Fax Options 208
Home > Fax > Send a Fax > Send a Fax from Your Brother Machine Send a Fax from Your Brother Machine 1. Load your document in the ADF or on the scanner glass. 2. Press [Fax]. If [Fax Preview] is set to [On], press [Fax] > [Sending Faxes]. The touchscreen displays: 3. Enter the fax number in one of the following ways: • Dial Pad (Enter the fax number manually.) Press all digits of the number using the touchscreen. • [Redial] (Redial the last number you dialed.) Press [Call History] > [Redial].
9. Do one of the following: • If you are using the ADF, the machine starts scanning and sending the document. • If you are using the scanner glass and selecting [Black] in the [Color Setting], the machine starts scanning the first page. Go to the next step. • If you are using the scanner glass and selecting [Color] in the [Color Setting], the touchscreen asks if you want to send a color fax. Press [Yes (Color fax)] to confirm. The machine starts dialing and sending the document. 10.
Home > Fax > Send a Fax > Send a Fax Manually Send a Fax Manually Manual fax transmission lets you hear the dialing, ringing and fax-receiving tones while sending a fax. 1. Load your document. 2. Press [Fax]. If [Fax Preview] is set to [On], press [Fax] > [Sending Faxes]. 3. Press [Hook] and listen for a dial tone. 4. Enter the fax number. 5. When you hear fax tones, press [Fax Start]. • If using the scanner glass, press [Send].
Home > Fax > Send a Fax > Send a Fax at the End of a Conversation Send a Fax at the End of a Conversation At the end of a conversation, you can send a fax to the other party before you both hang up. 1. Ask the other party to wait for fax tones (beeps), and then press the Start or Send key before hanging up. 2. Load your document. 3. Press [Fax Start]. • If using the scanner glass, press [Send]. If the touchscreen does not show [Fax Start], press to display it. 4.
Home > Fax > Send a Fax > Send the Same Fax to More than One Recipient (Broadcasting) Send the Same Fax to More than One Recipient (Broadcasting) Use the Broadcasting feature to send the same fax to multiple fax numbers at the same time. • This feature is available only for black and white faxes. • Address Book numbers must be stored in the machine’s memory before they can be used in a broadcast. • Group numbers must also be stored in the machine’s memory before they can be used in a broadcast.
• Enter Text on Your Brother Machine 214
Home > Fax > Send a Fax > Send the Same Fax to More than One Recipient (Broadcasting) > Cancel a Broadcast in Progress Cancel a Broadcast in Progress While broadcasting you can cancel the fax currently being sent or the whole broadcast job. 1. Press . 2. Do one of the following: • To cancel the entire broadcast, press [Entire Broadcast]. Press [Yes] to confirm or press [No] to exit without canceling. • To cancel the current number being dialed, press the name or number on the touchscreen.
Home > Fax > Send a Fax > Send a Fax in Real Time Send a Fax in Real Time When sending a fax, the machine scans the document into the memory before sending it. As soon as the telephone line is free, the machine starts dialing and sending. If you want to send an important document immediately without waiting for the machine to retrieve the scan from its memory, transmit the fax quickly by turning on [Real Time TX].
Home > Fax > Send a Fax > Send a Fax at a Specified Time (Delayed Fax) Send a Fax at a Specified Time (Delayed Fax) You can store up to 50 faxes in the machine's memory to be sent within the next twenty-four hour period. This feature is available only for black and white faxes. 1. Load your document. 2. Press [Fax]. If [Fax Preview] is set to [On], press [Fax] > [Sending Faxes]. 3. Press [Options] > [Delayed Fax]. 4. Press [Delayed Fax]. 5. Press [On]. 6. Press [Set Time]. 7.
Home > Fax > Send a Fax > Cancel a Fax in Progress Cancel a Fax in Progress 1. Press to cancel a fax that is already in process. 2. When you press while the machine is dialing or sending, the touchscreen displays [Cancel Job?]. Press [Yes].
Home > Fax > Send a Fax > Check and Cancel a Pending Fax Check and Cancel a Pending Fax Follow these steps to view or to cancel faxes stored in the machine's memory and waiting to be sent. If there are no fax jobs in memory, the LCD displays [No Jobs Waiting]. You can cancel a fax job before it is sent. 1. Press [Settings] > [All Settings] > [Fax] > [Remaining Jobs]. 2. Do the following for each fax job you want to check or cancel: a. Press a or b to scroll through the waiting jobs.
Home > Fax > Send a Fax > Fax Polling Fax Polling Polling lets you set up your machine so the other party pays for the call when receiving a fax from you. It also lets you pay for the call when you call someone's fax machine to retrieve a fax. The polling feature must be set up on both machines to work. Not all fax machines support polling.
Home > Fax > Send a Fax > Fax Polling > Polled Transmit Polled Transmit Polled transmit lets you set up your machine to wait with a document so another fax machine can call and retrieve it. The document will be stored and can be retrieved by any other fax machine until you delete it from the memory. This feature is available only for black and white faxes.
Home > Fax > Send a Fax > Fax Polling > Polled Transmit > Setup for Polled Transmit Setup for Polled Transmit This feature is available only for black and white faxes. 1. Load your document. 2. Press [Fax]. If [Fax Preview] is set to [On], press [Fax] > [Sending Faxes]. 3. Press [Options] > [Polled TX]. 4. Press [On] (or [Off]). 5. Press [Fax Start]. If you are using the ADF, the machine starts scanning the document. 6.
Home > Fax > Send a Fax > Fax Options Fax Options To change fax-sending settings, press the [Options] button. Option Description Fax Resolution Set the resolution for outgoing faxes. The fax quality often can be improved by changing the Fax Resolution. Contrast Adjust the contrast. If your document is very light or very dark, changing the contrast may improve the fax quality. Broadcasting (black and white only) Send the same fax message to more than one fax number at the same time.
Home > Fax > Receive a Fax Receive a Fax • Receive Mode Settings • Fax Preview • Shrink Page Size of an Oversized Incoming Fax • Set the Fax Receive Stamp • Receive a Fax at the End of a Telephone Conversation • Memory Receive Options • Remote Fax Retrieval • Fax Polling 224
Home > Fax > Receive a Fax > Receive Mode Settings Receive Mode Settings • Receive Modes • Choose the Correct Receive Mode • Set the Number of Rings Before the Machine Answers (Ring Delay) • Set the F/T Ring Time (Pseudo/Double-ring) • Set Easy Receive 225
Home > Fax > Receive a Fax > Receive Mode Settings > Receive Modes Receive Modes Some receive modes answer automatically ([Fax Only] and [Fax/Tel]). You may want to change the Ring Delay before using these modes. Fax Only [Fax Only] mode automatically will answer every call as a fax. Fax/Tel [Fax/Tel] mode helps you manage incoming calls, by recognizing whether they are fax or voice calls and handling them in one of the following ways: • Faxes will be received automatically.
Home > Fax > Receive a Fax > Receive Mode Settings > Choose the Correct Receive Mode Choose the Correct Receive Mode The correct Receive Mode for you is determined by the external devices and telephone subscriber services (Voice Mail, Distinctive Ring and so on) you will be using on the same line as the Brother machine.
Home > Fax > Receive a Fax > Receive Mode Settings > Set the Number of Rings Before the Machine Answers (Ring Delay) Set the Number of Rings Before the Machine Answers (Ring Delay) When somebody calls your machine, you will hear the normal telephone ring sound. The number of rings is set in the Ring Delay option. • The Ring Delay setting sets the number of times the machine rings before it answers in [Fax Only] and [Fax/Tel] modes.
Home > Fax > Receive a Fax > Receive Mode Settings > Set the F/T Ring Time (Pseudo/Double-ring) Set the F/T Ring Time (Pseudo/Double-ring) When you set the Receive Mode to [Fax/Tel], if the call is a fax, your machine will receive it automatically. However, if it is a voice call, the machine will sound the F/T ring (pseudo/double-ring) for the time you set in the F/T Ring Time option. When you hear the F/T ring, it means that a voice caller is on the line.
Home > Fax > Receive a Fax > Receive Mode Settings > Set Easy Receive Set Easy Receive If Easy Receive is On: The machine can receive a fax automatically, even if you answer the call. When the message that your machine is receiving a fax appears on the LCD or when you hear a click on the phone line through the handset you are using, just replace the handset. Your machine will do the rest.
Home > Fax > Receive a Fax > Fax Preview Fax Preview Use the Fax Preview feature to view received faxes on the LCD.
Home > Fax > Receive a Fax > Fax Preview > Set Fax Preview to On Set Fax Preview to On • This feature is available only for black and white faxes. • When Fax Preview is turned on, a backup copy of received faxes will not be printed for Fax Forwarding, PC-Fax Receiving and Forward to Cloud operations, even if you set Backup Print to [On]. • Although printed faxes show the received date and time when Fax Receive Stamp is turned on, the Fax Preview screen will not display the received date and time. 1.
Home > Fax > Receive a Fax > Fax Preview > Preview New Faxes Preview New Faxes When a fax is received, a message appears on the LCD. • This feature is available only for black and white faxes. • To see a fax you already previewed, press [Fax] and [Received Faxes]. 1. Press [View]. 2. The fax list includes old and new faxes. A blue mark appears next to new faxes. Press the fax you want. If you want to print or delete all the faxes in the list, press [Print/Delete].
Button Result Reduce the fax. a or b Scroll vertically. d or c Scroll horizontally. Rotate the fax clockwise. Delete the fax. Press Yes to confirm. Go back to the previous page. Go to the next page. Go back to the fax list. Start Print the fax. If the fax is a single page, it starts printing. A touchscreen message asks if you want to delete the fax from the machine's memory. To delete the fax, press Yes. To keep the fax in the machine's memory, press No.
Home > Fax > Receive a Fax > Shrink Page Size of an Oversized Incoming Fax Shrink Page Size of an Oversized Incoming Fax When the [Auto Reduction] feature is [On], your Brother machine reduces any oversized incoming fax page to fit on your paper. The machine calculates the reduction ratio using the page size of the fax and your Paper Size setting. 1. Press [Settings] > [All Settings] > [Fax] > [Setup Receive] > [Auto Reduction]. 2. Press [On] (or [Off]). 3. Press .
Home > Fax > Receive a Fax > Set the Fax Receive Stamp Set the Fax Receive Stamp Set the machine to print the date and time of receipt at the top of each incoming fax page. Make sure you have set the current date and time on the machine. This feature is available only for black and white faxes. [Settings] > [All Settings] > [Fax] > [Setup Receive] > [Fax Rx Stamp]. 1. Press 2. Press [On] (or [Off]). 3. Press .
Home > Fax > Receive a Fax > Receive a Fax at the End of a Telephone Conversation Receive a Fax at the End of a Telephone Conversation If you are speaking on the telephone connected to your Brother machine and the other party is also speaking on a telephone connected to his fax machine, at the end of the conversation, the other party can send you a fax before you both hang up. • Your machine's ADF must be empty. 1. Ask the other party to load the fax and to press the Start or Send key. 2.
Home > Fax > Receive a Fax > Memory Receive Options Memory Receive Options Use Memory Receive options to direct incoming faxes while you are away from the machine. You can use only one Memory Receive option at a time. Memory Receive can be set to: • Fax Forwarding • Paging (USA and Canada only) • Fax Storage • PC-Fax Receive • Forward to Cloud The machine forwards your received faxes to the online services. For more detailed information, see the Web Connect Guide.
Home > Fax > Receive a Fax > Memory Receive Options > Forward Incoming Faxes to Another Machine Forward Incoming Faxes to Another Machine Use the Fax Forwarding feature to automatically forward your incoming faxes to another machine. This feature is available only for black and white faxes. [Settings] > [All Settings] > [Fax] > [Setup Receive] > [Memory Receive]. 1. Press 2. Press a or b to display the [Fax Forward] option, and then press it. 3.
Home > Fax > Receive a Fax > Memory Receive Options > Set the Machine to Dial a Cell Phone or Pager Number When Receiving Faxes Set the Machine to Dial a Cell Phone or Pager Number When Receiving Faxes Use the Paging option if you want your machine to dial a pre-programed cell phone or pager number. This feature activates your cell phone or pager so you will know there is a fax message in the machine’s memory. • This feature is available only for black and white faxes.
Home > Fax > Receive a Fax > Memory Receive Options > Store Incoming Faxes in the Machine's Memory Store Incoming Faxes in the Machine's Memory Use the Fax Storage feature to store incoming faxes in the machine's memory. Retrieve your stored fax messages from a fax machine at another location using the Remote Retrieval commands. Your machine prints a backup copy of each stored fax. • This feature is available only for black and white faxes. 1.
Home > Fax > Receive a Fax > Memory Receive Options > Use PC-Fax Receive to Transfer Received Faxes to Your Computer (Windows® only) Use PC-Fax Receive to Transfer Received Faxes to Your Computer (Windows® only) Turn on the PC-Fax Receive feature, automatically store incoming faxes to your machine's memory, and then send them to your computer. Use your computer to view and store these faxes. • This feature is available only for black and white faxes.
Home > Fax > Receive a Fax > Memory Receive Options > Change Memory Receive Options Change Memory Receive Options If there are faxes in your machine's memory when you change any Memory Receive option, the LCD displays one of the following questions: • • • If received faxes have already been printed, the touchscreen displays [Erase all faxes?] - If you press [Yes], faxes in the memory will be erased before the setting changes.
Home > Fax > Receive a Fax > Memory Receive Options > Turn Off Memory Receive Turn Off Memory Receive Turn off Memory Receive if you do not want the machine to save or transfer incoming faxes. 1. Press [Settings] > [All Settings] > [Fax] > [Setup Receive] > [Memory Receive]. 2. Press [Off]. The touchscreen displays [Print all faxes?] or [Erase all faxes?] if received faxes are in your machine's memory. 3. Press .
Home > Fax > Receive a Fax > Memory Receive Options > Print a Fax Stored in the Machine's Memory Print a Fax Stored in the Machine's Memory • This feature is available only for black and white faxes. • After you print the fax, it is erased from the machine's memory. If you select [Paging] (USA and Canada only) or [Fax Storage], you can print all faxes from the memory. 1. Press [Settings] > [All Settings] > [Fax] > [Print Fax].
Home > Fax > Receive a Fax > Remote Fax Retrieval Remote Fax Retrieval Use Remote Retrieval to call your machine from any touch-tone telephone or fax machine, and use a remote access code and remote commands to retrieve fax messages.
Home > Fax > Receive a Fax > Remote Fax Retrieval > Set a Remote Access Code Set a Remote Access Code Set a Remote Access Code to access and control your Brother machine even when you are away from it. 1. Press [Settings] > [All Settings] > [Fax] > [Remote Access]. 2. Enter a three-digit code using the numbers [0] through [9], [*], or [#] using the touchscreen (The preset '*' cannot be changed). Press [OK]. • DO NOT use the same code used for Fax Receive Code (*51) or Telephone Answer Code (#51).
Home > Fax > Receive a Fax > Remote Fax Retrieval > Use Your Remote Access Code Use Your Remote Access Code 1. When away from your Brother machine, dial your fax number from a touch-tone telephone or fax machine. 2. When your machine answers, immediately enter your three-digit Remote Access Code, followed by *. 3. Your Brother machine signals if it has received faxes: • One long beep - the machine received at least one fax • No beeps - the machine has not received a fax 4.
Home > Fax > Receive a Fax > Remote Fax Retrieval > Remote Retrieval Commands Remote Retrieval Commands Use the Remote Commands in this table to access fax commands and options when you are away from your Brother machine. When you call the machine and enter your remote access code (three digits followed by *), the system will sound two short beeps and you must enter a Remote Command (column 1), followed by one of the options (column 2) for that command.
Home > Fax > Receive a Fax > Remote Fax Retrieval > Forward Faxes Remotely Forward Faxes Remotely Call your Brother machine from any touch-tone telephone or fax machine to forward incoming faxes to another machine. • You must turn on Fax Storage, Paging (USA and Canada only), or Fax Preview before you use this feature. 1. Dial your fax number. 2. When your machine answers, enter your Remote Access Code (three digits followed by *). If you hear one long beep, you have messages. 3.
Home > Fax > Receive a Fax > Remote Fax Retrieval > Change the Fax Forwarding Number Change the Fax Forwarding Number 1. Dial your fax number. 2. When your machine answers, enter your Remote Access Code (three digits followed by *). If you hear one long beep, you have messages. 3. When you hear two short beeps, press 9 5 4. 4. Wait for the long beep, enter the new number (up to 20 digits) of the remote fax machine you want your fax messages forwarded to using the dial pad, then enter # #.
Home > Fax > Receive a Fax > Fax Polling Fax Polling Polling lets you set up your machine so the other party pays for the call when receiving a fax from you. It also lets you pay for the call when you call someone's fax machine to retrieve a fax. The polling feature must be set up on both machines to work. Not all fax machines support polling.
Home > Fax > Receive a Fax > Fax Polling > Polling Receive Polling Receive Polling Receive lets you call another fax machine to receive a fax.
Home > Fax > Receive a Fax > Fax Polling > Polling Receive > Setup for Polling Receive Setup for Polling Receive 1. Press [Fax]. If [Fax Preview] is set to [On], press [Fax] > [Sending Faxes]. 2. Press [Options] > [Polling RX]. 3. Press [On] (or [Off]). 4. Enter the fax number you are polling using the Address Book or keyboard. 5. Press [Fax Start].
Home > Fax > Receive a Fax > Fax Polling > Polling Receive > Setup for Sequential Polling Receive Setup for Sequential Polling Receive Sequential Polling Receive lets you request documents from several fax machines in one operation. Afterwards, a Sequential Polling Report will be printed. This feature is available only for black and white faxes. 1. Press [Fax]. If [Fax Preview] is set to [On], press [Fax] > [Sending Faxes]. 2. Press [Options] > [Polling RX]. 3. Press [On] (or [Off]). 4.
Home > Fax > Receive a Fax > Fax Polling > Polling Receive > Cancel a Sequential Polling Job Cancel a Sequential Polling Job 1. Press . 2. Do one of the following: • To cancel the entire sequential polling job, press [Entire Seq. Poll]. Press [Yes] to confirm or press [No] to exit without canceling. • To cancel the current number being dialed, press the name or number on the touchscreen. Press [Yes] to confirm or press [No] to exit without canceling. • To exit without canceling, press .
Home > Fax > Receive a Fax > Fax Polling > Polling Receive > Stop Polling Stop Polling To cancel the polling process, press while the machine is dialing.
Home > Fax > Voice Operations and Fax Numbers Voice Operations and Fax Numbers • Voice Operations • Store Fax Numbers • Set up Groups for Broadcasting • Dial Access Codes and Credit Card Numbers 258
Home > Fax > Voice Operations and Fax Numbers > Voice Operations Voice Operations • Send Tone Signals • Pick up a Voice Call in Fax/Tel Receive Mode • Special Line Considerations 259
Home > Fax > Voice Operations and Fax Numbers > Voice Operations > Send Tone Signals Send Tone Signals If you have a Pulse dialing service, but must send Tone signals (for example, for telephone banking), follow these steps. If you have a Touch Tone service, you will not need this feature to send tone signals. This feature is available only in Canada. 1. Press [Fax]. If [Fax Preview] is set to [On], press [Fax] > [Sending Faxes]. 2. Press [Hook]. 3. Press # on the machine's Touchpanel.
Home > Fax > Voice Operations and Fax Numbers > Voice Operations > Pick up a Voice Call in Fax/Tel Receive Mode Pick up a Voice Call in Fax/Tel Receive Mode When the machine is in Fax/Tel mode, it will use the F/T Ring (pseudo/double-ringing) to alert you to pick up a voice call. If you are at the machine, lift the external telephone’s handset, and then press Hook button or [Pickup] button to answer.
Home > Fax > Voice Operations and Fax Numbers > Voice Operations > Special Line Considerations Special Line Considerations • Rollover Telephone Lines • Two-Line Telephone System • Convert Telephone Wall Outlets • Install Your Brother Machine, an External Two-Line TAD and Two-Line Telephone 262
Home > Fax > Voice Operations and Fax Numbers > Voice Operations > Special Line Considerations > Rollover Telephone Lines Rollover Telephone Lines A rollover telephone system is a group of two or more separate telephone lines that pass incoming calls to each other if they are busy. This feature is available only in the USA and Canada. The calls are usually passed down or 'rolled over' to the next available telephone line in a preset order.
Home > Fax > Voice Operations and Fax Numbers > Voice Operations > Special Line Considerations > Two-Line Telephone System Two-Line Telephone System A two-line telephone system is nothing more than two separate telephone numbers on the same wall outlet. This feature is available only in the USA and Canada. The two telephone numbers can be on separate jacks (RJ11) or combined into one jack (RJ14). Your machine must be plugged into an RJ11 jack.
Home > Fax > Voice Operations and Fax Numbers > Voice Operations > Special Line Considerations > Convert Telephone Wall Outlets Convert Telephone Wall Outlets This feature is available only in the USA and Canada. There are three ways to convert to an RJ11 jack. The first two ways may require assistance from the telephone company. You can change the wall outlets from one RJ14 jack to two RJ11 jacks. Or, you can have an RJ11 wall outlet installed and slave or jump one of the telephone numbers to it.
Home > Fax > Voice Operations and Fax Numbers > Voice Operations > Special Line Considerations > Install Your Brother Machine, an External Two-Line TAD and Two-Line Telephone Install Your Brother Machine, an External Two-Line TAD and Two-Line Telephone When you are installing an external two-line telephone answering device (TAD) and a two-line telephone, your machine must be isolated on one line at both the wall jack and at the TAD. • This feature is available only in the USA and Canada.
Home > Fax > Voice Operations and Fax Numbers > Store Fax Numbers Store Fax Numbers • Store Address Book Numbers • Store Address Book Numbers from Outgoing Calls • Store Address Book Numbers from Caller ID History • Change or Delete Address Book Names or Numbers 267
Home > Fax > Voice Operations and Fax Numbers > Store Fax Numbers > Store Address Book Numbers Store Address Book Numbers You can store up to 100 Addresses with a name, and each name can have two numbers. [Fax] > [Address Book]. 1. Press 2. Do the following steps: a. Press [Edit] > [Add New Address] > [Name]. b. Enter the name (up to 16 characters) using the touchscreen. Press [OK]. c. Press [Address 1]. d. Enter the first fax or telephone number (up to 20 digits) using the touchscreen. Press [OK].
Home > Fax > Voice Operations and Fax Numbers > Store Fax Numbers > Store Address Book Numbers from Outgoing Calls Store Address Book Numbers from Outgoing Calls You can store Address Book numbers from the Outgoing Call history. 1. Press [Fax] > [Call History] > [Outgoing Call]. 2. Press a or b to display the number you want to store, and then press it. 3. Press [Edit] > [Add to Address Book] > [Name]. To delete the number from the Outgoing Call history list, press [Edit] > [Delete].
Home > Fax > Voice Operations and Fax Numbers > Store Fax Numbers > Store Address Book Numbers from Caller ID History Store Address Book Numbers from Caller ID History If you have Caller ID subscriber service from your telephone company, you can store Address Book numbers from incoming calls in the Caller ID history. 1. Press [Fax] > [Call History] > [Caller ID history]. 2. Press a or b to display the name or number you want to store, and then press it. 3. Press [Edit] > [Add to Address Book] > [Name].
Home > Fax > Voice Operations and Fax Numbers > Store Fax Numbers > Change or Delete Address Book Names or Numbers Change or Delete Address Book Names or Numbers You can change or delete an Address Book name or number that has already been stored. 1. Press [Fax] > [Address Book] > [Edit]. 2. Press a or b to display [Change], and then press it. To delete numbers, press a or b to display [Delete], and then press it.
Home > Fax > Voice Operations and Fax Numbers > Set up Groups for Broadcasting Set up Groups for Broadcasting A Group, which can be stored in the Address Book, allows you to send the same fax message to many fax numbers. First, you must store each fax number in the Address Book. Then you can include them as numbers in the Group. Each Group uses up an Address Book number. You can store up to six Groups. 1. Press [Fax] > [Address Book]. 2. Do the following steps: a. Press [Edit] > [Setup Groups] > [Name].
Home > Fax > Voice Operations and Fax Numbers > Set up Groups for Broadcasting > Change a Group Name Change a Group Name 1. Press [Fax] > [Address Book] > [Edit] > [Change]. 2. Press a or b to display the Group you want to change, and then press it. 3. Press [Name]. 4. Enter the new Group name (up to 16 characters) using the touchscreen. Press [OK]. How to change the stored name: To change a character, press d or c to position the cursor to highlight the incorrect character, and then press .
Home > Fax > Voice Operations and Fax Numbers > Set up Groups for Broadcasting > Delete a Group Delete a Group 1. Press [Fax] > [Address Book] > [Edit] > [Delete]. 2. Press a or b to display the Group you want to delete, and then press it. 3. Press [OK]. 4. When the touchscreen displays [Erase this data?], press [Yes]. 5. Press .
Home > Fax > Voice Operations and Fax Numbers > Set up Groups for Broadcasting > Add or Delete Group Members Add or Delete Group Members 1. Press [Fax] > [Address Book] > [Edit] > [Change]. 2. Press a or b to display the Group you want to change, and then press it. 3. Press a or b to display [Add/Delete], and then press it. 4. Press a or b to display the number you want to add or delete. 5.
Home > Fax > Voice Operations and Fax Numbers > Dial Access Codes and Credit Card Numbers Dial Access Codes and Credit Card Numbers Sometimes you may want to choose from several long-distance carriers when you send a fax. Rates may vary depending on the time and destination. To take advantage of low rates, you can store the access codes of longdistance carriers and credit card numbers as Address Book numbers.
Home > Fax > Telephone Services and External Devices Telephone Services and External Devices • Voice Mail • Distinctive Ring • Caller ID • Voice Over Internet Protocol (VoIP/Telephone Line Interference) • External TAD (Telephone Answering Device) • External and Extension Telephones 277
Home > Fax > Telephone Services and External Devices > Voice Mail Voice Mail This feature is available only in the USA and Canada. If you have Voice Mail on the same telephone line as your Brother machine, Voice Mail and the Brother machine will conflict with each other when receiving incoming calls. For example, if your Voice Mail is set to answer after four rings and your Brother machine is set to answer after two rings, then your Brother machine will answer first.
Home > Fax > Telephone Services and External Devices > Distinctive Ring Distinctive Ring This feature is available only in the USA and Canada. Distinctive Ring is a function of your Brother machine that allows a person with one line to receive fax and voice calls through two different phone numbers on that one line. Brother uses the term "Distinctive Ring," but telephone companies market the service under a variety of names, such as Smart Ring, Ring Master or Ident-aRing.
Ring Pattern 4 Rings very long (normal pattern) • Ring Pattern #1 is often called Short-Short and is the most commonly used. • If the ring pattern you received is not on this chart, contact your telephone company and ask for one that is shown. • The machine will answer only calls to its registered number. • The first two rings are silent on the machine. This is because the fax must <> to the ring pattern (to compare it to the pattern that was ‘registered’).
Home > Fax > Telephone Services and External Devices > Distinctive Ring > Register the Distinctive Ring Pattern Register the Distinctive Ring Pattern This feature is available only in the USA and Canada. After you set the Distinctive Ring feature to [On], your Distinctive Ring number will receive faxes automatically. The receive mode is set to [Manual] automatically and you cannot change it to another receive mode while Distinctive Ring is set to [On].
Home > Fax > Telephone Services and External Devices > Distinctive Ring > Turn off Distinctive Ring Turn off Distinctive Ring This feature is available only in the USA and Canada. [Settings] > [All Settings] > [Fax] > [Miscellaneous] > [Distinctive] > 1. Press [Distinctive]. 2. Press [Off]. 3. Press . When you turn off Distinctive Ring, the machine will stay in [Manual] mode. You must set the Receive Mode again.
Home > Fax > Telephone Services and External Devices > Caller ID Caller ID The Caller ID feature lets you use the Caller ID subscriber service offered by many local telephone companies. This service displays the telephone number, or name if it is available, of your caller as the line rings. • The [# Unavailable] message means the call originated outside your Caller ID service area. • The [Private Call] message means the caller has intentionally blocked transmission of Caller ID information.
Home > Fax > Telephone Services and External Devices > Caller ID > Set up Your Area Code Set up Your Area Code When returning calls from the Caller ID history, your machine will dial "1" plus the area code. If your local dialing plan requires that the "1" not be used for calls within your area code, enter your area code in this setting. This feature is available only in the USA.
Home > Fax > Telephone Services and External Devices > Voice Over Internet Protocol (VoIP/Telephone Line Interference) Voice Over Internet Protocol (VoIP/Telephone Line Interference) VoIP is a type of phone system that uses an Internet connection instead of a traditional telephone line. Telephone providers frequently bundle VoIP together with Internet and cable services. Your machine may not work with some VoIP systems.
Home > Fax > Telephone Services and External Devices > External TAD (Telephone Answering Device) External TAD (Telephone Answering Device) You can connect an external Telephone Answering Device (TAD) to the same line as your machine. When the TAD answers a call, your machine will “listen” for the CNG (fax calling) tones sent by a sending fax machine. If it hears them it will take over the call and receive the fax.
Home > Fax > Telephone Services and External Devices > External TAD (Telephone Answering Device) > Connect an External TAD Connect an External TAD The external TAD must be plugged into the jack labeled EXT. Your machine cannot work correctly if you plug the TAD into a wall jack (unless you are using Distinctive Ring). 1. Plug the telephone line cord from the telephone wall jack into the jack labeled LINE. 2. Remove the protective cap (1) from the jack labeled EXT.
Home > Fax > Telephone Services and External Devices > External TAD (Telephone Answering Device) > Record an Outgoing Message (OGM) on the External TAD Record an Outgoing Message (OGM) on the External TAD 1. Record five seconds of silence at the beginning of your message. This allows your machine time to listen for fax tones. We recommend beginning your OGM with an initial five second silence because the machine cannot hear fax tones over a loud voice.
Home > Fax > Telephone Services and External Devices > External TAD (Telephone Answering Device) > Multi-line Connections (PBX) Multi-line Connections (PBX) We suggest you ask the company that installed your PBX to connect your machine. If you have a multi line system we suggest you ask the installer to connect the unit to the last line on the system. This prevents the machine being activated each time the system receives telephone calls.
Home > Fax > Telephone Services and External Devices > External and Extension Telephones External and Extension Telephones • Connect an External or Extension Telephone • Operation from External and Extension Telephones • Use a Non-Brother Cordless External Handset • Use the Remote Codes 290
Home > Fax > Telephone Services and External Devices > External and Extension Telephones > Connect an External or Extension Telephone Connect an External or Extension Telephone You can connect a separate telephone to your machine as shown in the diagram below. Connect the telephone line cord to the jack labeled EXT. Before you connect an external telephone, remove the protective cap (3) from the EXT. jack on the machine.
Home > Fax > Telephone Services and External Devices > External and Extension Telephones > Operation from External and Extension Telephones Operation from External and Extension Telephones Use extension telephones If you answer a fax call at an extension telephone, you can make your machine receive the fax by pressing the Fax Receive Code *51.
Home > Fax > Telephone Services and External Devices > External and Extension Telephones > Use a Non-Brother Cordless External Handset Use a Non-Brother Cordless External Handset If your non-Brother cordless telephone is connected to the EXT. jack of the machine and you typically carry the cordless handset elsewhere, it is easier to answer calls during the Ring Delay.
Home > Fax > Telephone Services and External Devices > External and Extension Telephones > Use the Remote Codes Use the Remote Codes Fax Receive Code If you answer a fax call on an extension telephone, you can tell your machine to receive it by pressing the Fax Receive Code *51. Wait for the chirping sounds then replace the handset. If you answer a fax call at the external telephone, you can make the machine receive the fax by pressing the Start button and then selecting the option to receive.
Home > Fax > Telephone Services and External Devices > External and Extension Telephones > Use the Remote Codes > Change the Remote Codes Change the Remote Codes The preset Fax Receive Code is *51. The preset Telephone Answer Code is #51. If you are always disconnected when accessing your External TAD remotely, try changing the three-digit remote codes, for example to ### and 999. 1. Press [Settings] > [All Settings] > [Fax] > [Setup Receive] > [Remote Codes]. 2.
Home > Fax > Fax Reports Fax Reports • Set the Transmission Verification Report's Style • Set the Fax Journal's Interval Period • Print Reports • Set the Machine to Power Off Automatically 296
Home > Fax > Fax Reports > Set the Transmission Verification Report's Style Set the Transmission Verification Report's Style You can use the Transmission Verification Report as proof that you sent a fax. This report lists the receiving party's name or fax number, the time and date of transmission, duration of transmission, number of pages sent, and whether or not the transmission was successful.
Home > Fax > Fax Reports > Set the Fax Journal's Interval Period Set the Fax Journal's Interval Period You can set the machine to print a Fax Journal at specific intervals (every 50 faxes, 6, 12 or 24 hours, 2 or 7 days). 1. Press [Settings] > [All Settings] > [Fax] > [Report Setting] > [Journal Period]. 2. Press [Journal Period]. 3. Press a or b to select an interval.
Home > Fax > PC-FAX PC-FAX • PC-FAX for Windows® • PC-FAX for Mac 299
Home > Fax > PC-FAX > PC-FAX for Windows® PC-FAX for Windows® • PC-FAX Overview (Windows®) • Send a Fax Using PC-FAX (Windows®) • Receive Faxes on Your Computer (Windows®) 300
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) PC-FAX Overview (Windows®) Reduce paper consumption and save time by using Brother's PC-FAX software to send faxes directly from your machine.
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) > Configure PC-FAX (Windows®) Configure PC-FAX (Windows®) Before sending faxes using PC-FAX, personalize the send options in each tab of the PC-FAX Setup dialog box. 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 Click (Start) > All Programs > Brother > Brother Utilities. Click the drop-down list and select your model name (if not already selected).
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) > Configure your PC-Fax Address Book (Windows®) Configure your PC-Fax Address Book (Windows®) Add, edit and delete members and groups to personalize your Brother Address Book.
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) > Configure your PC-Fax Address Book (Windows®) > Add a Member to the Address Book (Windows®) Add a Member to the Address Book (Windows®) Add new people and their fax information to the PC-Fax Address Book if you want to send a fax using Brother PC-Fax software. 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 Click (Start) > All Programs > Brother > Brother Utilities.
3. Type the member's information in the corresponding fields. Only the Name field is required. 4. Click OK.
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) > Configure your PC-Fax Address Book (Windows®) > Create a Group in the Address Book (Windows®) Create a Group in the Address Book (Windows®) Create a group to broadcast the same PC-FAX to several recipients at one time. 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 (Start) > All Programs > Brother > Brother Utilities. Click Click the drop-down list and select your model name (if not already selected).
3. Type the name of the new group in the Group Name field. 4. In the Available Names field, select each name you want to include in the group, and then click Add >>. Members added to the group appear in the Group Members box. 5. When finished, click OK. Each group can contain up to 50 members.
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) > Configure your PC-Fax Address Book (Windows®) > Edit Member or Group Information (Windows®) Edit Member or Group Information (Windows®) 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 Click (Start) > All Programs > Brother > Brother Utilities. Click the drop-down list and select your model name (if not already selected). Click PC-FAX in the left navigation bar, and then click Address Book (Send).
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) > Configure your PC-Fax Address Book (Windows®) > Delete a Member or Group (Windows®) Delete a Member or Group (Windows®) 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 Click (Start) > All Programs > Brother > Brother Utilities. Click the drop-down list and select your model name (if not already selected). Click PC-FAX in the left navigation bar, and then click Address Book (Send).
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) > Configure your PC-Fax Address Book (Windows®) > Export the Address Book (Windows®) Export the Address Book (Windows®) You can export the Address Book as an ASCII text file (*.csv), a vCard (an electronic business card), or Remote Setup Dial Data and save it on your computer. • You cannot export the group settings when you export the Address Book data. 1.
Select and add the items in the order you want them listed. 5. If you are exporting to an ASCII file, under the Divide Character section, select the Tab or Comma option to separate the data fields. 6. Click OK. 7. Browse to the folder on your computer where you want to save the data, type the file name, and then click Save.
Home > Fax > PC-FAX > PC-FAX for Windows® > PC-FAX Overview (Windows®) > Configure your PC-Fax Address Book (Windows®) > Import Information to the Address Book (Windows®) Import Information to the Address Book (Windows®) You can import ASCII text files (*.csv), vCards (electronic business cards), or Remote Setup Dial Data into your Address Book. 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 Click (Start) > All Programs > Brother > Brother Utilities.
You must select and add fields from the Available Items list in the same order they are listed in the import text file. 5. If you are importing an ASCII file, under the Divide Character section, select the Tab or Comma option to separate the data fields. 6. Click OK. 7. Browse to the folder where you want to import the data, type the file name, and then click Open.
Home > Fax > PC-FAX > PC-FAX for Windows® > Send a Fax Using PC-FAX (Windows®) Send a Fax Using PC-FAX (Windows®) PC-FAX supports only black and white faxes. A black and white fax will be sent even if the original data is color and the receiving fax machine supports color faxes. 1. Create a file in any application on your computer. 2. Select the print command in your application. 3. Select Brother PC-FAX as your printer, and then complete your print operation. The Brother PC-FAX dialog box appears. 4.
Home > Fax > PC-FAX > PC-FAX for Windows® > Receive Faxes on Your Computer (Windows®) Receive Faxes on Your Computer (Windows®) Use Brother's PC-FAX software to receive faxes on your computer, screen them and print only those faxes you want.
Home > Fax > PC-FAX > PC-FAX for Windows® > Receive Faxes on Your Computer (Windows®) > Receive Faxes Using PC-FAX Receive (Windows®) Receive Faxes Using PC-FAX Receive (Windows®) Brother's PC-FAX Receive software lets you view and store faxes on your computer. It is automatically installed when you install the Brother software and drivers and works on locally- or network-connected machines. • PC-FAX Receive supports only black and white faxes.
Home > Fax > PC-FAX > PC-FAX for Windows® > Receive Faxes on Your Computer (Windows®) > Receive Faxes Using PC-FAX Receive (Windows®) > Run Brother's PC-FAX Receive on Your Computer (Windows®) Run Brother's PC-FAX Receive on Your Computer (Windows®) We recommend selecting the Start PC-FAX Receive on computer startup check box so that the software runs automatically and can transfer any faxes upon computer startup. 1.
Home > Fax > PC-FAX > PC-FAX for Windows® > Receive Faxes on Your Computer (Windows®) > Receive Faxes Using PC-FAX Receive (Windows®) > Run Brother's PC-FAX Receive on Your Computer (Windows®) > Set Up Your Computer for PC-FAX Receiving (Windows®) Set Up Your Computer for PC-FAX Receiving (Windows®) 1. Double-click the (PC-FAX Receive) icon in your computer task tray. The PC-FAX Receive window appears. 2. Click Settings. 3.
Home > Fax > PC-FAX > PC-FAX for Windows® > Receive Faxes on Your Computer (Windows®) > Receive Faxes Using PC-FAX Receive (Windows®) > Run Brother's PC-FAX Receive on Your Computer (Windows®) > Add Your Brother Machine to PC-FAX Receiving (Windows®) Add Your Brother Machine to PC-FAX Receiving (Windows®) • If you installed the machine following the instructions for a network user, then the machine should already be configured for your network. 1.
5. To change the computer name that will appear on the machine's LCD, type the new name in the Enter your PC display name (Max 15 Characters) field. 6. Click OK.
Home > Fax > PC-FAX > PC-FAX for Windows® > Receive Faxes on Your Computer (Windows®) > Receive Faxes Using PC-FAX Receive (Windows®) > View Received Messages (Windows®) View Received Messages (Windows®) Receiving Status Icon Indicated Status Standby mode No unread messages Receiving messages Messages received Unread messages 1. Double-click the (PC-FAX Receive) icon in your computer task tray. The PC-FAX Receive window appears. 2. Click any faxes in the list to view them. 3.
Even after closing the window, PC-FAX Receive is active and the (PC-FAX Receive ) icon will remain in your computer task tray. To close PC-FAX Receive, click the icon in the computer task tray and click Close.
Home > Fax > PC-FAX > PC-FAX for Mac PC-FAX for Mac Use Brother's PC-FAX software to send faxes directly from your Mac without printing them. This feature helps reduce your paper consumption and save time.
Home > Fax > PC-FAX > PC-FAX for Mac > Send Faxes from Your Application (Mac) Send Faxes from Your Application (Mac) PC-FAX supports only black and white faxes. A black and white fax will be sent even if the original data is color and the receiving fax machine supports color faxes. 1. Create a document in a Mac application. 2. From an application, such as Apple TextEdit, click the File menu, and then select Print. 3. Click the application pop-up menu, and then select the Send Fax option. 4.
To send a fax to more than one number, click the Add button after entering the first fax number and type the next fax number. The destination fax numbers will be listed in the Destination Fax Numbers field. 6. Click Print to send the fax.
Home > PhotoCapture Center PhotoCapture Center • Print Photos Directly from Media • Copy Photos from Media to a Computer • Print Photos from ControlCenter4 (Windows®) 326
Home > PhotoCapture Center > Print Photos Directly from Media Print Photos Directly from Media When your machine is not connected to your computer, you can print photos directly from digital camera media or a USB Flash memory drive, scan documents and save them directly to a memory card or USB flash drive. When your machine is connected to a computer, you can use your computer to access a memory card or USB flash drive inserted in the front of the machine.
Home > PhotoCapture Center > Print Photos Directly from Media > Compatible Memory Cards and USB Flash Drives Compatible Memory Cards and USB Flash Drives Your Brother machine has media drives (slots) for use with common data storage and digital camera media. IMPORTANT The USB direct interface supports only USB flash drives, PictBridge-compatible cameras and digital cameras that use the USB mass storage standard. Other USB devices are not supported.
Home > PhotoCapture Center > Print Photos Directly from Media > Important Information about PhotoCapture Center Important Information about PhotoCapture Center USB flash drives are available only for certain models. Your machine is designed to be compatible with modern digital camera image files, memory cards and USB flash drives. Read the points below to avoid errors: • The image file extension must be .JPG (other image file extensions like .JPEG, .TIF, .GIF and so on will not be recognized).
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine Print Photos from Media Using the Photo Button on the Brother Machine • Preview and Print Photos and Movie Files from Media • Print a Photo Index Sheet (Thumbnails) from Media • Print Photos by Image Number • Enhance Photos Using Advanced Editing Options • Print Photos with Custom Cropping • Print ID Photos • Print Photos from Media in Digital Print Order Format (DPOF) • Pri
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Preview and Print Photos and Movie Files from Media Preview and Print Photos and Movie Files from Media Preview your photos on the LCD before you print them. Print images from movie files that are stored on a memory card or USB flash drive. • If your photos are large files, there may be a delay before each photo is displayed.
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print a Photo Index Sheet (Thumbnails) from Media Print a Photo Index Sheet (Thumbnails) from Media Print a photo Index Sheet to see small preview versions of all pictures on your memory card or USB flash drive. • The PhotoCapture Center assigns numbers for images (such as No.1, No.2, No.3, and so on).
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print Photos by Image Number Print Photos by Image Number Before you can print an individual image, you must print the photo Index Sheet (thumbnails) to know the image number. 1. Open the media slot cover. 2. Put the memory card or USB flash drive in the correct slot. 3. Press [Photo] > [Index Print] > [Print Photos]. 4.
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Enhance Photos Using Advanced Editing Options Enhance Photos Using Advanced Editing Options Edit and add effects to your photos and view them on the LCD before printing. The Enhance Photos feature is supported by technology from Reallusion, Inc. 1. Open the media slot cover. 2. Put the memory card or USB flash drive in the correct slot. 3.
Option Description Sepia Convert the color of your photo to sepia. Auto Correct & Remove Red-Eye The machine decides the appropriate effects for your photo and attempts to remove red-eye. • There are some cases when red-eye may not be removed. - When the face is too small in the image. - When the face is turning too far up, down, left, or right. • Press [Cancel] to return to the list of effects.
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print Photos with Custom Cropping Print Photos with Custom Cropping Crop your photos and view them on the LCD before printing. The Crop Photos feature is supported by technology from Reallusion, Inc. 1. Open the media slot cover. 2. Put the memory card or USB flash drive in the correct slot. 3. Press [Photo] > [Enhance Photos].
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print ID Photos Print ID Photos Select a photo stored in a memory card or USB flash drive and print ID photos for your resume, passport and so on. You can print four ID photos on one sheet of paper, and crop large images to preset sizes. Only one photo will be printed when you select the [2x2inch] or [50x70mm (2x2.
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print Photos from Media in Digital Print Order Format (DPOF) Print Photos from Media in Digital Print Order Format (DPOF) Major digital camera manufacturers (Canon, Inc., Eastman Kodak Company, FUJIFILM Corporation, Panasonic Corporation and Sony Corporation) created this standard to make it easier to print images from a digital camera.
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print Photos with Auto Cropping Print Photos with Auto Cropping If your photo is too long or too wide to fit the space in your layout, part of the image will be cropped. • The factory setting is On. To print the whole image, change this setting to Off. • If you set the [Cropping] setting to Off, set the [Borderless] setting to Off, also. Cropping: On Cropping: Off 1.
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print Borderless Photos from Media Print Borderless Photos from Media This feature expands the printable area to the edges of the paper. Printing time will be slower. 1. Open the media slot cover. 2. Put the memory card or USB flash drive in the correct slot. 3. Press [Photo] > [View Photos]. 4. Press d or c to display each photo.
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print the Date from Your Photo's Data Print the Date from Your Photo's Data Print the date if it is already in your photo’s information. The date will be printed on the lower-right corner. To use this setting, the photo must include the date. The Digital Print Order Format (DPOF) setting on your camera must be turned off to use the Print Date feature. 1.
Home > PhotoCapture Center > Print Photos Directly from Media > Print Photos from Media Using the Photo Button on the Brother Machine > Print Settings for Photos Print Settings for Photos Press the [Print Settings] option to display the settings shown in the table. Option Description Print Quality Select the print resolution for your type of document. (Does not appear when Digital Print Order Format (DPOF) Print is selected) • Paper Type Select the paper type. Paper Size Select the paper size.
Print Size Option Printed Position 4"x6" 5"x7" 6"x8" Max.
Home > PhotoCapture Center > Copy Photos from Media to a Computer Copy Photos from Media to a Computer If you would like to copy photos stored in a memory card or USB flash drive to a folder on your computer, follow the steps for your connection type and Operating System.
Home > PhotoCapture Center > Copy Photos from Media to a Computer > Before Copying Photos Before Copying Photos IMPORTANT DO NOT start your computer with a memory card or USB flash drive in the media drive of the machine. You could lose your data or damage the media. • The PhotoCapture Center will read only the media that was put in first. • While the machine is printing from the PhotoCapture Center, your computer cannot access the PhotoCapture Center for any other operation.
Home > PhotoCapture Center > Copy Photos from Media to a Computer > Copy Photos from Media Over a Local Connection Copy Photos from Media Over a Local Connection You can copy photos from media to your computer when it is locally connected (via USB) to your machine. 1. Open the machine's media slot cover. 2. Insert a memory card or USB flash drive into your machine. 3. Do one of the following: • ( Windows®) In Windows® Explorer, double-click the Removable Disk icon.
Home > PhotoCapture Center > Copy Photos from Media to a Computer > Copy Photos from Media Over a Network Connection Copy Photos from Media Over a Network Connection You can copy photos from media to your computer when it is connected to the machine using a Network connection. 1. Open the machine's media slot cover. 2. Insert a memory card or USB flash drive into your machine. 3. Type the IP address of your Brother machine in your web browser (where XXX.XXX.XXX.XXX is your Brother machine's IP address).
Home > PhotoCapture Center > Print Photos from ControlCenter4 (Windows®) Print Photos from ControlCenter4 (Windows®) You can print and edit photos using various ControlCenter features. 1. Make sure you have loaded the correct media in the paper tray. IMPORTANT • We recommend using the photo bypass tray located on the top of the output tray cover to print on Photo (4" x 6")/(10 x 15 cm) and Photo L (3.5" x 5")/(9 x 13 cm) paper. (available only for certain models) • For best results, use Brother paper.
Option Description Select All Selects all thumbnails in the current view. Deselect All Deselects all thumbnails in the current view. 6. Specify the number of copies you want to print (1-99) by clicking . 7. To trim the photo before printing, click Edit. 8. Click Print. The print settings window appears. 9. Configure the settings for the Paper Size, Media Type, and Layout options. 10. Click the Properties button to configure the Print Quality, Color / Grayscale and Color Mode options, if needed.
Home > PhotoCapture Center > Print Photos from ControlCenter4 (Windows®) > Edit Photos Using ControlCenter4 (Windows®) Edit Photos Using ControlCenter4 (Windows®) 3 4 5 1. This area shows which images are currently selected, and how many copies of each image will be printed. 2. These buttons allow you to control how you view the selected image. Description Buttons (Compare) Compare the edited image with the original. (Undo) Cancel the last edit applied to the selected image.
5. Image Enhancement Nature Scene Select this option to enhance natural colors, such as green and blue. Night Scene Select this option to optimize the image adjustments for a night scene photo. Soft Light Select this option to soften bright edges.
Home > Network Network • Get Started • Network Management Software and Utilities • Additional Methods of Configuring Your Brother Machine for a Wireless Network • Advanced Network Features • Technical Information for Advanced Users 352
Home > Network > Get Started Get Started We recommend setting up and connecting to your network using the Brother installation CD-ROM. This section provides more information on network connection types, introduces various methods to manage your network and explains some useful network features of your Brother machine.
Home > Network > Get Started > Supported Basic Network Features Supported Basic Network Features The print server supports various features depending on the operating system. Use this chart to see what network features and connections are supported by each operating system. Operating Systems Windows® XP Windows Vista® Windows Server® 2003/2008/2012/2012 R2 OS X v10.8.5 OS X v10.9.x OS X v10.10.
Home > Network > Network Management Software and Utilities Network Management Software and Utilities Configure and change your Brother machine's network settings using a management utility.
Home > Network > Network Management Software and Utilities > Learn about Network Management Software and Utilities Learn about Network Management Software and Utilities BRAdmin Light (Windows®) BRAdmin Light is a utility for the initial setup of Brother network-connected devices. This utility can search for Brother products on your network, view the status and configure the basic network settings, such as IP address. Go to your model's Downloads page on the Brother Solutions Center at support.brother.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network Additional Methods of Configuring Your Brother Machine for a Wireless Network To connect your machine to your wireless network, we recommend using the Installation CD-ROM.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Before Configuring Your Brother Machine for a Wireless Network Before Configuring Your Brother Machine for a Wireless Network Before attempting to configure a wireless network, confirm the following: • To achieve optimum results with normal everyday document printing, place the Brother machine as close to the wireless LAN access point/router as possible with minimal obstructions.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Configure Your Machine for a Wireless Network Using the One Push Method of Wi-Fi Protected Setup™ (WPS) or AOSS™ Configure Your Machine for a Wireless Network Using the One Push Method of Wi-Fi Protected Setup™ (WPS) or AOSS™ If your wireless access point/router supports either WPS (Push Button Configuration) or AOSS™, you can use WPS or AOSS™ from your machine's control panel menu to configure your wireless ne
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Configure Your Machine for a Wireless Network Using the PIN Method of Wi-Fi Protected Setup™ (WPS) Configure Your Machine for a Wireless Network Using the PIN Method of Wi-Fi Protected Setup™ (WPS) If your wireless LAN access point/router supports WPS, you can use the Personal Identification Number (PIN) Method to configure your wireless network settings.
• The Registrar is usually the wireless LAN access point/router. • The settings page will differ depending on the brand of wireless LAN access point/router. For more information, see the instructions supplied with your wireless LAN access point/router. If you are using a Windows Vista®, Windows® 7, Windows® 8, or Windows® 10 computer as a Registrar, complete the following steps: 6. Do one of the following: Windows Vista® • Click (Start) > Network > Add a wireless device.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Configure Your Machine for a Wireless Network in Ad-Hoc Mode Using a New SSID Configure Your Machine for a Wireless Network in Ad-Hoc Mode Using a New SSID You must connect to a new SSID from your computer when it is configured for Ad-Hoc mode. 1. Press [Settings] > [All Settings] > [Network] > [WLAN] > [Setup Wizard]. 2. When [Switch Network interface to wireless?] or [Enable WLAN?] appears, press [Yes].
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Configure Your Machine for a Wireless Network When the SSID is Not Broadcast Configure Your Machine for a Wireless Network When the SSID is Not Broadcast Before configuring your machine, we recommend writing down your wireless network settings. You will need this information before you continue with the configuration. 1. Check and write down the current wireless network settings.
• For more information about how to enter text, see the Appendix. • Your Brother machine supports the use of the first WEP key only. 10. To apply the settings, press [Yes]. To cancel, press [No]. 11. The machine attempts to connect to the wireless device you have selected. If your wireless device is connected successfully, the LCD displays [Connected]. You have completed the wireless network setup.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® Use Wi-Fi Direct® • Print or Scan from Your Mobile Device Using Wi-Fi Direct • Configure Your Wi-Fi Direct Network • I Cannot Complete the Wireless Network Setup Configuration 365
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® > Print or Scan from Your Mobile Device Using Wi-Fi Direct Print or Scan from Your Mobile Device Using Wi-Fi Direct Wi-Fi Direct is one of the wireless configuration methods developed by the Wi-Fi Alliance®.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® > Configure Your Wi-Fi Direct Network Configure Your Wi-Fi Direct Network Configure your Wi-Fi Direct network settings from your machine's control panel.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® > Configure Your Wi-Fi Direct Network > Wi-Fi Direct Network Configuration Overview Wi-Fi Direct Network Configuration Overview The following instructions offer five methods for configuring your Brother machine in a wireless network environment. Select the method you prefer for your environment. Check your mobile device for configuration. 1.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® > Configure Your Wi-Fi Direct Network > Configure Your Wi-Fi Direct Network Using the OnePush Method Configure Your Wi-Fi Direct Network Using the One-Push Method If your mobile device supports Wi-Fi Direct, follow these steps to configure a Wi-Fi Direct network: When the machine receives the Wi-Fi Direct request from your mobile device, the message [Wi-Fi Direct connection request received.
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® > Configure Your Wi-Fi Direct Network > Configure Your Wi-Fi Direct Network Using the OnePush Method and Wi-Fi Protected Setup™ (WPS) Configure Your Wi-Fi Direct Network Using the One-Push Method and Wi-Fi Protected Setup™ (WPS) If your mobile device supports WPS (PBC; Push Button Configuration), follow these steps to configure a Wi-Fi Direct network: When the machine receives the Wi-Fi Direct
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® > Configure Your Wi-Fi Direct Network > Configure Your Wi-Fi Direct Network Using the PIN Method Configure Your Wi-Fi Direct Network Using the PIN Method If your mobile device supports the PIN Method of Wi-Fi Direct, follow these steps to configure a Wi-Fi Direct network: When the machine receives the Wi-Fi Direct request from your mobile device, the message [Wi-Fi Direct connection request re
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® > Configure Your Wi-Fi Direct Network > Configure Your Wi-Fi Direct Network Using the PIN Method of Wi-Fi Protected Setup™ (WPS) Configure Your Wi-Fi Direct Network Using the PIN Method of Wi-Fi Protected Setup™ (WPS) If your mobile device supports the PIN Method of Wi-Fi Protected Setup™ (WPS), follow these steps to configure a Wi-Fi Direct network: When the machine receives the Wi-Fi Direct
Home > Network > Additional Methods of Configuring Your Brother Machine for a Wireless Network > Use Wi-Fi Direct® > Configure Your Wi-Fi Direct Network > Configure Your Wi-Fi Direct Network Manually Configure Your Wi-Fi Direct Network Manually If your mobile device does not support Wi-Fi Direct or WPS, you must configure a Wi-Fi Direct network manually. 1. Press [Settings] > [All Settings] > [Network] > [Wi-Fi Direct] > [Manual]. 2. When [Wi-Fi Direct On?] appears, press [On] to accept.
Home > Network > Advanced Network Features Advanced Network Features • Print the Network Configuration Report 374
Home > Network > Advanced Network Features > Print the Network Configuration Report Print the Network Configuration Report The Network Configuration Report lists the network configuration, including the network print server settings. • Node Name: The Node Name appears on the current Network Configuration Report. The default Node Name is "BRNxxxxxxxxxxxx" for a wired network or "BRWxxxxxxxxxxxx" for a wireless network (where "xxxxxxxxxxxx" is your machine's MAC Address / Ethernet Address.
Home > Network > Technical Information for Advanced Users Technical Information for Advanced Users • Reset the Network Settings to Factory Default • Print the WLAN Report 376
Home > Network > Technical Information for Advanced Users > Reset the Network Settings to Factory Default Reset the Network Settings to Factory Default You can use your machine's control panel to reset the print server to its default factory settings. This resets all information, such as the password and IP address. • This feature restores all wired (supported models only) and wireless network settings to the factory settings.
Home > Network > Technical Information for Advanced Users > Print the WLAN Report Print the WLAN Report The WLAN Report reflects your machine's wireless status. If the wireless connection fails, check the error code on the printed report. 1. Press [Settings] > [All Settings] > [Print Reports] > [WLAN Report] > [OK]. The machine will print the WLAN Report. If the WLAN Report does not print, check your machine for errors.
Home > Network > Technical Information for Advanced Users > Print the WLAN Report > Wireless LAN Report Error Codes Wireless LAN Report Error Codes If the Wireless LAN Report shows that the connection failed, check the error code on the printed report and see the corresponding instructions in the table: Error Code Problem and Recommended Solutions TS-01 The wireless setting is not activated, change the wireless setting to ON.
Error Code Problem and Recommended Solutions TS-08 Two or more wireless access points that have WPS or AOSS™ enabled are detected. • Confirm that only one wireless access point/router within range has the WPS or AOSS™ method active and try again. • Try starting again after a few minutes to avoid interference from other access points.
Home > Security Security • Lock the Machine Settings 381
Home > Security > Lock the Machine Settings Lock the Machine Settings Before turning on the machine's access lock feature, make a careful note of your password. If you forget the password, you must reset all passwords stored in the machine by calling your administrator or Brother Customer Service.
Home > Security > Lock the Machine Settings > About Using Memory Security About Using Memory Security Memory Security lets you prevent unauthorized access to the machine. Although you cannot schedule Delayed Faxes or Polling jobs, any pre-scheduled Delayed Faxes will be sent. You must turn off PC Fax Receive before you can turn on Memory Security.
Home > Security > Lock the Machine Settings > About Using Memory Security > Set the Memory Security Password Set the Memory Security Password Make a careful note of your password. 1. Press [Settings] > [All Settings] > [Fax] > [Miscellaneous] > [Memory Security]. 2. Enter a four-digit number for the password using the touchscreen. Press [OK]. 3. When the touchscreen displays [Verify], re-enter the password using the touchscreen. Press [OK]. 4. Press .
Home > Security > Lock the Machine Settings > About Using Memory Security > Change the Memory Security Password Change the Memory Security Password 1. Press [Settings] > [All Settings] > [Fax] > [Miscellaneous] > [Memory Security] > [Set Password]. 2. Enter the registered four-digit number for the current password using the touchscreen. Press [OK]. 3. Enter a four-digit number for a new password using the touchscreen. Press [OK]. 4.
Home > Security > Lock the Machine Settings > About Using Memory Security > Turn Memory Security On/Off Turn Memory Security On/Off 1. Press [Settings] > [All Settings] > [Fax] > [Miscellaneous] > [Memory Security] > [Set Security]. 2. Enter the registered four-digit password using the keyboard on the touchscreen. Press [OK]. The machine goes offline and the touchscreen displays [Memory Security]. Turning off Memory Security: a. Press [Unlock]. b.
Home > Mobile/Web Connect Mobile/Web Connect • Use Web Services from Your Brother Machine • Use Brother Web Services • Print with Google Cloud Print™ • Print with AirPrint • Print with Mopria® • Print and Scan from a Mobile Device • Print and Scan Using Near-Field Communication (NFC) 387
Home > Mobile/Web Connect > Use Web Services from Your Brother Machine Use Web Services from Your Brother Machine Certain websites provide services that allow users to upload and view images and files on the website. Your Brother machine can scan images and upload them to these services, and also download from and print images that are already uploaded to these services. 1 3 2 4 1. Printing 2. Scanning 3. Photos, images, documents and other files 4.
Home > Mobile/Web Connect > Use Brother Web Services Use Brother Web Services Brother Web Services allow you to scan, print, and perform other features that help you save files to the Cloud, upload to other services. Brother Web Services also manage cloud servers, so you can transfer received faxes. • Outline and Scan Use a red pen to outline sections of your document, and then scan the document.
Related Information • Mobile/Web Connect 390
Home > Mobile/Web Connect > Print with Google Cloud Print™ Print with Google Cloud Print™ Google Cloud Print™ is a Google-provided service that allows you to print to a printer registered to your Google account using a network-compatible device (such as a mobile phone or computer) without installing the printer driver on the device. 1 2 3 4 1. Print request 2. Internet 3. Google Cloud Print™ 4. Printing For more detailed information, see the Google Cloud Print Guide.
Home > Mobile/Web Connect > Print with AirPrint Print with AirPrint Use Brother AirPrint to wirelessly print photos, emails, web pages, and documents from your iPad, iPhone and iPod touch without installing a printer driver on the device. 1 2 1. Print request 2. Printed photos, emails, web pages, and documents • AirPrint also lets you send faxes directly from your Mac computer without printing them. 1 2 3 1. Wired or wireless network 2. Telephone line 3.
Home > Mobile/Web Connect > Print with Mopria® Print with Mopria® Mopria® Print Service is a print feature on Android™ phones or tablets (Android™ version 4.4 or later) developed by the Mopria® Alliance. With this service, you can connect to the same network as the printer and print without additional setup. Many native Android™ apps, including Google Chrome™, Gmail™ and Gallery, support printing. 2 1 3 1. Android™ 4.4 or later 2. Wi-Fi® Connection 3.
Home > Mobile/Web Connect > Print and Scan from a Mobile Device Print and Scan from a Mobile Device Use Brother iPrint&Scan to print and scan from various mobile devices. • For Android™ Devices Brother iPrint&Scan allows you to use features of your Brother machine directly from your Android™ device, without using a computer. Download and install Brother iPrint&Scan from the Google Play™ Store app.
Home > Mobile/Web Connect > Print and Scan Using Near-Field Communication (NFC) Print and Scan Using Near-Field Communication (NFC) Near-Field Communication (NFC) allows for simple transactions, data exchange and wireless connections between two devices that are close to each other.
Home > ControlCenter ControlCenter Use Brother's ControlCenter software utility to quickly access your frequently-used applications. Using ControlCenter gives you direct access to specific applications.
Home > ControlCenter > ControlCenter4 (Windows®) ControlCenter4 (Windows®) • Change the Operation Mode in ControlCenter4 (Windows®) • Scan Using ControlCenter4 Home Mode (Windows®) • Scan Using ControlCenter4 Advanced Mode (Windows®) • Set Up the Brother Machine Using ControlCenter4 (Windows®) • Create a Custom Tab Using ControlCenter4 Advanced Mode (Windows®) • Set Up the Brother Machine from Your Computer (Windows®) • Set Up Your Brother Address Book Using ControlCenter4 (Windows®) 397
Home > ControlCenter > ControlCenter4 (Windows®) > Change the Operation Mode in ControlCenter4 (Windows®) Change the Operation Mode in ControlCenter4 (Windows®) ControlCenter4 has two operation modes: Home Mode and Advanced Mode. You can change modes at any time. Home Mode Advanced Mode • Home Mode ControlCenter4 Home Mode lets you access your machine's main features easily.
• Advanced Mode ControlCenter4 Advanced Mode gives you more control over the details of your machine's features and allows you to customize one-button scan actions. To change operation mode: 1. Click the (ControlCenter4) icon in the task tray, and then select Open. 2. Click the Configuration button, and then select Mode Select. 3. The mode selection dialog box appears. Select either the Home Mode or Advanced Mode option. 4. Click OK.
Home > ControlCenter > ControlCenter4 (Windows®) > Scan Using ControlCenter4 Home Mode (Windows®) Scan Using ControlCenter4 Home Mode (Windows®) Use ControlCenter4 Home Mode to access your machine's main features.
Home > ControlCenter > ControlCenter4 (Windows®) > Scan Using ControlCenter4 Advanced Mode (Windows®) Scan Using ControlCenter4 Advanced Mode (Windows®) ControlCenter4 Advanced Mode gives you more control over the details of your machine's features and allows you to customize one-button scan actions.
Home > ControlCenter > ControlCenter4 (Windows®) > Set Up the Brother Machine Using ControlCenter4 (Windows®) Set Up the Brother Machine Using ControlCenter4 (Windows®) 1. Click the (ControlCenter4) icon in the task tray, and then click Open. 2. Click the Device Settings tab. 3. Click the Remote Setup button. 4. Configure the settings as needed. Export Click to save the current configuration settings to a file. Click Export to save your address book or all settings for your machine.
OK Click to start uploading data to the machine, and then exit the Remote Setup Program. If an error message appears, confirm that your data is correct, and then click OK. Cancel Click to exit the Remote Setup Program without uploading data to the machine. Apply Click to upload data to the machine without exiting the Remote Setup Program. 5. Click OK.
Home > ControlCenter > ControlCenter4 (Windows®) > Create a Custom Tab Using ControlCenter4 Advanced Mode (Windows®) Create a Custom Tab Using ControlCenter4 Advanced Mode (Windows®) You can create up to three customized tabs, each including up to five customized buttons, with your preferred settings. Select Advanced Mode as the mode setting for ControlCenter4. 1. Click the (ControlCenter4) icon in the task tray, and then click Open. 2. Click the Configuration button, and then select Create custom tab.
Related Information • ControlCenter4 (Windows®) 405
Home > ControlCenter > ControlCenter2 (Mac) ControlCenter2 (Mac) • Scan Using ControlCenter2 (Mac) • Set Up the Brother Machine Using ControlCenter2 (Mac) • Turn On the AutoLoad Feature (Mac) • Set Up Your Brother Address Book Using ControlCenter2 (Mac) 406
Home > ControlCenter > ControlCenter2 (Mac) > Scan Using ControlCenter2 (Mac) Scan Using ControlCenter2 (Mac) Use Brother's ControlCenter software to scan photos and save them as JPEGs, PDFs, or other file formats.
Home > ControlCenter > ControlCenter2 (Mac) > Set Up the Brother Machine Using ControlCenter2 (Mac) Set Up the Brother Machine Using ControlCenter2 (Mac) 1. In the Finder menu bar, click Go > Applications > Brother, and then double-click the (ControlCenter) icon. The ControlCenter2 screen appears. 2. Click the DEVICE SETTINGS tab. 3. Click the Remote Setup button. The Remote Setup Program screen appears. 4. Configure the settings as needed.
Click Export to save your address book or all settings for your machine. Import Click to read the settings from a file. Print Click to print the selected items on the machine. You cannot print the data until it is uploaded to the machine. Click Apply to upload the new data to the machine, and then click Print. OK Click to start uploading data to the machine, and then exit the Remote Setup Program. If an error message appears, enter the correct data again, and then click OK.
Home > ControlCenter > ControlCenter2 (Mac) > Turn On the AutoLoad Feature (Mac) Turn On the AutoLoad Feature (Mac) Turn on AutoLoad to launch ControlCenter2 automatically each time you start your Mac. 1. In the Finder menu bar, click Go > Applications > Brother, and then double-click the (ControlCenter) icon. The ControlCenter2 screen appears. 2. Click the Configuration button, and then select Preferences. 3. Select the Start ControlCenter on computer startup check box. 4. Click OK.
Home > Troubleshooting Troubleshooting If you think there is a problem with your machine, first check each of the items below, then try to identify the problem, and follow our troubleshooting tips. You can correct most problems yourself. If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at support.brother.com. Click FAQs & Troubleshooting and search for your model name.
Home > Troubleshooting > Error and Maintenance Messages Error and Maintenance Messages As with any sophisticated office product, errors may occur and supply items may have to be replaced. If this happens, your machine identifies the error or required routine maintenance and shows the appropriate message. The most common error and maintenance messages are shown in the table. You can correct most errors and perform routine maintenance yourself.
Error Message Cause Action An ink cartridge is not installed correctly. See Related Information: Replace the Ink Cartridges. A used ink cartridge was reinstalled. Remove the used ink cartridge and install a new one. If you are not using Genuine Brother ink, the machine may not detect the ink cartridge. Use a new Genuine Brother Ink Cartridge. If the error is not cleared, call Brother Customer Service. The ink cartridge must be replaced.
Error Message Cause Action Data Remaining in Memory Print data is left in the machine's memory. Press Disconnected The other person or other person's fax machine stopped the call. . The machine will cancel the job and clear it from the memory. Try to print again. Try to send or receive again. If calls are stopped repeatedly and you are using a VoIP (Voice over IP) system, try changing the Compatibility to Basic (for VoIP). See Related Information: Telephone Line Interference/VoIP.
Error Message Cause Action the machine requires, the faster these boxes will fill up. Repairs resulting from the use of nonBrother supplies may not be covered under the stated product warranty. Ink Absorber Pad NearFull The ink absorber box or flushing box is nearly full. The ink absorber box or flushing box must be replaced soon. Call Brother Customer Service or a Brother Authorized Service Center to have your machine serviced.
Error Message Cause Action Low Temperature The room temperature is too low. After warming the room, allow the machine to warm up to room temperature. Try again when the machine has warmed up. Media card error Multiple data storage devices were in the machine when it was turned on. The machine can read only one memory card or USB flash drive at a time. Remove the memory cards or USB flash drives that you are not using.
Error Message Cause Action The photo bypass tray is in the wrong position. Return the photo bypass tray to the Normal printing position when you use cut sheet paper. See Related Information: Load Photo or Photo L Paper in Photo Bypass Tray. The paper was not inserted in the center position of the manual feed slot. Remove the paper and reinsert it in the center of the manual feed slot, and then follow the on-screen instructions. See Related Information: Load Paper in the Manual Feed Slot.
Error Message Cause Action See Related Information: Load Paper. 3. After you have checked the paper size and the paper position, follow the on‑screen instructions. If printing from your computer, make sure the paper size you selected in the printer driver matches the size of paper in the tray. See Related Information: Print Settings (Windows®) or Print Options (Mac). Paper Tray not detected The paper tray is not completely inserted. Slowly push the paper tray completely into the machine.
Error Message Cause Action the power for several minutes and reconnect it. (The machine can be turned off without losing faxes stored in the memory. ) See Related Information: Transfer Your Faxes or Fax Journal Report. Unusable Device Disconnect device from front connector & turn machine off & then on Unusable Device Please disconnect USB device. Wrong Ink Cartridge A broken device is connected to the USB direct interface.
• Print Options (Mac) • Paper Handling and Printing Problems 420
Home > Troubleshooting > Error and Maintenance Messages > Transfer Your Faxes or Fax Journal Report Transfer Your Faxes or Fax Journal Report If the LCD shows: • [Unable to Clean XX] • [Unable to Initialize XX] • [Unable to Print XX] • [Unable to Scan XX] We recommend transferring your faxes to another fax machine or to your computer. See Related Information: Transfer Faxes to Another Fax Machine. See Related Information: Transfer Faxes to Your Computer.
Home > Troubleshooting > Error and Maintenance Messages > Transfer Your Faxes or Fax Journal Report > Transfer Faxes to Another Fax Machine Transfer Faxes to Another Fax Machine If you have not set up your Station ID, you cannot enter fax transfer mode. 1. Press to interrupt the error temporarily. 2. Press [Settings] > [All Settings] > [Service] > [Data Transfer] > [Fax Transfer]. 3. Do one of the following: • If the touchscreen displays [No Data], there are no faxes left in the machine’s memory.
Home > Troubleshooting > Error and Maintenance Messages > Transfer Your Faxes or Fax Journal Report > Transfer Faxes to Your Computer Transfer Faxes to Your Computer You can transfer the faxes from your machine's memory to your computer. 1. Press to interrupt the error temporarily. 2. Make sure you have installed the Brother driver on your computer, and then turn on PC-FAX Receive on the computer.
Home > Troubleshooting > Error and Maintenance Messages > Transfer Your Faxes or Fax Journal Report > Transfer the Fax Journal Report to Another Fax Machine Transfer the Fax Journal Report to Another Fax Machine If you have not set up your Station ID, you cannot enter fax transfer mode. 1. Press to interrupt the error temporarily. 2. Press [Settings] > [All Settings] > [Service] > [Data Transfer] > [Report Transfer]. 3. Enter the fax number where the Fax Journal report will be forwarded. 4.
Home > Troubleshooting > Document Jams Document Jams • Document is Jammed in the Top of the ADF Unit • Document is Jammed inside the ADF Unit • Remove Paper Scraps Jammed in the ADF • Error and Maintenance Messages 425
Home > Troubleshooting > Document Jams > Document is Jammed in the Top of the ADF Unit Document is Jammed in the Top of the ADF Unit 1. Remove any paper from the ADF. 2. Open the ADF cover. 3. Remove the jammed document by pulling it upward. 4. Close the ADF cover. 5. Press . IMPORTANT To avoid future document jams, close the ADF cover correctly by pressing it down in the center.
Home > Troubleshooting > Document Jams > Document is Jammed inside the ADF Unit Document is Jammed inside the ADF Unit 1. Remove any paper that is not jammed from the ADF. 2. Lift the document cover. 3. Pull the jammed document out to the left. 4. Close the document cover. 5. Press .
Home > Troubleshooting > Document Jams > Remove Paper Scraps Jammed in the ADF Remove Paper Scraps Jammed in the ADF 1. Lift the document cover. 2. Insert a piece of stiff paper, such as cardstock, into the ADF to push any small paper scraps through. 3. Close the document cover. 4. Press .
Home > Troubleshooting > Printer Jam or Paper Jam Printer Jam or Paper Jam Locate and remove the jammed paper.
Home > Troubleshooting > Printer Jam or Paper Jam > Paper is Jammed Inside and in the Front of the Machine (Jam A Inside/Front) Paper is Jammed Inside and in the Front of the Machine (Jam A Inside/ Front) If the LCD displays [Jam A Inside/Front] or [Repeat Jam A Inside/Front], follow these steps: 1. Unplug the machine from the AC power outlet. 2. Pull the paper tray (1) completely out of the machine. 1 3. Pull the two green levers inside the machine to release the jammed paper. 4.
If your LCD error message was [Repeat Jam A Inside/Front], move the print head (if needed) to take out any paper remaining in this area. Make sure scraps of paper are not left in the corners of the machine (1) and (2). 2 1 When finished, continue with the next step. IMPORTANT • DO NOT touch the encoder strip, a thin strip of plastic that stretches across the width of the machine (1). Doing this may cause damage to the machine.
2 3 • If ink gets on your skin or clothing, immediately wash it off with soap or detergent. 6. Gently close the scanner cover using both hands. 7. Slowly pull the jammed paper (1) out of the machine.
If your LCD error message was [Repeat Jam A Inside/Front], do the following: a. Make sure you look carefully inside (1) for any scraps of paper. 1 b. Squeeze both levers (1), and then open the Jam Clear Cover at the back of the machine. 1 c. Slowly pull the jammed paper out of the machine. d. Close the Jam Clear Cover. Make sure the cover is closed completely. When finished, continue with the next step. 8. Put the paper tray firmly back in the machine.
9. While holding the paper tray in the machine, pull out the paper support (1) until it locks into place, and then unfold the paper support flap (2). 2 1 10. Reconnect the power cord.
Home > Troubleshooting > Printer Jam or Paper Jam > Paper is Jammed in the Front of the Machine (Jam B Front) Paper is Jammed in the Front of the Machine (Jam B Front) If the LCD displays [Jam B Front] or [Repeat Jam B Front], follow these steps: 1. Unplug the machine from the AC power outlet. 2. Pull the paper tray (1) completely out of the machine. 1 3. Pull the two green levers inside the machine to release the jammed paper. 4. Slowly pull out the jammed paper (1).
If your LCD error message was [Repeat Jam B Front], do the following: a. Make sure you look carefully inside (1) for any scraps of paper. 1 b. Squeeze both levers (1), and then open the Jam Clear Cover at the back of the machine. 1 c. Slowly pull the jammed paper out of the machine. d. Close the Jam Clear Cover. Make sure the cover is closed completely. When finished, continue with the next step. 5. Put the paper tray firmly back in the machine.
6. While holding the paper tray in the machine, pull out the paper support (1) until it locks into place, and then unfold the paper support flap (2). 2 1 7. Reconnect the power cord.
Home > Troubleshooting > Printer Jam or Paper Jam > Paper is Jammed in the Back of the Machine (Jam C Rear) Paper is Jammed in the Back of the Machine (Jam C Rear) If the LCD displays [Jam C Rear], follow these steps: 1. Unplug the machine from the AC power outlet. 2. Pull the paper tray (1) completely out of the machine. 1 3. Pull the two green levers inside the machine to release the jammed paper.
7. Put the paper tray firmly back in the machine. 8. While holding the paper tray in the machine, pull out the paper support (1) until it locks into place, and then unfold the paper support flap (2). 2 1 9. Reconnect the power cord.
Home > Troubleshooting > If You Are Having Difficulty with Your Machine If You Are Having Difficulty with Your Machine For technical help, you must call the country where you bought the machine. Calls must be made from within that country. If you think there is a problem with your machine, check the following topics. You can correct most problems yourself. If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit support.brother.com.
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Paper Handling and Printing Problems Paper Handling and Printing Problems Printing Difficulties Difficulties Suggestions No printout Check that the correct printer driver has been installed and selected. Check to see if the machine's display is showing an error message. See Related Information: Error and Maintenance Messages.
Difficulties Suggestions • Windows® XP and Windows Server® 2003 Click the Start > Printers and Faxes. • Windows Vista® and Windows Server® 2008 Click • Windows® 7 and Windows Server® 2008 R2 Click • /Start > Control Panel > Hardware and Sound > Printers. /Start > Devices and Printers > Printers and Faxes. Windows® 8 Move your mouse to the lower right corner of your desktop. When the menu bar appears, click Settings > Control Panel.
Difficulties Suggestions See Related Information: Print Settings (Windows®) or Print Options (Mac). Make sure your ink cartridges are fresh. The following may cause ink to clog: • The expiration date written on the cartridge package has passed. • The ink cartridge has been in your machine for over six months. • The ink cartridge may not have been stored correctly before use. Make sure you are using Genuine Brother Ink.
Difficulties Suggestions Ink is smudged or wet when using Be sure to check the front and back of the paper. Place the glossy surface glossy photo paper. (printing surface) face down. See Related Information: Change the Paper Size and Paper Type. If you use glossy photo paper, make sure the paper type setting is correct. Stains appear on the reverse side Make sure the printer platen is not dirty with ink. or at the bottom of the page. See Related Information: Clean the Machine's Printer Platen.
Difficulties Suggestions Make sure the Jam Clear Cover is closed correctly. See Related Information: Printer Jam or Paper Jam. Make sure the Base Pad in the paper tray is not dirty. See Related Information: Clean the Paper Pick-up Rollers. There is a paper jam. See Related Information: Printer Jam or Paper Jam. Make sure the paper guides are set to the correct paper size. DO NOT extend the paper tray when you load A5 or smaller size paper. The paper jams when you use 2sided copy or 2-sided print.
• Clean the Print Head from Your Brother Machine • Clean the Print Head from Your Computer (Windows®) • Clean the Print Head from Your Computer (Mac) • Check the Print Alignment from Your Brother Machine • Load Paper • Clean the Machine's Printer Platen • Clean the Paper Feed Rollers • Clean the Paper Pick-up Rollers • Printer Jam or Paper Jam • Copy on Both Sides of the Paper (1-sided to 2-sided/2-sided to 2-sided) • Shrink Page Size of an Oversized Incoming Fax • Paper Weight and Thickness • Print Setting
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Telephone and Fax problems Telephone and Fax problems Telephone Line or Connections Difficulties Suggestions Dialing does not work. (No dial tone) Check all line cord connections. Make sure the telephone line cord is plugged into the telephone wall jack and the LINE jack of the machine. Make sure your machine has a dial tone by pressing the Hook button in Fax mode.
Difficulties Suggestions a slight interruption is crucial to your business, we recommend using a separate telephone line with no custom features. Receiving Faxes Difficulties Suggestions Cannot receive a fax. Make sure your machine has a dial tone by pressing the Hook button in Fax mode. If you hear static or interference on your fax line, contact your local telephone provider. Check all line cord connections.
Difficulties Suggestions If you are using a telephone answering machine (External TAD mode) on the same line as the Brother machine, make sure your answering machine is set up correctly. See Related Information: Connect an External TAD. 1. Plug the telephone line cord directly from the telephone wall jack to your Brother machine’s LINE jack. 2. Remove the protective cap from your Brother machine’s EXT jack, and then plug the telephone line cord from your answering machine into the EXT jack. 3.
Difficulties Suggestions See Related Information: Cancel a Fax in Progress. See Related Information: Check and Cancel a Pending Fax. If you often get transmission errors due to possible interference on the telephone line or if you are using a VoIP system, try changing the Compatibility setting to Basic(for VoIP). See Related Information: Telephone Line Interference/VoIP. Sent faxes are blank. Make sure you are loading the document correctly.
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Telephone and Fax problems > Set Dial Tone Detection Set Dial Tone Detection Setting the Dial Tone to [Detection] will shorten the Dial Tone detect pause. 1. Press [Settings] > [All Settings] > [Initial Setup] > [Dial Tone]. 2. Press [Detection] or [No Detection]. 3. Press .
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Telephone and Fax problems > Telephone Line Interference/VoIP Telephone Line Interference/VoIP If you are having problems sending or receiving a fax due to possible interference on the telephone line or if you are using a VoIP system, we recommend changing the modem speed to minimize errors in fax operations. 1. Press [Settings] > [All Settings] > [Initial Setup] > [Compatibility]. 2. Press [Normal] or [Basic(for VoIP)].
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Other Problems Other Problems Copying Difficulties Difficulties Suggestions Vertical black lines or streaks appear in copies. Black vertical lines on copies are typically caused by dirt or correction fluid on the glass strip. Clean the glass strip, scanner glass, and the white bar and white plastic above them. See Related Information: Clean the Scanner. Black marks or spots appear in copies.
Difficulties Suggestions Cannot access Removable Disk from the computer. Make sure you have correctly inserted the memory card or USB Flash drive. Part of my photo is missing when printed. Make sure Borderless printing and Cropping are turned off. See Related Information: Print Borderless Photos from Media. See Related Information: Print Photos with Auto Cropping. Software Difficulties Difficulties Suggestions Cannot print. Uninstall and reinstall the Brother driver.
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Network Problems Network Problems • Use the Network Connection Repair Tool (Windows®) • Where Can I Find My Brother Machine's Network Settings? • I Cannot Complete the Wireless Network Setup Configuration • My Brother Machine Cannot Print, Scan, or PC-FAX Receive over the Network • I Want to Check that My Network Devices are Working Correctly • Troubleshooting 455
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Network Problems > Use the Network Connection Repair Tool (Windows®) Use the Network Connection Repair Tool (Windows®) Use the Network Connection Repair Tool to fix the Brother machine's network settings. It will assign the correct IP address and Subnet Mask. • Windows® XP/XP Professional x64 Edition/Windows Vista®/Windows® 7/Windows® 8/Windows® 10 You must log on with Administrator rights.
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Network Problems > Where Can I Find My Brother Machine's Network Settings? Where Can I Find My Brother Machine's Network Settings? • Change Machine Settings from Your Computer • Print the Network Configuration Report 457
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Network Problems > I Cannot Complete the Wireless Network Setup Configuration I Cannot Complete the Wireless Network Setup Configuration Turn your wireless router off and back on. Then try to configure the wireless settings again. If you are unable to resolve the problem, follow the instructions below: Investigate the problem using the WLAN Report. Cause Action Your security settings (SSID/ • Network Key) are not correct.
Cause Action If you have checked and • tried all of the above, but still cannot complete the Wi-Fi • Direct configuration, do the following: Interface Turn your Brother machine off and back on. Then try to configure Wi-Fi Direct the Wi-Fi Direct settings again. If you are using your Brother machine as a client, confirm how many devices are allowed in the current Wi-Fi Direct network, and then check how many devices are connected.
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Network Problems > My Brother Machine Cannot Print, Scan, or PC-FAX Receive over the Network My Brother Machine Cannot Print, Scan, or PC-FAX Receive over the Network Cause Action Your security software blocks your machine's access to the network. (The Network scanning feature does not work. ) • Windows® Interface Wired/Wireless Configure the third-party Security/Firewall Software to allow Network scanning.
Cause Action - Interface Windows® XP/Windows Server® 2003 Click Start > Printers and Faxes. - Windows Vista® Click (Start) > Control Panel > Hardware and Sound > Printers. - Windows® 7 Click (Start) > Devices and Printers > Printers and Faxes. - Windows® 8 Move your mouse to the lower right corner of your desktop. When the menu bar appears, click Settings > Control Panel. In the Hardware and Sound group, click View devices and printers > Printers.
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Network Problems > I Want to Check that My Network Devices are Working Correctly I Want to Check that My Network Devices are Working Correctly Check Action Interface Wired/Wireless Check that your Brother Check the following: machine, access point/ • The power cord is connected correctly and the Brother machine is router, or network hub is turned on. turned on.
Home > Troubleshooting > If You Are Having Difficulty with Your Machine > Network Problems > I Want to Check that My Network Devices are Working Correctly > Check Network Devices Using the Ping Command Check Network Devices Using the Ping Command Check the IP addresses of both your computer and your Brother machine, and then confirm whether the network is operating correctly.
• My Brother Machine Cannot Print, Scan, or PC-FAX Receive over the Network 464
Home > Troubleshooting > Check the Machine Information Check the Machine Information Follow these instructions to check your Brother machine's serial number, firmware version and firmware update. 1. Press [Settings] > [All Settings] > [Machine Info.]. 2. Press one of the following options: Option Description Serial No. Check your machine's serial number. Firmware Version > Main Version Check your machine's firmware version. Firmware Update Update your machine to the latest firmware.
Home > Troubleshooting > Reset Your Brother Machine Reset Your Brother Machine 1. Press [Settings] > [All Settings] > [Initial Setup] > [Reset]. 2. Press the reset option you want to use. 3. Press [Yes] to confirm. 4. Press [Yes] for two seconds to reboot the machine.
Home > Troubleshooting > Reset Your Brother Machine > Reset Functions Reset Functions The following reset functions are available: 1. [Machine Reset] You can reset all the machine’s settings that you have changed, such as Date and Time and Ring Delay. The Demo icon will be restored to the Home screen. (MFC-J985DW in USA only) The Address Book, fax reports, and Call history will remain. 2.
Home > Routine Maintenance Routine Maintenance • Replace the Ink Cartridges • Clean Your Brother Machine • Check Your Brother Machine • Correct the Paper Feed to Clear Vertical Lines • Pack and Ship Your Brother Machine 468
Home > Routine Maintenance > Replace the Ink Cartridges Replace the Ink Cartridges Your Brother machine is equipped with an ink dot counter. The ink dot counter automatically monitors the level of ink in each of the four cartridges. When the machine detects an ink cartridge is running out of ink, the machine will display a message. The LCD displays which ink cartridge is low or needs replacing. Be sure to follow the LCD prompts to replace the ink cartridges in the correct order.
3. Open the new ink cartridge bag for the color indicated on the LCD, and take out the ink cartridge. 4. Turn the green release lever on the orange protective packing (1) counterclockwise until it clicks to release the vacuum seal. Then remove the orange protective packing as shown. IMPORTANT • DO NOT shake the ink cartridges. If your skin or clothes come into contact with the ink, wash your skin or clothes with water and soap immediately.
The machine will automatically reset the ink dot counter. • If you replaced an ink cartridge, for example, the Black cartridge, the LCD may ask you to verify that it is a brand new one (for example, [Did you change Black]). For each new cartridge you installed, select [Yes] to reset the ink dot counter for that color. If the ink cartridge you installed is not a brand new one, be sure to select [No].
Home > Routine Maintenance > Clean Your Brother Machine Clean Your Brother Machine • Clean the Scanner • Clean the Print Head from Your Brother Machine • Clean the Print Head from Your Computer (Windows®) • Clean the Print Head from Your Computer (Mac) • Clean the Machine's LCD • Clean the Outside of the Machine • Clean the Machine's Printer Platen • Clean the Paper Feed Rollers • Clean the Paper Pick-up Rollers 472
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Scanner Clean the Scanner 1. Unplug the machine from the AC power outlet. 2. Lift the document cover (1). Clean the scanner glass (2) and the white plastic (3) with a soft lint-free cloth moistened with a non‑flammable glass cleaner. 1 3 2 3. In the ADF unit, clean the white bar (1) and the glass strip (2) with a lint-free cloth moistened with a nonflammable glass cleaner.
Related Information • Clean Your Brother Machine • Telephone and Fax problems • Other Problems 474
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Print Head from Your Brother Machine Clean the Print Head from Your Brother Machine To maintain good print quality, the machine automatically cleans the print head when needed. If there is a print quality problem, start the cleaning process manually. • Clean the print head if there is a horizontal line or a blank space in the text or graphics on printed pages.
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Print Head from Your Computer (Windows®) Clean the Print Head from Your Computer (Windows®) To maintain good print quality, the machine automatically cleans the print head when needed. If there is a print quality problem, start the cleaning process manually. 1. Do one of the following: • For Windows® XP and Windows Server® 2003 Click Start > Printers and Faxes.
• Paper Handling and Printing Problems • Clean the Print Head from Your Brother Machine 477
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Print Head from Your Computer (Mac) Clean the Print Head from Your Computer (Mac) To maintain good print quality, the machine automatically cleans the print head when needed. If there is a print quality problem, start the cleaning process manually. 1. Select System Preferences from the Apple Menu. 2. Do one of the following: • (OS X v10.8.5) Select Print & Scan, and then select the machine. • (OS X v10.9.x, 10.10.
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Machine's LCD Clean the Machine's LCD IMPORTANT DO NOT use liquid cleaners (including ethanol). 1. Press and hold down to turn off the machine. The LCD displays [Shutting Down] for a few seconds before the power goes off. 2. Clean the LCD with a dry, soft lint-free cloth.
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Outside of the Machine Clean the Outside of the Machine IMPORTANT • Use neutral detergents. Cleaning with volatile liquids such as thinner or benzine will damage the outside surface of the machine. • DO NOT use cleaning materials that contain ammonia. • DO NOT use isopropyl alcohol to remove dirt from the control panel. It may crack the panel. 1. If the paper support flap is open, close it, and then close the paper support. 2.
Related Information • Clean Your Brother Machine 481
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Machine's Printer Platen Clean the Machine's Printer Platen WARNING Be sure to unplug the machine from the AC power outlet before cleaning the printer platen to avoid an electrical shock. 1. Place both hands under the plastic tabs on both sides of the machine to lift the scanner cover into the open position. 2. Clean the machine’s printer platen (1) and the area around it, wiping off scattered ink with a dry, soft lint-free cloth.
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Paper Feed Rollers Clean the Paper Feed Rollers If the paper feed rollers are stained with ink or have a buildup of paper dust, it may cause paper feed problems. 1. Unplug the machine from the AC power outlet. 2. If the paper support flap is open, close it, and then close the paper support. 3. Pull the paper tray (1) completely out of the machine. 1 4.
Related Information • Clean Your Brother Machine • Paper Handling and Printing Problems 484
Home > Routine Maintenance > Clean Your Brother Machine > Clean the Paper Pick-up Rollers Clean the Paper Pick-up Rollers Cleaning the paper pick-up rollers periodically may prevent paper jams by ensuring that paper feeds properly. 1. Unplug the machine from the AC power outlet. 2. If the paper support flap is open, close it, and then close the paper support. 3. Pull the paper tray completely out of the machine.
Home > Routine Maintenance > Check Your Brother Machine Check Your Brother Machine • Check the Print Quality • Check the Print Alignment from Your Brother Machine • Check the Ink Volume • Monitor Machine Status from Your Computer (Windows®) • Monitor Machine Status from Your Computer (Mac) 486
Home > Routine Maintenance > Check Your Brother Machine > Check the Print Quality Check the Print Quality If faded or streaked colors and text appear or if text is missing on your printouts, the print head nozzles may be clogged. Print the Print Quality Check Sheet and look at the nozzle check pattern. 1. Press [Ink] > [Improve Print Quality] > [Check Print Quality]. You can also press [Settings] > [Maintenance] > [Improve Print Quality] > [Check Print Quality]. 2. Press [Start].
When a print head nozzle is clogged, the printed sample looks like this. After the print head nozzle is cleaned, the horizontal lines are gone.
Home > Routine Maintenance > Check Your Brother Machine > Check the Print Alignment from Your Brother Machine Check the Print Alignment from Your Brother Machine If your printed text becomes blurred or images become faded after transporting the machine, adjust the print alignment. 1. Press [Ink] > [Improve Print Quality] > [Alignment]. You can also press [Settings] > [Maintenance] > [Improve Print Quality] > [Alignment]. 2. Press [Next], and then press [Start].
Home > Routine Maintenance > Check Your Brother Machine > Check the Ink Volume Check the Ink Volume Although an ink volume icon appears on the machine's LCD, you can use the ink menu to see a large graph showing the ink left in each cartridge. 1. Press [Ink] > [Ink Volume]. The touchscreen displays the ink volume. • You can also press [Settings] > [Maintenance] > [Ink Volume]. • When the ink cartridge is near the end of its life or having a problem, one of the following icons is displayed.
Home > Routine Maintenance > Check Your Brother Machine > Monitor Machine Status from Your Computer (Windows®) Monitor Machine Status from Your Computer (Windows®) The Status Monitor utility is a configurable software tool for monitoring the status of one or more devices; it allows you to get immediate notification of errors. • Do one of the following: icon in the task tray. - Double-click the - Windows® XP, Windows Vista® and Windows® 7 Click (Start) > All Programs > Brother > Brother Utilities.
• Turn Off the Show Status Monitor Feature (Windows®) • Turn Off the Status Monitor (Windows®) • Cancel a Print Job (Windows®) • Check the Ink Volume 492
Home > Routine Maintenance > Check Your Brother Machine > Monitor Machine Status from Your Computer (Windows®) > Status Monitor Indicators and What They Mean (Windows®) Status Monitor Indicators and What They Mean (Windows®) When you start up your computer, the Brother Status Monitor icon appears on the task tray. • A green icon indicates the normal stand-by condition. • A yellow icon indicates a warning. • A red icon indicates an error has occurred. • A gray icon indicates the machine is offline.
Home > Routine Maintenance > Check Your Brother Machine > Monitor Machine Status from Your Computer (Windows®) > Turn Off the Show Status Monitor Feature (Windows®) Turn Off the Show Status Monitor Feature (Windows®) The Show Status Monitor feature lets you know if there is a problem with a device that your computer is monitoring. The default setting is Only when printing from this PC. To turn it off, follow these steps: 1.
Home > Routine Maintenance > Check Your Brother Machine > Monitor Machine Status from Your Computer (Windows®) > Turn Off the Status Monitor (Windows®) Turn Off the Status Monitor (Windows®) 1. Right-click the (Brother Status Monitor) icon or window, and then select Exit. 2. Click OK.
Home > Routine Maintenance > Check Your Brother Machine > Monitor Machine Status from Your Computer (Mac) Monitor Machine Status from Your Computer (Mac) Brother's Status Monitor utility program is a configurable software tool for monitoring the status of a device and notifying you immediately in the event of an error. 1. Select System Preferences from the Apple Menu. 2. Do one of the following: • (OS X v10.8.5) Select Print & Scan, and then select the machine. • (OS X v10.9.x, 10.10.
Error icons Icon Description The ink level is low. The ink cartridge is at the end of its life. There is a problem with the ink cartridge.
Home > Routine Maintenance > Correct the Paper Feed to Clear Vertical Lines Correct the Paper Feed to Clear Vertical Lines Adjust the paper feed to reduce vertical lines. (This feature is available only for Plain paper.) 1. Press [Ink] > [Improve Print Quality] > [Correct Paper Feed]. You can also press [Settings] > [Maintenance] > [Improve Print Quality] > [Correct Paper Feed]. 2. Press the [Next] button, and then follow the instructions on the touchscreen.
Home > Routine Maintenance > Pack and Ship Your Brother Machine Pack and Ship Your Brother Machine • When you transport the machine, use the packing materials that came with your machine. If you do not pack the machine correctly, any damage that may occur in transit may not be covered by your warranty. • The machine should be adequately insured with the carrier. IMPORTANT It is important to allow the machine to “park” the print head after a print job.
2 • If you are not able to find the orange protective part, ship the machine without it. DO NOT leave the ink cartridges in the machine during shipping. 8. Wrap the machine in the bag. 9. Pack the machine and the printed materials in the original carton with the original packing material as shown below. Do not pack the used ink cartridge in the carton. If you are returning your machine to Brother as part of the Exchange Service, pack only the machine.
Related Information • Routine Maintenance • Replace the Ink Cartridges 501
Home > Machine Settings Machine Settings Customize settings and features, create shortcuts, and work with options displayed on the machine's LCD to make your Brother machine a more efficient work tool.
Home > Machine Settings > Change Machine Settings from the Control Panel Change Machine Settings from the Control Panel • In the Event of Power Failure (Memory Storage) • General Settings • Save Your Favorite Settings as a Shortcut • Print Reports • Settings and Features Tables 503
Home > Machine Settings > Change Machine Settings from the Control Panel > In the Event of Power Failure (Memory Storage) In the Event of Power Failure (Memory Storage) • Your menu settings are stored permanently and will not be lost. • Temporary settings will be lost. • The date and time and programmed fax timer jobs (for example: Delayed Fax) will be retained for approximately 24 hours. • Other fax jobs in the machine's memory will not be lost.
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings General Settings • Adjust the Machine Volume • Change for Daylight Saving Time Automatically • Set Sleep Mode Countdown • Set the Machine to Power Off Automatically • Set the Date & Time • Adjust the LCD Backlight Brightness • Change How Long the LCD Backlight Stays On • Set Your Station ID • Set Tone or Pulse Dialing Mode • Reduce Printing Noise • Change the Language Displayed on the LCD • Change the Keyboard Setti
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Adjust the Machine Volume Adjust the Machine Volume 1. Press [Settings] > [All Settings] > [General Setup] > [Volume]. 2. Press one of the following options: Option Description Ring Adjust the ring volume. Beep Adjust the volume when you press a button, make a mistake, or after you send or receive a fax. Speaker Adjust the speaker volume. 3.
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Change for Daylight Saving Time Automatically Change for Daylight Saving Time Automatically You can program the machine to change automatically for Daylight Saving Time. It will reset itself forward one hour in the spring, and backward one hour in the fall. Make sure you have set the correct date and time in the [Date & Time] setting. This feature is available only in the USA and Canada. 1. Press [Settings]. 2.
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Set Sleep Mode Countdown Set Sleep Mode Countdown The Sleep Mode (or Power Save Mode) setting can reduce power consumption. When the machine is in Sleep Mode, it acts as though it is turned off. The machine will wake up and start printing when it receives a print job or a fax. Use these instructions to set a time delay to send the machine into Sleep Mode.
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Set the Machine to Power Off Automatically Set the Machine to Power Off Automatically The Auto Power Off feature can save power consumption. Set the amount of time that the machine will be in Sleep Mode before it automatically powers off. When this feature is set to [Off], you must power off the machine manually. To turn on the machine after the Auto Power Off feature has turned it Off, press .
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Set the Date & Time Set the Date & Time The LCD displays the date and time. If they are not current, re-enter them. You can add the date and time to each fax you send by setting your Station ID. 1. Press [Settings]. 2. Press [Date & Time]. 3. Press [Date]. 4. Enter the last two digits of the year on the touchscreen, and then press [OK]. 5. Enter two digits for the month on the touchscreen, and then press [OK].
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Adjust the LCD Backlight Brightness Adjust the LCD Backlight Brightness If you are having difficulty reading the LCD, try changing the brightness setting. 1. Press [Settings] > [All Settings] > [General Setup] > [LCD Settings] > [Backlight]. 2. Press the [Light], [Med], or [Dark] option. 3. Press .
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Change How Long the LCD Backlight Stays On Change How Long the LCD Backlight Stays On You can set how long the LCD backlight stays on after the last finger press. 1. Press [Settings] > [All Settings] > [General Setup] > [LCD Settings] > [Dim Timer]. 2. Press a or b to display the [Off], [10Secs], [20Secs], or [30Secs] option, and then press the option you want. 3. Press .
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Set Your Station ID Set Your Station ID Set the machine's Station ID if you want the date and time to appear on each fax you send. 1. Press [Settings] > [All Settings] > [Initial Setup] > [Station ID]. 2. Press [Fax]. 3. Enter your fax number (up to 20 digits) on the touchscreen, and then press [OK]. 4. Press [Name]. 5. Enter your name (up to 20 characters) using the touchscreen, and then press [OK].
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Set Tone or Pulse Dialing Mode Set Tone or Pulse Dialing Mode Your Brother machine is set for a Tone dialing service. If you have a Pulse dialing (rotary) service, you must change the dialing mode. This feature is not available in some countries. 1. Press [Settings] > [All Settings] > [Initial Setup] > [Tone/Pulse]. 2. Press [Tone] or [Pulse]. 3. Press .
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Reduce Printing Noise Reduce Printing Noise The Quiet Mode setting can reduce printing noise. When Quiet Mode is turned on, the print speed becomes slower. The factory setting is [Off]. • When the Quiet Mode setting is turned on, • (MFC-J985DW in USA only) will not be displayed when 1. Press Demo is displayed on the Home screen. is displayed. [Settings] > [Quiet Mode]. 2. Press [On] or [Off]. 3. Press .
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Change the Language Displayed on the LCD Change the Language Displayed on the LCD Change the LCD language if needed. This feature is not available in some countries. 1. Press [Settings] > [All Settings] > [Initial Setup] > [Local Language]. 2. Press your language. 3. Press .
Home > Machine Settings > Change Machine Settings from the Control Panel > General Settings > Change the Keyboard Setting Change the Keyboard Setting You can choose the type of keyboard for the LCD. 1. Press [Settings] > [All Settings] > [General Setup] > [Keyboard Settings]. 2. Press [QWERTY] or [ABC]. 3. Press .
Home > Machine Settings > Change Machine Settings from the Control Panel > Save Your Favorite Settings as a Shortcut Save Your Favorite Settings as a Shortcut • Add Shortcuts • Change or Delete Shortcuts 518
Home > Machine Settings > Change Machine Settings from the Control Panel > Save Your Favorite Settings as a Shortcut > Add Shortcuts Add Shortcuts You can add the fax, copy, scan and Web Connect settings you use most frequently by saving them as your Shortcuts. Later you can recall and apply these settings instead of re-entering them. Some Shortcut menus are not available depending on your model. These instructions describe how to add a Copy Shortcut.
Home > Machine Settings > Change Machine Settings from the Control Panel > Save Your Favorite Settings as a Shortcut > Change or Delete Shortcuts Change or Delete Shortcuts You can change the settings in a Shortcut. You cannot change a Web Connect Shortcut. If you need to change a Web Connect Shortcut, delete it, and then add a new Shortcut. 1. Press [Shortcuts]. 2. Press d or c to display the Shortcut you want to change. 3. Press the Shortcut you want to change.
Home > Machine Settings > Change Machine Settings from the Control Panel > Print Reports Print Reports • Reports • Print a Report • Fax Reports • Telephone and Fax problems 521
Home > Machine Settings > Change Machine Settings from the Control Panel > Print Reports > Reports Reports The following reports are available: Transmission The Transmission prints a Transmission Verification Report for your last transmission. Address Book The Address Book report prints an alphabetical list of names and numbers stored in the Address Book memory. Fax Journal The Fax Journal prints a list of information about your last 200 incoming and outgoing faxes.
Home > Machine Settings > Change Machine Settings from the Control Panel > Print Reports > Print a Report Print a Report 1. Press [Settings] > [All Settings] > [Print Reports]. 2. Press a or b to display the report you want to print, and then press it. 3. Press [OK]. 4. Press .
Home > Machine Settings > Change Machine Settings from the Control Panel > Settings and Features Tables Settings and Features Tables • Settings Tables (2.7" Touchpanel models) • Features Tables (2.
Home > Machine Settings > Change Machine Settings from the Control Panel > Settings and Features Tables > Settings Tables (2.7" Touchpanel models) Settings Tables (2.7" Touchpanel models) These tables will help you understand your machine's menu selections and options. [Settings] Level 1 (Date & Time) Maintenance Level 2 Descriptions Date Add the date and time on the screen and in the headings of the faxes you send. Time Clock Type Select the time format from 12-hour or 24-hour.
Level 1 Level 2 Descriptions Quiet Mode - Decrease printing noise. Volume Ring Adjust the ring volume. Beep Adjust the beeper volume. Speaker Adjust the speaker volume. Backlight Adjust the brightness of the LCD backlight. Dim Timer Set how long the LCD backlight stays on after the last finger press. LCD Settings Keyboard Settings - Select the type of keyboard for the LCD. Sleep Mode - Select how long the machine must be idle before it goes into Sleep Mode.
Level 1 Level 2 Level 3 Report Setting Descriptions If you select other than Off and Every 50 Faxes, you can set the time for the option. If you select Every 7 Days, you can set the day of the week. Print Fax - - Print received faxes stored in the memory. Remote Access - - Set your own code for Remote Retrieval. Remaining Jobs - - Check which scheduled jobs are in the memory and cancel selected jobs.
Level 1 Level 2 Level 3 Descriptions WLAN TCP/IP WINS Server Specify the IP address of the primary or secondary WINS server. DNS Server Specify the IP address of the primary or secondary DNS server. APIPA Set the machine to allocate the IP address from the link-local address range automatically. IPv6 Turn the IPv6 protocol on or off for a wireless LAN. To use the IPv6 protocol, go to the Brother Solutions Center at support.brother.com for more information.
Level 1 Level 2 Level 3 Descriptions Web Connect Settings Proxy Settings User Name Change the Web connection settings. Network I/F - - Select the network connection type. Network Reset - - Restore all network settings back to the factory settings. Password [Settings] > [All Settings] > [Print Reports] Level 1 Descriptions Transmission Print a Transmission Verification Report for your last transmission. Address Book Print a list of names and numbers stored in the Address Book.
Level 1 Level 2 Reset Machine Reset Restore all the machine's settings that you have changed, such as Date and Time and Ring Delay. Local Language Descriptions Network Restore all network settings back to the factory settings. Address Book & Fax Erase all stored phone numbers and fax settings. All Settings Restore all the machine's settings back to the factory settings. - Change your LCD language. (Available only for some countries.
Home > Machine Settings > Change Machine Settings from the Control Panel > Settings and Features Tables > Features Tables (2.7" Touchpanel models) Features Tables (2.7" Touchpanel models) [Fax] (When [Fax Preview] is [Off]) Level 1 Level 2 Level 3 Descriptions - Search within the Address Book. Edit - Store Address Book numbers, set up Group numbers for Broadcasting, and change and delete Address Book numbers. - Apply Start sending a fax using the Address Book.
Level 1 Level 2 Level 3 Descriptions Options Factory Reset - Restore all settings back to the factory settings. Save as Shortcut - - Save the current settings as a shortcut. [Fax] (When [Fax Preview] is [On]) Level 1 Level 2 Sending Faxes Address Book Level 3 Level 4 Descriptions - Search within the Address Book. Edit - Store Address Book numbers, set up Group numbers for Broadcasting, and change and delete Address Book numbers. - Apply Start sending a fax using the Address Book.
Level 1 Level 2 Level 3 Sending Faxes Options Address Book Level 4 Descriptions Search within the Address Book. (Search:) Edit Received Faxes Store Address Book numbers, set up Group numbers for Broadcasting, and change and delete Address Book numbers. Set New Default - Save your settings as the default. Factory Reset - Restore all settings back to the factory settings. Save as Shortcut - - Save the current settings as a shortcut.
Level 1 Level 2 Level 3 Descriptions - Turn off or turn on 2-sided copying and select flip on long edge or flip on short edge. Advanced Settings - Select various copy settings such as Ink Save Mode or Watermark Copy. Set New Default - Save your settings as the default. Factory Reset - Restore all settings back to the factory settings. Save as Shortcut - Save the current settings as a shortcut.
Level 1 Level 2 Level 3 Level 4 Descriptions Enhance Photos Enhance Enhance Scenery Print Settings Remove Red-Eye Adjust your photos with these settings. Night Scene Fill Light Whiteboard Monochrome Sepia Auto Correct & Remove Red-Eye Crop Print Settings - Crop your photo and print a part of the image. ID Photo Print Select ID Photo Size - Print Settings Print ID photos for your resume, passport and so on.
Level 1 Level 2 Level 3 Level 4 Descriptions Add Shortcut Fax Fax Resolution - Set the resolution for outgoing faxes. (Options ) Contrast - Adjust the contrast. Broadcasting Add Number Send the same fax message to more than one fax number. Preview - Preview a fax message before you send it. Color Setting - Set whether faxes are sent in black and white or color. Real Time TX - Send a fax without using the memory.
Level 1 Level 2 Level 3 Level 4 Descriptions This list appears when each Shortcut icon is pressed for 2 seconds. Edit Shortcut Name - - Change the shortcut name. Delete - - Delete the shortcut. Edit/ Delete (Select shortcut button.) Edit Shortcut Name - Change the shortcut name. Delete - Delete the shortcut. [Ink] Level 1 Descriptions Ink Volume Check the available ink volume. Ink Cartridge Model Check your ink cartridge numbers.
Home > Machine Settings > Change Machine Settings from Your Computer Change Machine Settings from Your Computer • Change the Machine Settings Using Remote Setup • Where Can I Find My Brother Machine's Network Settings? • Network Management Software and Utilities 538
Home > Machine Settings > Change Machine Settings from Your Computer > Change the Machine Settings Using Remote Setup Change the Machine Settings Using Remote Setup The Remote Setup program lets you configure many of your Brother machine's machine settings from your computer. When you start Remote Setup, the settings on your Brother machine will be downloaded to your computer and displayed on your screen. If you change the settings on your computer, you can upload them directly to the machine.
Home > Machine Settings > Change Machine Settings from Your Computer > Change the Machine Settings Using Remote Setup > Remote Setup (Windows®) Remote Setup (Windows®) • Set Up the Brother Machine from Your Computer (Windows®) • Set Up the Brother Machine Using ControlCenter4 (Windows®) • Set Up Your Brother Address Book Using ControlCenter4 (Windows®) 540
Home > Machine Settings > Change Machine Settings from Your Computer > Change the Machine Settings Using Remote Setup > Remote Setup (Windows®) > Set Up the Brother Machine from Your Computer (Windows®) Set Up the Brother Machine from Your Computer (Windows®) 1. Do one of the following: • Windows® XP, Windows Vista® and Windows® 7 Click (Start) > All Programs > Brother > Brother Utilities. Click the drop-down list and select your model name (if not already selected).
Export Click to save the current configuration settings to a file. Click Export to save your address book or all settings for your machine. Import Click to read the settings from a file. Print Click to print the selected items on the machine. You cannot print the data until it is uploaded to the machine. Click Apply to upload the new data to the machine, and then click Print. OK Click to start uploading data to the machine, and then exit the Remote Setup Program.
Home > Machine Settings > Change Machine Settings from Your Computer > Change the Machine Settings Using Remote Setup > Remote Setup (Windows®) > Set Up the Brother Machine Using ControlCenter4 (Windows®) Set Up the Brother Machine Using ControlCenter4 (Windows®) 1. Click the (ControlCenter4) icon in the task tray, and then click Open. 2. Click the Device Settings tab. 3. Click the Remote Setup button. 4. Configure the settings as needed.
Print Click to print the selected items on the machine. You cannot print the data until it is uploaded to the machine. Click Apply to upload the new data to the machine, and then click Print. OK Click to start uploading data to the machine, and then exit the Remote Setup Program. If an error message appears, confirm that your data is correct, and then click OK. Cancel Click to exit the Remote Setup Program without uploading data to the machine.
Home > Machine Settings > Change Machine Settings from Your Computer > Change the Machine Settings Using Remote Setup > Remote Setup (Windows®) > Set Up Your Brother Address Book Using ControlCenter4 (Windows®) Set Up Your Brother Address Book Using ControlCenter4 (Windows®) Use Remote Setup through CC4 to add or change Address Book numbers on your computer. 1. Click the (ControlCenter4) icon in the task tray, and then click Open. 2. Click the Device Settings tab. 3. Click the Address Book button.
Home > Machine Settings > Change Machine Settings from Your Computer > Change the Machine Settings Using Remote Setup > Remote Setup (Mac) Remote Setup (Mac) • Set Up the Brother Machine Using ControlCenter2 (Mac) • Set Up Your Brother Address Book Using ControlCenter2 (Mac) 546
Home > Machine Settings > Change Machine Settings from Your Computer > Change the Machine Settings Using Remote Setup > Remote Setup (Mac) > Set Up the Brother Machine Using ControlCenter2 (Mac) Set Up the Brother Machine Using ControlCenter2 (Mac) 1. In the Finder menu bar, click Go > Applications > Brother, and then double-click the (ControlCenter) icon. The ControlCenter2 screen appears. 2. Click the DEVICE SETTINGS tab. 3. Click the Remote Setup button. The Remote Setup Program screen appears. 4.
Export Click to save the current configuration settings to a file. Click Export to save your address book or all settings for your machine. Import Click to read the settings from a file. Print Click to print the selected items on the machine. You cannot print the data until it is uploaded to the machine. Click Apply to upload the new data to the machine, and then click Print. OK Click to start uploading data to the machine, and then exit the Remote Setup Program.
Home > Machine Settings > Change Machine Settings from Your Computer > Change the Machine Settings Using Remote Setup > Remote Setup (Mac) > Set Up Your Brother Address Book Using ControlCenter2 (Mac) Set Up Your Brother Address Book Using ControlCenter2 (Mac) Use Remote Setup through ControlCenter2 to add or change Address Book numbers on your computer. 1. In the Finder menu bar, click Go > Applications > Brother, and then double-click the (ControlCenter) icon. The ControlCenter2 screen appears. 2.
Home > Appendix Appendix • Specifications • Enter Text on Your Brother Machine • Supply Specifications 550
Home > Appendix > Specifications Specifications General Specifications Printer Type Print Head Inkjet Black Piezo with 210 nozzles x 1 Color Piezo with 210 nozzles x 3 Memory Capacity 128 MB LCD (liquid crystal display) 1 2.7 in. (67.5 mm) TFT Color Touchscreen LCD and Touchpanel Power Source AC 100 to 120 V 50/60 Hz Power Consumption 2 Copying 3: Approx. 20 W Ready 4: Approx. 3.5 W Sleep 4: Approx. 1.3 W Power Off 4 5: Approx. 0.2 W Dimensions 8.9 in. (227 mm) 6.8 in. (172 mm) 16.5 in.
Document Size Specifications Document Size ADF Width 1 5.8 to 8.5 in. (148 to 215.9 mm) ADF Length 1 2 5.8 to 14 in. (148 to 355.6 mm) Scanner Glass Width Max. 8.5 in. (215.9 mm) Scanner Glass Length Max. 11.7 in. (297 mm) 1 ADF models only 2 Documents that are longer than 11.7 in. (297 mm) must be fed one page at a time.
Resolution 196 dpi (Color) (Vertical) Fine: 196 dpi (Black) 196 dpi (Color) Superfine: 392 dpi (Black) Photo: 196 dpi (Black) Address Book 100 names x 2 numbers Groups Up to 6 Broadcasting 250 (200 Address Book/50 Manual Dial) Automatic Redial 1 time after 5 minutes Memory Transmission Up to 200 pages 1 Out of Paper Reception Up to 200 pages 1 1 ‘Pages’ refers to the ‘ITU-T Test Chart #1’ (a typical business letter, Standard resolution, MMR code).
File Extension Media Format Image Format DPOF (ver. 1.0, ver. 1.1), Exif DCF (up to ver. 2.
1 Windows® XP in this Guide includes Windows® XP Home Edition, Windows® XP Professional, and Windows® XP Professional x64 Edition. 2 Maximum 1200 × 1200 dpi scanning with the WIA driver in Windows® XP, Windows Vista®, Windows® 7, Windows® 8 and Windows® 10 (resolution up to 19200 × 19200 dpi can be selected using the scanner utility). Printer Specifications Resolution Up to 1200 × 6000 dpi Printing Width 1 8.26 in. [8.5 in.
802.11b/ g/n Wind ows® Oper ating Syste m Windows® XP Home (SP3 or greater) 2 3 Windows® XP Professional (SP3 or greater) 2 3 Printing PC (Including Drivers) 32 bit (x86) or 150 MB 64 bit (x64) processor Fax 4 Scanning 1 GB Removable Disk (USB or Memory Card) Network Media Access (LAN) Windows Vista® 2 3 500 MB Windows® 7 2 650 MB 1.3 GB 3 Windows® 8 2 3 Windows® 8.
For the latest driver updates, visit support.brother.com and go to your model's Downloads page. All trademarks, brand and product names are the property of their respective companies.
Home > Appendix > Enter Text on Your Brother Machine Enter Text on Your Brother Machine • The characters that are available may differ depending on your country. • For touchscreen models, the keyboard layout may differ depending on the function you are setting. When you need to enter text on your Brother machine, a keyboard will appear on the touchscreen. • Press to cycle between letters, numbers and special characters. • Press to cycle between lowercase and uppercase letters.
Home > Appendix > Supply Specifications Supply Specifications Ink The machine uses individual Black, Yellow, Cyan and Magenta ink cartridges that are separate from the print head assembly. Service Life of Ink Cartridge Starter ink cartridges are included in the box with your Brother machine. The first time you install the ink cartridges, the machine will use extra ink to fill the ink delivery tubes. This is a one-time process that enables high-quality printing.
Home > Glossary Glossary This is a comprehensive list of features and terms that appear in Brother manuals. Availability of these features depends on the model you purchased.
Home > Glossary • Broadcasting C • Caller ID • Channels • CNG Tones • Coding Method • Color Enhancement • Communication Error (or Comm.
Home > Glossary • External Telephone F • F/T Ring Time • Fax Forwarding • Fax Journal • Fax Receive Code (Fax/Tel Mode Only) • Fax Storage • Fax Tones • Fax/Tel • Fine Resolution G • Gateway • Gray Scale • Group Number I • IEEE 802.
Home > Glossary • LPR M • MAC Address • MAC Address Filtering • Manual Fax • mDNS • Memory Receive N • NetBIOS Name Resolution • Network Configuration Report • Network Connection Repair Tool • Network Key • Network PC-FAX • Network PhotoCapture Center • Network Remote Setup • Network Shared Printing • Node Name O • OCR (Optical Character Recognition) • Open System • Overseas Mode P • Paging • Pause • Peer-to-Peer 563
Home > Glossary • Photo resolution (B&W only) • PhotoCapture Center • PictBridge • Ping • Polling • Protocols • Pulse R • RARP • Real Time Transmission • Remaining Jobs • Remote Access Code • Remote Retrieval Access • Remote Setup • Resolution • Ring Delay • Ring Volume S • Scanning • Search • Settings Tables • SNMP • SSID • Standard resolution • Station ID 564
Home > Glossary • Status Monitor • Subnet Mask • Super Fine resolution (B&W only) • Switching Hub T • TAD (Telephone Answering Device) • TCP/IP • Telephone Answer Code (Fax/Tel Mode only) • Temporary Settings • TKIP • Tone • Transmission • Transmission Verification Report U • User Settings List V • Vertical Pairing W • Web Services • WEP • Wi-Fi Direct® • WINS • WINS Server • Wireless LAN Access Point/Router • WLAN Report 565
Home > Glossary • WPA-PSK/WPA2-PSK Authentication Method • WPS X • Xmit Report (Transmission Verification Report) 566
Home > Glossary Ad-Hoc Mode The mode of operation in a wireless network, in which all devices (machines and computers) are connected without an access point/router. Address Book Names and numbers you have stored for easy dialing. Address Book List A listing of names and numbers stored in the Address Book memory, in alphabetical order. ADF (Automatic Document Feeder) The document can be placed in the ADF and scanned one page at a time automatically.
Home > Glossary Authentication Methods for a Personal Wireless Network A personal wireless network is a small network (such as a home wireless network) without IEEE 802.1x support. • Open system Wireless devices are allowed to access the network without any authentication. • Shared key A secret pre-determined key is shared by all devices that will access the wireless network. The Brother wireless machine uses the WEP key as the pre-determined key.
Home > Glossary BRAdmin Light (Windows®) BRAdmin Light is a utility for the initial setup of Brother network-connected devices. This utility can search for Brother products on your network, view the status and configure the basic network settings, such as IP address. Go to your model's Downloads page on the Brother Solutions Center at support.brother.com to download BRAdmin Light.
Home > Glossary Coding Method Method of coding the information contained in the document. All fax machines must use a minimum standard of Modified Huffman (MH). Your machine is capable of greater compression methods, Modified Read (MR), Modified Modified Read (MMR) and JPEG, if the receiving machine has the same capability. Color Enhancement Adjusts the color in the image for better print quality by improving sharpness, white balance and color density. Communication Error (or Comm.
Home > Glossary DNS Client The Brother print server supports the Domain Name System (DNS) client feature. This feature allows the print server to communicate with other devices using its DNS name. DNS Server The Domain Name System (DNS) is a technology to manage the names of web sites and internet domains. A DNS server allows your computer to find its IP address automatically. Domain Name Generally, in an e-mail address such as "taro@brother.co.jp", the domain name is the "brother.co.
Home > Glossary Advanced Encryption Standard (AES) provides stronger data protection using a symmetric-key encryption. • IEEE 802.11n does not support either WEP or TKIP as an encryption method. • To connect to your wireless network using IEEE 802.11n, we recommend selecting AES. Extension Telephone A telephone on the fax number that is plugged into a separate telephone wall jack. External Telephone A telephone that is plugged into the EXT jack of your machine.
Home > Glossary Gateway A gateway is a network point that acts as an entrance to another network and sends data transmitted via the network to an exact destination. The router knows where to direct data that arrives at the gateway. If a destination is located on an external network, the router transmits data to the external network. If your network communicates with other networks, you may need to configure the Gateway IP address.
Home > Glossary Journal Period The pre-programmed time period between automatically printed Fax Journal Reports. You can print the Fax Journal on demand without interrupting the cycle. LAN The acronym for Local Area Network. Refers to a network of computers that are located in the same building, on the same floor, and so on, and are connected using an Ethernet or other connection method. This type of network is considered a closed network.
Home > Glossary NetBIOS Name Resolution Network Basic Input/Output System (NetBIOS) name resolution enables you to obtain the IP address of the other device using its NetBIOS name during the network connection. Network Configuration Report The Network Configuration Report prints a report listing the current network configuration, including the network print server settings.
Home > Glossary Network Remote Setup The Remote Setup software allows you to configure network settings from either a Windows® or Mac computer. Network Shared Printing Network Shared Printing is a type of printing in a network shared environment. In a network shared environment, each computer sends data via a server or print server. Node Name The Node Name is a machine name on the network.
Home > Glossary Photo resolution (B&W only) A resolution setting that uses varying shades of gray for the best representation of photographs. PhotoCapture Center Use Brother's PhotoCapture Center to view, retrieve and save data from a USB flash drive or a media card inserted into the Brother machine. For Windows®, select the Photo tab in ControlCenter4. PictBridge Allows you to print photos directly from your digital camera at high resolution for photo quality printing.
Home > Glossary Remote Access Code Your own four-digit code (– – –*) that allows you to call and access your machine from a remote location. Remote Retrieval Access The ability to access your machine remotely from a touch tone telephone. Remote Setup The Remote Setup program lets you configure many machine and network settings from a computer application. When you start this application, the settings on your machine will be downloaded automatically to your computer and displayed on your computer screen.
Home > Glossary wireless network devices regularly send wireless packets (referred to as beacons), which contain the SSID information. When your wireless network device receives a beacon, you can identify the wireless network that is close enough for the radio waves to reach your device. Standard resolution 203 × 98 dpi (black and white). 203 × 196 dpi (color). It is used for regular sized text and the quickest transmission. Station ID The stored information that appears on the top of faxed pages.
Home > Glossary TAD (Telephone Answering Device) You can connect an external device or answering machine to the EXT. jack of your machine. TCP/IP Transmission Control Protocol/Internet Protocol (TCP/IP) is the most popular set of protocols used for communication, such as Internet and email. This protocol can be used in almost all operating systems, including Windows®, Windows Server®, OS X and Linux®. Telephone Answer Code (Fax/Tel Mode only) When the machine answers a voice call, it pseudo/double-rings.
Home > Glossary Web Services The Web Services protocol enables Windows Vista®, Windows® 7, Windows® 8, or Windows® 10 users to install the drivers used for printing and scanning by using the machine icon in the Network folder. Web Services also lets you check the current status of the machine from your computer. WEP Wired Equivalent Privacy (WEP) is one of the encryption methods used in a wireless network. When using WEP, the data is transmitted and received with a secure key.
Home > Glossary Xmit Report (Transmission Verification Report) A listing for each transmission, that shows its date, time and number.
Brother International Corporation 200 Crossing Boulevard P.O. Box 6911 Bridgewater, NJ 08807-0911 USA Brother International Corporation (Canada) Ltd. 1 rue Hôtel de Ville, Dollard-des-Ormeaux, QC, Canada H9B 3H6 Visit us on the World Wide Web www.brother.
