User’s Guide General Description Operating Procedures Appendix, etc. MW-100 Mobile Printer l Before using this printer, be sure to read this User’s Guide. l We suggest that you keep this manual in a handy place for future reference.
Introduction Introduction Thank you for purchasing the MPrint MW-100 (hereafter referred to as “the printer”). This monochrome thermal mobile printer is ultra-portable and can be connected to a Pocket PC (PDA running Pocket PC) or a computer to make quick printouts. This User’s Guide contains operating precautions and instructions. Before using this printer, be sure to read this manual for information on its correct operation.
! The contents of this manual are subject to change without notice. ! The contents of this manual may not be duplicated or repro- duced, partially or in full, without permission. ! Please note that we assume no responsibility for damages arising from earthquakes, fire, other disasters, actions of third parties, the user’s intentional or negligent operation, misuse or operation under other special conditions.
Precautions Precautions Precautions indicated as shown below contain important safety information and should be strictly observed. If the printer malfunctions, immediately stop using it, and then contact the sales representative where it was purchased. The meanings for marks used in this manual are described below. Warning Caution Failure to observe instructions marked with this symbol may result in death or serious injuries.
Indicates an action that must be performed Indicates that the power supply cord must be unplugged from the electrical outlet iv
Precautions Concerning this printer (including the built-in lithium ion battery) Warning ! Do not use this printer wherever it is prohibited, for example, on an airplane, otherwise it may affect equipment, resulting in an accident. ! If this printer is to be used in special environments, for example, near medical equipment, make sure in advance that there would be no harmful effects from electromagnetic waves.
Warning ! Liquid leaking from the printer may indicate that the built-in battery is damaged. Immediately move the printer away from flames, otherwise a fire may result. In addition, do not touch the leaking liquid. This liquid may damage your eyes or skin if brought in contact with them. If the liquid makes contact with your eyes, immediately rinse them with water and consult a medical professional. If the liquid makes contact with your skin or clothing, immediately rinse them with water.
Precautions Warning ! If the printer is not fully charged after the specified amount of time has passed, stop charging it, otherwise fire, electric shock or damage may result. Caution ! Keep the printer out of the reach of children, particularly infants, otherwise injuries may result. ! Stop operating the printer if it leaks or becomes discolored, deformed or otherwise defective.
Concerning the AC adapter Warning ! Only use the AC adapter designed specifically for this printer, otherwise fire, electric shock or damage may result. ! Do not plug the printer into an electrical outlet other than a household outlet (AC 100 V – 240 V), otherwise fire, electric shock or damage may result. ! Do not touch the AC adapter or the power supply plug with wet hands, otherwise electric shock may occur.
Precautions Warning ! When unplugging the power supply cord, do not pull on the cord, otherwise fire or electric shock may result. ! Do not insert foreign objects into the terminals of the AC adapter, otherwise burns or electric shock may result. ! Incorrectly using the AC adapter may result in fire or electric shock. Therefore, observe the following precautions. ! Do not damage it. ! Do not modify it. ! Do not twist it. ! Do not severely bend it. ! Do not pull on it. ! Do not place objects on it.
Warning ! If the printer is not to be used for a long period of time, be sure to unplug the AC adapter from the unit and the electrical outlet for safety reasons. ! Do not wind the AC adapter cable around the adapter or bend the cable, otherwise the cable may be damaged.
Precautions Operating precautions " Operate this printer in an environment that meets the following requirements. ! Temperature: 0 – 40 °C ! Humidity: 20 – 80 % (Maximum wet-bulb temperature: 27 °C) ! Do not operate or store this printer in a location exposed to extremely high or extremely low temperatures, extreme humidity, extreme dust, or extreme vibrations, otherwise the printer may be damaged or malfunction.
" Concerning the paper cassette and the handling of the paper ! Store the paper cassette away from extremely hot, extremely humid or extremely dusty locations and out of direct sunlight, otherwise the paper may become discolored or a malfunction may result. ! Be sure to close the lid of the paper cassette before storing it, otherwise the paper may become discolored. ! Do not leave paper cassettes in a closed car under a hot sun, otherwise they may become discolored.
Precautions ! Depending on the environmental conditions of the location and the quality of the material that the adhesive-backed paper is attached to, the adhesive-backed paper may become discolored, peel off, be difficult to remove, leave adhesive behind or damage the surface that it was affixed to. Before using the adhesive-backed paper, test it by affixing a small piece to an inconspicuous area of the intended surface. ! Do not affix the adhesive-backed paper to people, animals or plants.
xiv
CONTENTS CONTENTS Introduction .......................................................... i Precautions ......................................................... iii Operating precautions .............................................. xi CONTENTS ........................................................... 1 General Description ............................................ 2 Operating Procedures ......................................... 3 Charging ............................................................
1 General Description Right side Paper cassette cover Paper check window IrDA infrared port Paper output slot Left side Status indicator light Charging indicator light Power button USB port AC adapter connector 2
Operating Procedures 2 Operating Procedures Charging This printer is equipped with a built-in lithium ion battery. Use the AC adapter designed specifically for this printer to charge the battery. After purchasing this printer, be sure to charge the battery fully before using it. 1 Plug the AC adapter cable into the AC adapter connector on the printer. 2 Plug the AC adapter plug into a household electrical outlet (AC 100 V – 240 V). Charging of the built-in lithium ion battery automatically begins.
• In order to protect the circuitry, the battery cannot be charged if the unit is in a location exposed to extremely high or extremely low temperatures. • Do not wind the AC adapter cable around the adapter or bend the cable, otherwise the cable may be damaged. • It takes approximately three hours for the battery to be recharged from completely empty to fully charged (with the printer turned off).
Operating Procedures Turning on the printer 1 Press and hold the power button for a short while, until the green status indicator light illuminates. If the power button is pressed again, the printer is turned off. • In order to prevent this printer from accidentally being turned on, it will not come on if the power button is lightly pressed. Therefore, if the printer does not come on, hold the power button pressed for a little while.
Preparing the paper Use only the paper cassette designed exclusively for this printer. Use of any other paper will result in damage. To prepare the paper cassette Prepare the paper cassette before installing it into the printer. • Be careful not to drop any paper while the paper cassette is being prepared. 1 Open the lid of the Lid paper cassette, and then tear off the two pieces (1) on the sides. Paper cassette 2 Firmly fold the lid back along the fold (2).
Operating Procedures " Handling the paper cassette ! This printer determines the paper type depending on the installed paper cassette, then automatically selects the settings appropriate for that type of paper. Do not transfer paper to a different paper cassette. ! Do not try to reuse paper that has already passed through the printer. ! The paper cassette is made of cardboard. After all of the paper is used, dispose of the cassette according to local regulations.
Installing the paper cassette 1 Slide the paper cassette cover (on the top of the printer) in direction 1. → The paper cassette cover will open in the direction indicated by 2. 2 Insert the paper cassette. Paper type indication The paper type indication on the paper cassette should face up. The end of the paper should point toward you. • When loading the paper cassette, make sure that it is correctly aligned and that the end of the paper is not folded, otherwise a paper misfeed may result.
Operating Procedures 3 Close the paper cassette cover in direction 3. 4 Slide the paper cassette Paper check window cover in direction 4. If the paper cassette is correctly loaded, the paper type indication on the cassette can be seen through the paper check window, and the paper cassette cover will be locked. Paper type indication • Do not remove the paper from the paper cassette and load it directly into the printer. • To change the paper type, install a different paper cassette.
Sending data from a Pocket PC or computer In order use this printer to print data from a Pocket PC (PDA running Pocket PC) or computer, the software must first be installed onto the Pocket PC or computer as described in the ‘software guide’ supplied with the printer. Sending data through an IrDA connection A Pocket PC can communicate with this printer through its IrDA infrared port.
Operating Procedures Sending data through a USB connection Using the enclosed USB cable, this printer can be connected to a computer or a Pocket PC supporting a USB host interface.
Feeding paper If a paper misfeed occurs, remove the paper according to the following procedure. If the paper has fed out of the paper output slot: 1 Pull the paper out from the paper output slot. • When pulling out the paper, be sure not to tear it. If the paper has not fed out of the paper output slot: 1 Open the paper cassette cover. 2 Remove the paper cassette. 3 Pull out the misfed paper. • When pulling out the paper, be sure not to tear it.
Operating Procedures Maintenance ! Be sure to turn off the printer before cleaning it. Cleaning the printer Clean the front of the printer. 1 Clean off any dust or other dirt from the printer by wiping it with a soft, dry cloth. If the printer is extremely dirty, wipe it with a slightly damp cloth. ! Do not use benzene or paint thinners, otherwise the printer may become discolored or deformed.
Cleaning the pick-up roller If the pick-up roller is dirty, paper may not be fed correctly. 1 Affix a piece of cellophane Pick-up roller tape to the pick-up roller. 2 Remove the cellophane tape from the pick-up roller. Cellophane tape → Any dirt on the pick-up roller is removed with the tape. Rotate the pick-up roller and repeat the procedure to clean the entire surface of the roller.
Operating Procedures Disposing of this printer Before disposing of this printer, be sure to remove the built-in lithium ion battery. Removing the lithium ion battery 1 Turn off the printer, and then disconnect the AC adapter. 2 Using a screwdriver, loosen the four screws at the back of the printer, and then remove the back cover. Lithium ion battery Connector 3 Disconnect the connector, and then remove the lithium ion battery. • Removing the back cover will void the warranty.
3 Appendix Product specifications Printer specifications Status indicator light (red/green) Charging indicator light (orange) Direct thermal printing with a line thermal Method print head Resolution 300 dpi × 300 dpi 15 seconds/sheet Print speed (standard text on thermal paper with 7 % coverage at an ambient temperature of 25 °C) No.
Appendix Troubleshooting Symptoms & remedies Symptom: The printer Remedy: Press and hold the power button cannot be turned on. for a short while. (→ Refer to page 5.) Remedy: The built-in lithium ion battery needs recharging. (→ Refer to page 3.) Symptom: Although the With an IrDA connection: print command was Remedy: Make sure that there is no issued, the printer obstacle between this printer and the does not print. PDA, and check that they are within 20 cm of each other. (→ Refer page 10.
Symptom: The paper does not feed. Remedy: Make sure that the lid of the paper cassette is firmly folded along the fold (2). (→ Refer to page 6.) Remedy: Make sure that the paper cassette cover is securely closed. (→ Refer to page 9.) Remedy: The paper may be dirty. Pull out the first sheet from the back of the paper cassette, and then install the paper cassette again. (→ Refer to pages 6 and 8.) Remedy: Clean the pick-up roller. (→ Refer to page 14.) Symptom: The print is faint (light).
Appendix Symptom: The paper cassette cover cannot be closed. Remedy: The parts indicated by “A” in the illustration below have locked up. Refer to the illustration and use the tip of a ball-point pen to slide the indicated part in the direction of the arrow to free it. Paper cassette cover A Push with the tip of a ball-point pen to slide it.
Indicator lights " Status indicator light A green light indicates the printer is operating correctly, while red indicates an error has occurred. Indicator light color Green Red Indicator light status Constantly lit Flashing Flashing Constantly lit Printer status Waiting to receive data Receiving data An error has occurred. A system error has occurred. If an error has occurred, check for the following causes. Error description Remedy There is no paper cassette installed.
Appendix " Charging indicator light With the charging indicator light, the status of the power supply can be checked. The charging indicator light has two functions.
MW-100 Accessories Stock No. Description C-11 A7 Thermal paper (105 mm x 74 mm) C-21 A7 Label (105 mm x 74 mm) C-41 A7 Cut label sheet (4/sheet) (26.25 mm x 74 mm) C-42 A7 Cut label sheet (2/sheet) (52.
