Product Safety Guide QL-800/QL-810W/QL-820NWB Read the whole guide before using your product and keep it for later reference.
Introduction The documentation included with the Label Printer, including the Product Safety Guide (this guide) and the Quick Setup Guide (printed) contains operating precautions and basic instructions. For more information, and for information about software and using the Label Printer on a network, see the User’s Guide, which can be found on your model's Manuals page on the Brother Solutions Center at support.brother.com.
To use your Label Printer safely If your Label Printer malfunctions, immediately stop using it, and then contact the sales representative where your Label Printer was purchased. Symbols used in this document The following symbols are used throughout this document: DANGER Indicates an imminently hazardous situation which, if the product is handled without following the warnings and instructions, will likely result in death or serious injuries.
Important safety instructions English DANGER Battery Unit (Rechargeable Li-ion Battery included) (Optional: QL-810W/820NWB only) DO NOT leave a drained Battery Unit in your Label Printer for a long period of time. This could shorten the life of the Battery Unit. DO NOT use or leave the Battery Unit near a fire, heaters, or other high temperature (above 176F/80C) locations.
WARNING Battery Unit (Rechargeable Li-ion Battery included) (Optional: QL-810W/820NWB only) DO NOT operate, charge, or store your Battery Unit in the following locations, otherwise fire, electrical shock, or damage may occur: Near water, such as in a bathroom or near a water heater, or in an extremely humid location In a location where it is exposed to rain or moisture In an extremely dusty location In an extremely hot location, such as near open flames, heaters, or in direct sunlight In a closed
English WARNING DO NOT allow the charging contacts or the surrounding areas to become dirty, or to come into contact with foreign objects. There is a risk of burns and damage. DO NOT touch the terminal with wet hands, otherwise electrical shock, equipment damage, ignition or smoking may occur. When not attached to the Label Printer for use, cover the terminal with tape, etc. to prevent intrusion of foreign material such as dust. Also, do not use if the terminal is soiled with dust, etc.
WARNING Use the AC Adapter, AC Power Cord, or cable correctly and observe the following precautions, otherwise a fire or electrical shock may occur: DO NOT damage the AC Adapter, AC Power Cord, or cable. DO NOT modify the AC Adapter, AC Power Cord, or cable. DO NOT twist the AC Adapter, AC Power Cord, or cable. DO NOT severely bend the AC Adapter, AC Power Cord, or cable. DO NOT pull on the AC Adapter, AC Power Cord, or cable. DO NOT place objects on the AC Adapter, AC Power Cord, or cable.
English CAUTION Label Printer Keep out of the reach of children, particularly infants, otherwise injury may occur. Stop operating your Label Printer if it leaks or becomes discolored, deformed, or otherwise defective. DO NOT hold your Label Printer by the DK Roll Compartment Cover. There is a risk of injury if the cover detaches and your Label Printer falls. When connecting cables and accessories, make sure you connect them correctly and in the correct order.
General Precautions Label Printer If the Bluetooth function and wireless LAN function are both turned on, the communication speed may decrease due to radio wave interference. If this occurs, turn off the function that you are not using (Bluetooth function or wireless LAN function). DO NOT cover or insert foreign objects into the Label Output Slot, AC connector, or USB Port. When not used for an extended period, remove the DK Roll from the Label Printer.
Compilation and Publication Notice Trademarks BROTHER is either a trademark or a registered trademark of Brother Industries, Ltd. © 2016 Brother Industries, Ltd. All rights reserved. Microsoft, Windows, Windows Vista and Windows Server are registered trademarks of Microsoft Corporation in the United States and other countries. Apple, Macintosh, Mac OS, Safari, iPad, iPhone and iPod touch are trademarks of Apple Inc., registered in the United States and other countries.
Open Source Licensing Remarks (QL-810W/820NWB) This product includes open-source software. To see the open source licensing remarks, go to the manual download selection on your model’s home page of Brother Solutions Center at support.brother.com. Regulation for QL-800/QL-810W/QL-820NWB CAUTION (QL-810W/QL-820NWB only) RISK OF EXPLOSION IF BATTERY IS REPLACED WITH AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Industry Canada Compliance Statement (For Canada only) This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
D00RAG001 Printed in China Imprimé en Chine Impreso en China
