Instruction Manual for Foil Transfer Starter Kit

ManualsBrandsBrother ManualsOffice SuppliesScanNCut DX Electronic Cutting Machine with 5 in. LCD Touch Screen, Grey

Table Of Contents

You can create high-quality designs by using the pressing tool to apply foil with your cutting machine.

WARNING

CHOKING HAZARD.

• This product contains many small parts. This product is not intended for use by children of any age. Keep product out of the reach of

children or else choking or other injury may result.

CAUTION

CHOKING OR OTHER INJURY

• Do not put the foil transfer sheet or glue from the glue pen in your mouth as choking or injury may result.

● Do not insert any object other than the glue pen or pressing tool into the glue pen holder.

● Use paper with a smooth surface. Foil cannot be applied to material that is very absorbent, such as fabric, or has an extremely

rough surface or a coated surface.

● When applying foil, only use paper with a thickness of 0.5 mm or less.

● If the adhesive strength of the dust removal sheet has decreased, lightly wipe the sheet with a wet wipe, to remove any dust or dirt.

After wiping the sheet, be sure to allow it to dry.

● If the excess foil can no longer be attached to the dust removal sheet, replace the sheet with a new one.

● Do not fold or bend the protective sheet.

● If the protective sheet becomes dirty or damaged, replace it with a new one, otherwise foil may not be correctly applied.

● Do not store the glue pen, foil transfer sheet or dust removal sheet in a location exposed to direct sunlight, high temperatures or

high humidity. In addition, be sure to place the cap on the glue pen after using it.

● Use in an environment between 5 °C and 35 °C (41 °F and 95 °F).

● The 12" × 24" (305 mm × 610 mm) cutting mat cannot be used.

● For detailed instructions on using the cutting machine, refer to the Operation Manual supplied with it.

● The contents of this document are subject to change without notice.

● The screens in this manual are for illustration purposes only and may differ from the actual screens.

Foil Transfer Starter Kit

About the Foil Transfer Starter Kit

Important Safety Instructions

Precautions

Version 0

Summary of content (7 pages)

PAGE 1
EN Foil Transfer Starter Kit About the Foil Transfer Starter Kit You can create high-quality designs by using the pressing tool to apply foil with your cutting machine. Important Safety Instructions WARNING CHOKING HAZARD. • This product contains many small parts. This product is not intended for use by children of any age. Keep product out of the reach of children or else choking or other injury may result.
PAGE 2
Accessories After purchasing this kit, check the contents. A B C D E F G H Name A Glue pen holder B Pressing tool C Glue pen *1 D Foil transfer sheets 3.9" × 7.8" (100 mm × 200 mm) (gold and silver) *1 E Protective sheet 8.6" × 12" (220 mm × 305 mm) *1 F Dust removal sheet 1.9" × 2.9" (50 mm × 75 mm) (with storage sheet) *1 G Activation card for access to 50 foiling patterns H Insertion *1 These accessories are consumables.
PAGE 3
Activating the Foiling function CanvasWorkspace has a large variety of foiling patterns that can be used immediately. Activating Foiling Patterns on CanvasWorkspace a Activating the Foiling Function on the Machine a Touch "Premium Functions" on the settings screen. b Select "ON" beside "Kit Activation (Foil)". Using a computer, log in to CanvasWorkspace. (http://CanvasWorkspace.Brother.com) • New users should create a free account. b Click c Click .
PAGE 4
Retrieving the Foiling Pattern on the Machine For detailed instructions on using the cutting machine, refer to the Operation Manual supplied with it. a Attach the material (to which the foil is to be applied) to the low tack adhesive mat, and then load the mat. c • Good foiling results may be difficult to achieve with extremely small or complicated patterns. • If a highly adhesive mat is used, the material may be damaged when it is peeled off.
PAGE 5
e Touch to scan the material. Position the pattern so it does not extend from the material and the foil. h Check the amount of glue remaining in the glue pen. Set the scale on the "Glue Pen Scale" confirmation screen to match the remaining amount of glue. • Make sure that the pattern is smaller than the foil (3.9" × 7.8" (100 mm × 200 mm)). • Before using the glue pen, make sure that the resin ball is removed from the tip of the glue pen.
PAGE 6
k Touch the "Start" key to start applying glue. m Select "Foil 2 (Foil)". • If the “Scale on Glue Pen” setting value is large, the pen may move slowly and produce an unusual, loud operating sound. • While glue is being applied, do not pause the operation or change any settings, such as the amount of glue remaining in the pen. Otherwise, thicker lines may be produced. • The paper may tear if the gluing pressure is too strong. Before using thin paper, decrease the pressure.
PAGE 7
o p Remove the glue pen holder from the carriage, and then remove the glue pen. Attach the pressing tool to the tip of the glue pen holder, and then insert the holder into the carriage. s Repeatedly dab the top of the foil with the dust removal sheet to remove any excess foil. • Do not rub the foil with the dust removal sheet, otherwise the foil may become damaged. • For storage, attach the dust removal sheet to its storage sheet in order to prevent it from being lost.