Quick Reference Guide

ManualsBrandsBrother ManualsCutting MachineSDX230D

Be sure to rst read the “Important Safety Instructions” in the Product Safety Guide.

This Quick Reference Guide contains basic instructions and information for your Brother machine.

Store this Quick Reference Guide in a safe place, where it can be easily accessed for future reference.

Refer to the Operation Manual for detailed instructions.

The Operation Manual as well as other instructions can be downloaded

from the Brother Solutions Center (http://s.brother/cmoae/).

'/<

Mat (for ScanNCut DX)

* When cutting paper with

a smooth surface

Sheet for fabric cutting Auto blade holder

Standard Tack

Adhesive Mat

Low Tack

Adhesive Mat

Iron-on Fabric

Appliqué Contact

Sheet

(White Backing)

High Tack

Adhesive Fabric

Support Sheet

Auto Blade

(Black)

Thin Fabric Auto

Blade (Beige)

Material Thichkness

Paper

Printer paper 80 g/m² (0.1 mm)

Scrapbook paper (thin) 120 g/m² (0.15 mm)

Scrapbook paper (medium-thick)

200 g/m² (0.25 mm)

Cardstock 280 g/m² (0.35 mm)

Vellum, tracing paper 0.07 mm

Poster board 400 g/m² (0.5 mm)

Fabric

Thin cotton fabric (for quilt piece) 0.25 mm

Thin cotton fabric (except for quilt piece) 0.25 mm

Flannel (for quilt piece) 0.5 mm

Flannel (except for quilt piece) 0.5 mm

Felt 3 mm

Denim 14 oz 0.75 mm

Others

Plastic sheet (PP) 0.2 mm

Vinyl 0.2 mm

Magnet 0.3 mm

Sticker or seal 0.2 mm

Foam sheet 3 mm

Attach the Material to the Mat

Install the Holder

Select the Pattern

Note

● Craft paper or fabric covered with decorative layer (that can easily separate) such as lamé or foil is not recommended for use. If such media is used or tested

it is recommended to clean the scanner glass inside the machine after every use.

Make sure that the arrow

is facing the machine

feeder (top side up).

Remove the

protective cap.

Select “Pattern”.

Peel off the protective

sheet.

*Keep the protective sheet for

storage use.

Turn on the machine.Connect the power

cord to the machine,

and then open the

front tray cover.

Pull out the rear tray.

Select your choice of

pattern category.

Before attaching your choice

of material onto the mat, check

if the strength of the adhesive

is suitable by test attaching the

material onto the edge of the

adhesive side of the mat.

Select your choice of

pattern.

If the adhesive is ok,

attach the material onto

the mat’s adhesive.

Hold the blade holder

and then install it in the

carriage with the Brother

Logo facing you.

Check the pattern size and

number of pattern(s), and

then touch the “Set” key.

Apply some pressure to

rmly attach the material

onto the mat.

Press down the

holder lock lever.

Check the pattern(s)

placement, and then

touch the “OK” key.

STEP 2

STEP 3

STEP 4

Mat and Blade Selection

STEP 1

Prepare the material to be cut. Referring to the following table,

select a mat and blade appropriate

for the material.

1 2

Memo

● An auto blade holder is included with this machine. Using the auto blade

holder, the thickness of the material is detected, and the blade extension

automatically adjusts based on the material’s thickness.

● Use the mat designed specically for ScanNCut DX.

● Depending on your machine model, some accessories may not be

included. Additional purchase may be required.

Load the Mat and Start Cutting

Load the mat (arrow

facing up).

Touch the “Start” key to

start cutting.

When cutting is nished,

touch the “OK” key on

the screen.

Press the “Feed” button

in the operation panel to

release the mat.

Touch “Please select” key then select “Cut” in the

preview screen.

Peel off the material. Use the spatula to peel off

the cutout pattern.

*After using a mat, cover it with the protective sheet.

STEP 5

421

5 76 8

Note

● We recommend performing “Test/Trial Cut” before cutting your project. Please refer to “Test/Trial Cut (For Desired Cutting Results)” on the next page.

IMPORTANT

For smooth feeding, align the

top of the mat with the guides

on the right and left sides

of the feed slot and insert it

under the feed rollers.

Lightly place your hand on

the center of the mat and

gently push it forward while

pressing the “Feed” button

on the operation panel.

*1: Fabric Mat (CADXMATF12) can be used instead of the Standard Tack Adhesive Mat and the High Tack Adhesive Fabric Support Sheet.

*2: Vinyl Auto Blade Holder included in Vinyl Auto Blade Kit (CADXVBKIT1) and Disney Vinyl Auto Blade Kit (CADXVBDSNKIT1) is also recommended.



Fabric Cutting Basics

Iron-On Fabric Appliqué Contact Sheet

● Reinforces the fabric so that various patterns can be cut out.

● Original texture may change because it remains attached to the back of the fabric.

Use the standard mat. Do not place fabric with an iron-on fabric appliqué contact sheet

attached to the back directly onto a mat with a high tack adhesive fabric support sheet

attached.

High Tack Adhesive Fabric Support Sheet

● By attaching this adhesive sheet to the standard mat, the adhesive strength of the mat will

increase.

● Cut results may vary depending on the shape of the selected pattern.

Fabric Mat

● With this mat, High Tack Adhesive Fabric Support Sheet is not required.

Refer to the “Mat and Blade Selection” table, and

use an iron-on fabric appliqué contact sheet, a

high tack adhesive fabric support sheet or fabric

mat to cut fabric. Refer to the instructions included

with the iron-on fabric appliqué contact sheet, high

tack adhesive fabric support sheet or fabric mat

for details. If these accessories are not included

with your machine, purchase the optional iron-on

fabric appliqué contact sheet (CASTBL1), high tack

adhesive fabric support sheet (CASTBL2) or fabric

mat (CADXMATF12). Some optional accessories

may not be available in other countries.

Summary of content (2 pages)

PAGE 1
Quick Reference Guide IMPORTANT ' /< EN Be sure to first read the “Important Safety Instructions” in the Product Safety Guide. This Quick Reference Guide contains basic instructions and information for your Brother machine. Store this Quick Reference Guide in a safe place, where it can be easily accessed for future reference. Mat and Blade Selection 1 2 Prepare the material to be cut. Memo ●● An Referring to the following table, select a mat and blade appropriate for the material.
PAGE 2
Scanning Functions Scan an illustration, photo or your own drawing to create personalized cut designs. The design can then be cut out or saved as data. Direct Cut Scan to Cutting Data An original illustration can be scanned and its outline can be cut out. An original illustration can be scanned, converted to cutting lines for cutting/ drawing with this machine, then saved as data. * Refer to the Operation Manual for detailed instructions. 2 Select “Scan”.