Instruction Manual for Embossing Tool Set

ManualsBrandsBrother ManualsCraft MachinesScanNCut DX Electronic Cutting Machine with Built-in Scanner - Sky Blue

Table Of Contents

By using the embossing tools with the cutting machine, you can create embossing by pressing a pattern into the material* for either a

recessed effect or, by flipping over the material, a raised effect.

Use this kit to create custom embossed projects.

* Use paper and metal sheet only for the material.

● For details on the region embossing procedure, refer to “Consumables & Options” at the Brother Solutions Center

(http://s.brother/ccoab/).

● The following optional accessories will be necessary for region embossing.

- Embossing template sheets (CAEBSTS1) (F)

- Scanning support sheet (CASTCL1 (stencil sheet)) (G)

● Use the embossing mat when you emboss. Embossing mat can be purchased separately. CAEBSMAT1(embossing mat) (D)

● When embossing metal sheets, be sure to use genuine Brother metal sheets. Metal sheets can be purchased as optional

accessories. CAEBSSMS1 (embossing silver metal sheets) or CAEBSBMS1 (embossing brass metal sheets). (E)

● Do not insert any object other than the embossing tools into the embossing tool holder.

● Do not cut while using the embossing mat.

● If the adhesive strength of the embossing mat is reduced, lightly wipe it with a wet wipe (recommended to use an alcohol-free wet

wipe), to remove any dust or dirt. After wiping the mat, be sure to allow it to dry. If the mat becomes wet, its surface will become

brittle.

● If material can no longer be attached to the embossing mat, replace the mat with a new one.

● Without peeling the embossing mat off the cutting mat, affix the protective sheet for the cutting mat before storing the mats.

● Do not store in a location exposed to direct sunlight, high temperatures or high humidity.

● Use in an environment between 10 °C and 35 °C (50 °F and 95 °F).

● For detailed instructions on using the cutting machine, refer to the Operation Manual supplied with it.

● The contents of this document are subject to change without notice.

● The screens in this manual are for illustration purposes only and may differ from the actual screens.

Embossing Tool Set

About the Embossing Tool Set

About region embossing

Precautions

Version 0

Summary of content (5 pages)

PAGE 1
EN Embossing Tool Set About the Embossing Tool Set By using the embossing tools with the cutting machine, you can create embossing by pressing a pattern into the material* for either a recessed effect or, by flipping over the material, a raised effect. Use this kit to create custom embossed projects. * Use paper and metal sheet only for the material. About region embossing ● ● For details on the region embossing procedure, refer to “Consumables & Options” at the Brother Solutions Center (http://s.
PAGE 2
Accessories After purchasing this kit, check the contents. A B C Name A Embossing tool holder B Embossing tools (diameter 1.5 mm and 3 mm) C Insertion The following are available as optional accessories to be purchased separately. For purchase options, contact the retailer where this set was purchased. D E F G Name D Embossing mat 12" × 9.5" (305 mm × 241 mm) * E Metal sheets with self-adhesive protective sheets (silver and brass color) 7.9" × 6.1" (200 mm × 155 mm) (thickness 0.
PAGE 3
Line embossing In this manual, the embossing effect created using the lines of a pattern is called line embossing. ■ Precautions c • With line embossing, only use paper with a thickness of 0.5 mm or less or metal sheets with a thickness of 0.2 mm or less. • The procedure for metal sheets uses genuine Brother metal sheets. a Set the elevation lever on the left side of the machine to the "2" position.
PAGE 4
e Remove the embossing tool holder cap. Select the embossing tool according to the line thickness that you want to emboss, and then insert the embossing tool into the embossing tool holder so that  on the tool aligns with  on the holder. After securing the holder cap, insert the holder into the cartridge. • Before inserting the holder into the cartridge, check if the tool moves up and down in the holder. If the tool moves, remove the cap, and then attach it again.
PAGE 5
h Touch the "Test" key to make a trial embossing. Check the result of the test embossing, and if there are no problems, touch the "Start" key. • If the desired embossing effect is not achieved, adjust the embossing pressure. The embossing effect differs depending on the type and thickness of the material. • Some materials may tear if the embossing pressure is too strong or the embossing speed is too fast. Troubleshooting 1. Embossing is not clear.