Brochure

52
®
TC Gripbelt
®
SheaveswithBrowningSplitTaper
®
Bushings
ForUsewithAll“C”SectionBelts
TableNo.1 Specications-Stock“TC”Sheaves
TableNo.3 BushingDimensions
TableNo.2StandardKeyseats
1 3/8” bore bushings also available with
3/8” x 3/16” keyseat.
1TC70 - 1TC240
BrowningSplitTaperBushings
• Keyed to shaft and hub.
External key provides positive
drive with no torque on the cap
screws.
• Highest torque carrying
capacity.
• Double split barrel assures true
concentricity.
• Inch, metric and spline bores
available from stock.
• 1 - 6 grooves
• 7.40” - 24.40” O.D.
• 1/2” - 2 5/8” bore range
• Machined from fine grain cast iron
• Precision balanced
• Easy on - easy off
“C” Belts
7/8" x 17/32"
DIAMETERS 1 Groove, Face Width = 1 1/4”
Datum
“C”
Out-
side
In-
side
Part Number Dimensions
Wt.
Less
Bush.
Sheave Bushing O.L.
7.0” 7.40” — 1TC70 Q1 2 25/32” 9.3
7.2 7.60 — 1TC72 Q1 2 25/32 10.1
7.4 7.80 — 1TC74 Q1 2 25/32 10.8
7.6 8.00 — 1TC76 Q1 2 25/32 11.4
7.8 8.20 6” 1TC78 Q1 2 25/32 9.8
8.0 8.40 6 1/4 1TC80 Q1 2 25/32 9.9
8.2 8.60 6 7/16 1TC82 Q1 2 25/32 10.1
8.4 8.80 6 5/8 1TC84 Q1 2 25/32 11.0
8.6 9.00 6 13/16 1TC86 Q1 2 25/32 10.6
8.8 9.20 7 1TC88 Q1 2 25/32 11.6
9.0 9.40 7 1/4 1TC90 Q1 2 25/32 11.4
9.2 9.60 7 7/16 1TC92 Q1 2 25/32 12.6
9.4 9.80 7 5/8 1TC94 Q1 2 25/32 14.8
9.6 10.00 7 13/16 1TC96 Q1 2 25/32 15.8
9.8 10.20 8 1TC98 Q1 2 25/32 15.9
10.0 10.40 8 1/4 1TC100 Q1 2 25/32 16.8
10.2 10.60 8 7/16 1TC102 Q1 2 25/32 16.1
10.6 11.00 8 13/16 1TC106 Q1 2 25/32 17.3
11.0 11.40 9 1/4 1TC110 Q1 2 25/32 17.5
11.4 11.80 9 5/8 1TC114 Q1 2 25/32 18.6
12.0 12.40 10 1/4 1TC120 Q1 2 25/32 19.5
13.0 13.40 11 1/4 1TC130 Q1 2 25/32 22.8
16.0 16.40 14 1/4 1TC160 Q1 2 25/32 28.5
20.0 20.40 18 1/4 1TC200 Q1 2 25/32 37.8
24.0 24.40 22 1/4 1TC240 Q1 2 25/32 49.5
Bore Range Keyseat
3/4”—7/8” 3/16” x 3/32”
15/16—1 1/4 1/4 x 1/8
1 5/16—1 3/8 5/16 x 5/32
1 7/16—1 3/4 3/8 x 3/16
1 13/16—2 1/4 1/2 x 1/4
2 5/16—2 11/16 5/8 x 5/16
Part
No.
Bore
Range
Wt.
Lbs.
Q1 3/4”—2 11/16” 3 1/2