MSDS

MATERIAL SAFETY DATA SHEET
I. PRODUCT IDENTIFICATION
Name: Hartco Wood Filler
Description: Acrylic Filler
II. DEPARTMENT OF TRANSPORTATION INFORMATION
Shipping name: Not Classified Hazard Class: N/A
ID #: N/A Packing Inst.: N/A DOT/IMO/IATA: N/A
EMERGENCY ONLY CONTACT: CHEM-TEL [phone]
III. HMIS (0=minimal hazard; 4 = severe hazard)
Health = 1 Flammability = 0 Reactivity = 0
IV. PRODUCT CONTENT
This product does not contain chemicals subject to the reporting
requirements of Section 313 of SARA Title III and 40 CFR 372. All
components are on TSCA inventory. This product does NOT contain
asbestos.
V. PRODUCT INGREDIENTS
(Chemical Identity; Common Name) C.A.S. No. % OSHA PEL ACGIH TLV
Calcium Carbonate 1317-65-3 60 – 70% 15 mg/m3 10 mg/m3
As respirable dust:
5 mg/m3
Polyvinyl Acetate 9003-20-7 8 – 10 N/A N/A
Propylene Glycol 57-55-6 2 – 4 N/A N/A
VI. PHYSICAL DATA
APPEARANCE AND COLOR: Tan - brown solid. ODOR:
Similar to fill dirt. BOILING POINT (degrees F): N/A VAPOR
PRESSURE: N/A. VAPOR DENSITY: Heavier than air.
SOLUBILITY IN WATER: Insoluble. SPECIFIC GRAVITY: 1.7
PERCENT VOLATILE BY WEIGHT: 2.7%. EVAPORATION
RATE: Slower than butyl acetate. PH: N/A.
VII. FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: N/A. FLAMMABLE LIMITS IN AIR, 5 BY
VOLUME: LEL = N/A; UEL = N/A. EXTINGUISHING MEDIA:
Carbon dioxide, dry chemical, water spray. SPECIAL FIRE
FIGHTING ROCEDURES: Protect fire fighters from toxic
products of combustion by wearing self-contained breathing
apparatus. UNUSUAL FIRE AND EXPLOSION HAZARDS:
Closed containers in a fire may rupture due to pressure build-
up; use water to cool containers to prevent this.
VIII. HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Direct dermal contact. EYE
CONTACT: Contact with eyes will cause irritation. Immediately
flush eyes with plenty of water for at least 15 minutes. Refer to
physician if irritation develops or symptoms persist.
SKIN CONTACT: Mild irritant, repeated contact may cause
irritation. Remove contaminated clothing. Wash skin with
soap and water. Refer to physician if irritation develops or
symptoms persist. INHALATION: N/A. INGESTION: If
swallowed, do NOT induce vomiting. Call a physician or
poison control center immediately. CARCINOGENICITY:
NTP: No. IARC Monographs: No. OSHA Regulated: No.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY
OVEREXPOSURE: Existing skin conditions.
IX. REACTIVITY DATA
STABILITY: Stable. INCOMPATIBILITY: Strong oxidizing
agents. HAZARDOUS DECOMPOSITION PRODUCTS:
Carbon monoxide, carbon dioxide, and other toxic vapors and
gases that are common to thermal degradation of organic
compounds. HAZARDOUS POLYMERIZATION: Will not occur.
X. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR
SPILLED: Contain spill, preventing it from entering sewer lines
or waterways. Use absorbent to assist with the pick-up of
material. Scrape up product and place into container. WASTE
DISPOSAL METHOD: Do not reuse container. Dispose of
container and any unused contents in accordance with
Federal, State and Local Waste Disposal Regulations. Do not
flush unused contents or residue down drains.
XI. SPECIAL HANDLING AND USE INFORMATION
VENTILATION: Normal ambient ventilation should be
sufficient. RESPIRATORY PROTECTION: Should not be
required. SKIN AND EYE PROTECTION: It is always a good
safety practice to avoid contact with eyes and prolonged
contact with skin. If contact may occur, use spectacle-type
glasses and latex or rubber gloves.
XII. SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND
STORAGE: Keep from freezing. Recommended storage
temperature is below 90
o
F. OTHER PRECAUTIONS: None.
WORK SITE ENVIRONMENT: Initially there may be a potential
adverse impact on indoor air quality within the general work
area during the installation process. Therefore you should
advise the building manager or other appropriate person that:
It will be necessary to establish and maintain adequate
ventilation of the work area, without causing the entry of
contaminants to other parts of the building. Persons who are
sensitive to odors and/or chemicals should be advised to avoid
the work area during this process.
The information presented herein is supplied as a guide to
those who handle or use this product. Safe work practices
must be employed when working with any materials. It is
important that the end user makes a determination regarding
the adequacy of the safety procedures employed during the
use of this product.
N/A - not applicable or not available N/K - none known or not known
Wood Filler
Prepared 6/09
Armstrong World Industries, Inc.
P. O. Box 3001
Lancaster, PA 17604
1-877-276-7876, Option 2,3,3