Warranty

Rev: 04/2010 Brush Master™ Chipper/Shredder with 2-Way Feed
13
Heavy Duty Power Equipment
Limited Warranty & Service
Products Covered by this
Warranty
Length of Warranty: *(from the date of original retail
purchase)
Noncommercial
/Nonrental
Commercial Rental
Engine 12 months 12 months 12 months
*Length of Warranty: Consumable parts such as oil, spark plugs, filters, blades, and belts are not covered by this warranty. Warranty repairs will be
made without charge for parts and labor for the first 6 months. After the first 6 months, the limited warranty covers the costs of replacement parts only.
To Qualify for this Warranty:
The product must be purchased in the United States from a dealer authorized by GXi Outdoor Power, LLC to sell the product. This warranty applies to
first retail purchaser/owner during the applicable warranty time period. No warranty registration is necessary to obtain warranty on Brush Beast or Turf
Beast products. Save your proof of purchase receipt.
To Obtain Warranty Service:
You must take the DEK Power Equipment product, accessory, replacement part, apparel or the power equipment on which the accessory or
replacement part is installed, and proof of purchase, at your expense, to any DEK Power Equipment service location in the United States, who is
authorized to service that product, during the service location’s normal business hours. If you are unable to obtain warranty service, or are dissatisfied
with the warranty service you receive, take the following steps: First, contact the manager of the service center involved; normally this will resolve the
problem. However, if you should require further assistance, write or call the GXi Customer Service.
What GXi Outdoor Power Will Repair or Replace under Warranty:
GXi will repair or replace, at its option, any part that is proven to be defective in material or workmanship under normal use during the applicable
warranty time period subject to the exclusions stated herein. GXi has the right to recover warranty administration costs from the owner if the root
cause of the malfunction is found to be other than defective material or workmanship. This warranty is void if the owner fails to follow the prescribed
operating, maintenance and storage procedures described in this manual. This specifically refers to ensuring routine oil changes are made, that fuel
stabilizer is used for long-term storage and that the chipper/shredder is used in accordance with the operating instructions.
Anything replaced under warranty becomes the property of GXi. Parts replaced under warranty will be considered as part of the original product and
any warranty on those parts will expire coincident with the original product warranty.
Exclusions:
This warranty does not cover: normal wear, contaminants in the fuel or oil; damage as a result of use in an application for which the product was not
designed; damage caused by incorporation or use of unsuitable attachments or parts, unauthorized alteration, or other misuse and neglector; damage
caused by failure to follow the prescribed warnings, operating practices, proper maintenance and storage procedures; parts affected or damaged by
accident and/or collision; damage due to shipping, handling, storage or any causes other than defects in material or workmanship of the product.
Disclaimer of Consequential Damage and Limitation of Implied Warranties:
GXI disclaims any responsibility for loss of time or use of the product, transportation, commercial loss, or any other incidental or consequential
damage. Any implied warranties are limited to the duration of this written limited warranty.
THIS WARRANTY IS VOID IF THE MANUFACTURING DATE AND THE SERIAL NUMBER ON THE EQUIPMENT HAS BEEN REMOVED OR
THE EQUIPMENT HAS BEEN MODIFIED.
EMISSION CONTROL SYSTEM INFORMATION
The U.S. and California Clean Air Acts
EPA and California regulations require all manufacturers to furnish written instructions describing the operation and maintenance of emission control
systems. The following instructions and procedures must be followed in order to keep the emissions from your STANLEY engine within the emission
standards. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any engine repair establishment or
individual, using parts that are ‘‘certified’’ to EPA standards.
The emission control systems on your STANLEY engine were designed, built, and certified to conform with EPA regulations. We recommend the use
of genuine STANLEY parts whenever you have maintenance done. These original-design replacement parts are manufactured to the same standards
as the original parts, so you can be confident of their performance. The use of replacement parts that are not of the original design and quality may
impair the effectiveness of your emission control system. A manufacturer of an aftermarket part assumes the responsibility that the part will not
adversely affect emission performance. The manufacturer or re-builder of the part must certify that use of the part will not result in a failure of the
engine to comply with emission regulations.
Emission controls are covered by this warranty for all uses for a period of 3 years from original retail purchase date, this coverage extends to
subsequent owners of the product with proof of original purchase.