TM Chipper/Shredder with 2-Way Feed Owner’s Manual This manual contains important safety instructions for Chipper/Shredder models: CH6, CH8 READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY SAVE THESE INSTRUCTIONS. Do not return this unit to the store! For product questions or service, CALL 1-919-550-3221 or go to www.beastpowerequipment.
T Copyright© 2012 by GXi Outdoor Power, LLC. All rights reserved. No part of this publication can be reproduced or distributed without prior written permission of GXi Outdoor Power, LLC Clayton, NC 27520 USA.
BEAST SERIES Check out our other great products at www.beastpowerequipment.
T Contents Warnings ...................................................................................1 Product Specifications...............................................................2 Component Identification ......................................................... 3 Missing Parts Order Form ........................................................ 4 Identification Component ..........................................................5 Safety Information ..............................................
T Warnings WARNING WARNING This symbol indicates important safety instructions which, if not followed, could endanger personal safety and/or property. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol—heed its warning. Keep bystanders, helpers, pets, and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.
Warnings T Training 7. Do not put hands or feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 1. Read, understand, and follow all instructions on the machine and in the manual before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts. 8.
Component Identification T Leaf Funnel Discharge Chute Chipped materials are discharged through this opening. Use the Leaf funnel to feed leaves and branches no larger than 1/4” only. Fuel Tank Limb Chute Use regular unleaded fuel. Always leave about 1” of air gap at the top of the tank for fuel expansion to prevent seepage or spills. Use the Limb chute to feed longer and/or thicker pieces of yard waste into the impeller for chipping. Depending on the model #, the chipper/shredder can cut up to a 2.
T Missing Parts Request Form Please indicate the part that you are missing: Name Address Date of purchase Model #: CH6 CH8 Phone Email Serial #: Comments: IMPORTANT: Please include your receipt. Without a receipt, your order will be delayed. You may also email us at: customerservice@gxioutdoorpower.com. If emailing, please scan in your proof of purchase. Refer to parts diagram and part list on page 5 and 6 for part numbers. This will expedite the process. Rev: 4.
T Rev: 4.
T Component Identification BEAST CH6 Chipper Shredder Spare Parts Diagram Item # GXi Part Number 1 LCSSP11-005 2 LCSSP11-002 3 LCSSP11-022 4 LCSSP11-004 5 LCS11-031 6 LCSSP11-028 7 LCSSP12-029 8 LCS11-039 9 LCS11-043 10 LCSSP11-008 11 LCSSP11-009 12 LCSSP11-010 13 LCSSP11-025 14 LCSSP11-012 15 LCSSP11-026 16 LCSSP11-014 17 LCSSP11-015 18 LCSSP11-016 19 LCSSP11-017 20 LCSSP11-018 21 LCSSP11-019 22 LCSSP11-020 23 LCSSP12-034 Description Chipper, plastic leaf funnel assembly kit with hardware and label for
T Safety Information Your Responsibility Restrict the use of this chipper/shredder to persons who read, understand and follow the warnings and instructions in this manual and on the machine. Note: Not all safety labels shown may apply to your chipper/shredder. i. Preparation 1. Thoroughly inspect the area where the chipper/ shredder is to be used. Remove all rocks, bottles, cans, or other foreign objects which could be picked up or thrown and cause personal injury or damage to the machine. j. k. 2.
T Operating Guidelines READ THESE OPERATING GUIDELINES BEFORE YOU PROCEED ANY FURTHER The side chute is for longer and/or thicker pieces of yard waste. Depending on your model, you may chip to your models capacity (page 2). 1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 2.
Assembly T 1 2 3 6 4 5 Figure 1 IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to fill the engine with gasoline and oil as instructed before operating your machine. Required tools: Two 13mm wrenches NOTE: Both wrenches are supplied in the hardware bag. Approximate assembly time: 15 minutes 1. Remove the chipper from its carton Remove plastic banding and cut the tape on the top of the box. 2.
Assembly T 5. Disconnect The Spark Plug Wire Before setting up your chipper shredder, disconnect the spark plug wire from the spark plug and ground against the engine to prevent inadvertent starting of the machine. This step should be taken as a precaution whenever you are working on this machine. 6. Attaching the chipper discharge chute (Figure 3) Place discharge chute over rectangular opening on the chipper body. The plastic discharge chute fits on the outside of the steel chipper body.
T Important Engine Information NOTE: The chipper/shredder operates most efficiently at the factory set engine speed of 3600 RPM. The speed is controlled by the governor, and the throttle setting should not be adjusted. Do not attempt to adjust the speed of the engine. WARNING Carbon Monoxide Gas Exhaust contains poisonous carbon monoxide, a colorless and odorless gas. Breathing exhaust can cause loss of consciousness and may lead to death.
Operating Instructions T Rapid retraction of the recoil starter cord can pull the starter cord back faster than you can let go. When starting the engine, pull the cord slowly until resistance is felt then pull rapidly to avoid kickback. DANGER This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury.
Maintenance and Storage T Maintenance Schedule 20 hrs or Before each every 3 use months Item Check for loose fasteners (check) X Engine Oil (Check) X Engine Oil (Change) 50 hrs or every 3 months 100 hrs or every 6 months 300 hrs or every 1 year X Air Cleaner (Check) X Air Cleaner Wash X Fuel filter Cup (Clean) X Spark Plug (Clean) X Spark Plug (Change) X Check Chipper Blade X Fuel Tank and Filter (Clean) X 6.
Maintenance and Storage T WARNING Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. Removing and Sharpening the Limb Chute Blades The chipper was shipped with two blades attached spare blades are sold in sets from GXi (Part Number LCSSP11-018) 1. Disconnect the spark plug wire and ground against the engine. 2.
Maintenance and Storage T WARNING Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. Removing and Sharpening the Leaf Funnel Blade 1. Disconnect the spark plug wire and ground against the engine. 2. Remove the lower section and upper section of the funnel as a subassembly. This is done by removing three bolts with the 13mm wrenches provided in the hardware bag. 3.
Troubleshooting T Problem Cause Remedy Engine fails to start 1. Spark plug wire disconnected. 2. Fuel tank empty or stale fuel. 3. Throttle control lever not in correct starting position. (If equipped) 4. Choke not in CHOKE position. (If equipped) 5. Engine not primed. 6. Blocked fuel line. 7. Faulty spark plug. 8. Low oil 1. Connect wire to spark plug. 2. Fill tank with clean, fresh gasoline. 3. Move throttle lever to FAST position. Engine runs erratic 1. Spark plug wire loose. 2.
T Limited Warranty & Service Length of Warranty: *(from the date of original retail Products Covered by this Warranty Engine purchase) Noncommercial /Nonrental 12 months Commercial 3 months Rental 3 months *Length of Warranty: Consumable parts such as oil, spark plugs, filters, blades, and belts are not covered by this warranty. Warranty repairs will be made without charge for parts and labor for the first 6 months.
